diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 9556536..f46bf00 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -13,6 +13,7 @@
 obj-$(CONFIG_PHYLIB_10G) += generic_10g.o
 obj-$(CONFIG_PHY_ATHEROS) += atheros.o
 obj-$(CONFIG_PHY_BROADCOM) += broadcom.o
+obj-$(CONFIG_PHY_CORTINA) += cortina.o
 obj-$(CONFIG_PHY_DAVICOM) += davicom.o
 obj-$(CONFIG_PHY_ET1011C) += et1011c.o
 obj-$(CONFIG_PHY_LXT) += lxt.o
diff --git a/drivers/net/phy/cortina.c b/drivers/net/phy/cortina.c
new file mode 100644
index 0000000..254f056
--- /dev/null
+++ b/drivers/net/phy/cortina.c
@@ -0,0 +1,333 @@
+/*
+ * Cortina CS4315/CS4340 10G PHY drivers
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ *
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ */
+
+#include <config.h>
+#include <common.h>
+#include <malloc.h>
+#include <linux/ctype.h>
+#include <linux/string.h>
+#include <linux/err.h>
+#include <phy.h>
+#include <cortina.h>
+#ifdef CONFIG_SYS_CORTINA_FW_IN_NAND
+#include <nand.h>
+#elif defined(CONFIG_SYS_CORTINA_FW_IN_SPIFLASH)
+#include <spi_flash.h>
+#elif defined(CONFIG_SYS_CORTINA_FW_IN_MMC)
+#include <mmc.h>
+#endif
+
+#ifndef CONFIG_PHYLIB_10G
+#error The Cortina PHY needs 10G support
+#endif
+
+struct cortina_reg_config cortina_reg_cfg[] = {
+	/* CS4315_enable_sr_mode */
+	{VILLA_GLOBAL_MSEQCLKCTRL, 0x8004},
+	{VILLA_MSEQ_OPTIONS, 0xf},
+	{VILLA_MSEQ_PC, 0x0},
+	{VILLA_MSEQ_BANKSELECT,	   0x4},
+	{VILLA_LINE_SDS_COMMON_SRX0_RX_CPA, 0x55},
+	{VILLA_LINE_SDS_COMMON_SRX0_RX_LOOP_FILTER, 0x30},
+	{VILLA_DSP_SDS_SERDES_SRX_DFE0_SELECT, 0x1},
+	{VILLA_DSP_SDS_DSP_COEF_DFE0_SELECT, 0x2},
+	{VILLA_LINE_SDS_COMMON_SRX0_RX_CPB, 0x2003},
+	{VILLA_DSP_SDS_SERDES_SRX_FFE_DELAY_CTRL, 0xF047},
+	{VILLA_MSEQ_ENABLE_MSB, 0x0000},
+	{VILLA_MSEQ_SPARE21_LSB, 0x6},
+	{VILLA_MSEQ_RESET_COUNT_LSB, 0x0},
+	{VILLA_MSEQ_SPARE12_MSB, 0x0000},
+	/*
+	 * to invert the receiver path, uncomment the next line
+	 * write (VILLA_MSEQ_SPARE12_MSB, 0x4000)
+	 *
+	 * SPARE2_LSB is used to configure the device while in sr mode to
+	 * enable power savings and to use the optical module LOS signal.
+	 * in power savings mode, the internal prbs checker can not be used.
+	 * if the optical module LOS signal is used as an input to the micro
+	 * code, then the micro code will wait until the optical module
+	 * LOS = 0 before turning on the adaptive equalizer.
+	 * Setting SPARE2_LSB bit 0 to 1 places the devie in power savings mode
+	 * while setting bit 0 to 0 disables power savings mode.
+	 * Setting SPARE2_LSB bit 2 to 0 configures the device to use the
+	 * optical module LOS signal while setting bit 2 to 1 configures the
+	 * device so that it will ignore the optical module LOS SPARE2_LSB = 0
+	 */
+
+	/* enable power savings, ignore optical module LOS */
+	{VILLA_MSEQ_SPARE2_LSB, 0x5},
+
+	{VILLA_MSEQ_SPARE7_LSB, 0x1e},
+	{VILLA_MSEQ_BANKSELECT, 0x4},
+	{VILLA_MSEQ_SPARE9_LSB, 0x2},
+	{VILLA_MSEQ_SPARE3_LSB, 0x0F53},
+	{VILLA_MSEQ_SPARE3_MSB, 0x2006},
+	{VILLA_MSEQ_SPARE8_LSB, 0x3FF7},
+	{VILLA_MSEQ_SPARE8_MSB, 0x0A46},
+	{VILLA_MSEQ_COEF8_FFE0_LSB, 0xD500},
+	{VILLA_MSEQ_COEF8_FFE1_LSB, 0x0200},
+	{VILLA_MSEQ_COEF8_FFE2_LSB, 0xBA00},
+	{VILLA_MSEQ_COEF8_FFE3_LSB, 0x0100},
+	{VILLA_MSEQ_COEF8_FFE4_LSB, 0x0300},
+	{VILLA_MSEQ_COEF8_FFE5_LSB, 0x0300},
+	{VILLA_MSEQ_COEF8_DFE0_LSB, 0x0700},
+	{VILLA_MSEQ_COEF8_DFE0N_LSB, 0x0E00},
+	{VILLA_MSEQ_COEF8_DFE1_LSB, 0x0B00},
+	{VILLA_DSP_SDS_DSP_COEF_LARGE_LEAK, 0x2},
+	{VILLA_DSP_SDS_SERDES_SRX_DAC_ENABLEB_LSB, 0xD000},
+	{VILLA_MSEQ_POWER_DOWN_LSB, 0xFFFF},
+	{VILLA_MSEQ_POWER_DOWN_MSB, 0x0},
+	{VILLA_MSEQ_CAL_RX_SLICER, 0x80},
+	{VILLA_DSP_SDS_SERDES_SRX_DAC_BIAS_SELECT1_MSB, 0x3f},
+	{VILLA_GLOBAL_MSEQCLKCTRL, 0x4},
+	{VILLA_MSEQ_OPTIONS, 0x7},
+
+	/* set up min value for ffe1 */
+	{VILLA_MSEQ_COEF_INIT_SEL, 0x2},
+	{VILLA_DSP_SDS_DSP_PRECODEDINITFFE21, 0x41},
+
+	/* CS4315_sr_rx_pre_eq_set_4in */
+	{VILLA_GLOBAL_MSEQCLKCTRL, 0x8004},
+	{VILLA_MSEQ_OPTIONS, 0xf},
+	{VILLA_MSEQ_BANKSELECT, 0x4},
+	{VILLA_MSEQ_PC, 0x0},
+
+	/* for lengths from 3.5 to 4.5inches */
+	{VILLA_MSEQ_SERDES_PARAM_LSB, 0x0306},
+	{VILLA_MSEQ_SPARE25_LSB, 0x0306},
+	{VILLA_MSEQ_SPARE21_LSB, 0x2},
+	{VILLA_MSEQ_SPARE23_LSB, 0x2},
+	{VILLA_MSEQ_CAL_RX_DFE_EQ, 0x0},
+
+	{VILLA_GLOBAL_MSEQCLKCTRL, 0x4},
+	{VILLA_MSEQ_OPTIONS, 0x7},
+
+	/* CS4315_rx_drive_4inch */
+	/* for length  4inches */
+	{VILLA_GLOBAL_VILLA2_COMPATIBLE, 0x0000},
+	{VILLA_HOST_SDS_COMMON_STX0_TX_OUTPUT_CTRLA, 0x3023},
+	{VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLB, 0xc01E},
+
+	/* CS4315_tx_drive_4inch */
+	/* for length  4inches */
+	{VILLA_GLOBAL_VILLA2_COMPATIBLE, 0x0000},
+	{VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLA, 0x3023},
+	{VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLB, 0xc01E},
+};
+
+void cs4340_upload_firmware(struct phy_device *phydev)
+{
+	char line_temp[0x50] = {0};
+	char reg_addr[0x50] = {0};
+	char reg_data[0x50] = {0};
+	int i, line_cnt = 0, column_cnt = 0;
+	struct cortina_reg_config fw_temp;
+	char *addr = NULL;
+
+#if defined(CONFIG_SYS_CORTINA_FW_IN_NOR) || \
+	defined(CONFIG_SYS_CORTINA_FW_IN_REMOTE)
+
+	addr = (char *)CONFIG_CORTINA_FW_ADDR;
+#elif defined(CONFIG_SYS_CORTINA_FW_IN_NAND)
+	int ret;
+	size_t fw_length = CONFIG_CORTINA_FW_LENGTH;
+
+	addr = malloc(CONFIG_CORTINA_FW_LENGTH);
+	ret = nand_read(&nand_info[0], (loff_t)CONFIG_CORTINA_FW_ADDR,
+		       &fw_length, (u_char *)addr);
+	if (ret == -EUCLEAN) {
+		printf("NAND read of Cortina firmware at 0x%x failed %d\n",
+		       CONFIG_CORTINA_FW_ADDR, ret);
+	}
+#elif defined(CONFIG_SYS_CORTINA_FW_IN_SPIFLASH)
+	int ret;
+	struct spi_flash *ucode_flash;
+
+	addr = malloc(CONFIG_CORTINA_FW_LENGTH);
+	ucode_flash = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS,
+				CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE);
+	if (!ucode_flash) {
+		puts("SF: probe for Cortina ucode failed\n");
+	} else {
+		ret = spi_flash_read(ucode_flash, CONFIG_CORTINA_FW_ADDR,
+				     CONFIG_CORTINA_FW_LENGTH, addr);
+		if (ret)
+			puts("SF: read for Cortina ucode failed\n");
+		spi_flash_free(ucode_flash);
+	}
+#elif defined(CONFIG_SYS_CORTINA_FW_IN_MMC)
+	int dev = CONFIG_SYS_MMC_ENV_DEV;
+	u32 cnt = CONFIG_CORTINA_FW_LENGTH / 512;
+	u32 blk = CONFIG_CORTINA_FW_ADDR / 512;
+	struct mmc *mmc = find_mmc_device(CONFIG_SYS_MMC_ENV_DEV);
+
+	if (!mmc) {
+		puts("Failed to find MMC device for Cortina ucode\n");
+	} else {
+		addr = malloc(CONFIG_CORTINA_FW_LENGTH);
+		printf("MMC read: dev # %u, block # %u, count %u ...\n",
+		       dev, blk, cnt);
+		mmc_init(mmc);
+		(void)mmc->block_dev.block_read(dev, blk, cnt, addr);
+		/* flush cache after read */
+		flush_cache((ulong)addr, cnt * 512);
+	}
+#endif
+
+	while (*addr != 'Q') {
+		i = 0;
+
+		while (*addr != 0x0a) {
+			line_temp[i++] = *addr++;
+			if (0x50 < i) {
+				printf("Not found Cortina PHY ucode at 0x%x\n",
+				       CONFIG_CORTINA_FW_ADDR);
+				return;
+			}
+		}
+
+		addr++;  /* skip '\n' */
+		line_cnt++;
+		column_cnt = i;
+		line_temp[column_cnt] = '\0';
+
+		if (CONFIG_CORTINA_FW_LENGTH < line_cnt)
+			return;
+
+		for (i = 0; i < column_cnt; i++) {
+			if (isspace(line_temp[i++]))
+				break;
+		}
+
+		memcpy(reg_addr, line_temp, i);
+		memcpy(reg_data, &line_temp[i], column_cnt - i);
+		strim(reg_addr);
+		strim(reg_data);
+		fw_temp.reg_addr = (simple_strtoul(reg_addr, NULL, 0)) & 0xffff;
+		fw_temp.reg_value = (simple_strtoul(reg_data, NULL, 0)) &
+				     0xffff;
+		phy_write(phydev, 0x00, fw_temp.reg_addr, fw_temp.reg_value);
+	}
+}
+
+int cs4340_phy_init(struct phy_device *phydev)
+{
+	int timeout = 100;  /* 100ms */
+	int reg_value;
+
+	/* step1: BIST test */
+	phy_write(phydev, 0x00, VILLA_GLOBAL_MSEQCLKCTRL,     0x0004);
+	phy_write(phydev, 0x00, VILLA_GLOBAL_LINE_SOFT_RESET, 0x0000);
+	phy_write(phydev, 0x00, VILLA_GLOBAL_BIST_CONTROL,    0x0001);
+	while (--timeout) {
+		reg_value = phy_read(phydev, 0x00, VILLA_GLOBAL_BIST_STATUS);
+		if (reg_value & mseq_edc_bist_done) {
+			if (0 == (reg_value & mseq_edc_bist_fail))
+				break;
+		}
+		udelay(1000);
+	}
+
+	if (!timeout) {
+		printf("%s BIST mseq_edc_bist_done timeout!\n", __func__);
+		return -1;
+	}
+
+	/* setp2: upload ucode */
+	cs4340_upload_firmware(phydev);
+	reg_value = phy_read(phydev, 0x00, VILLA_GLOBAL_DWNLD_CHECKSUM_STATUS);
+	if (reg_value) {
+		debug("%s checksum status failed.\n", __func__);
+		return -1;
+	}
+
+	return 0;
+}
+
+int cs4340_config(struct phy_device *phydev)
+{
+	cs4340_phy_init(phydev);
+	return 0;
+}
+
+int cs4340_startup(struct phy_device *phydev)
+{
+	phydev->link = 1;
+
+	/* For now just lie and say it's 10G all the time */
+	phydev->speed = SPEED_10000;
+	phydev->duplex = DUPLEX_FULL;
+	return 0;
+}
+
+struct phy_driver cs4340_driver = {
+	.name = "Cortina CS4315/CS4340",
+	.uid = PHY_UID_CS4340,
+	.mask = 0xfffffff0,
+	.features = PHY_10G_FEATURES,
+	.mmds = (MDIO_DEVS_PMAPMD | MDIO_DEVS_PCS |
+		 MDIO_DEVS_PHYXS | MDIO_DEVS_AN |
+		 MDIO_DEVS_VEND1 | MDIO_DEVS_VEND2),
+	.config = &cs4340_config,
+	.startup = &cs4340_startup,
+	.shutdown = &gen10g_shutdown,
+};
+
+int phy_cortina_init(void)
+{
+	phy_register(&cs4340_driver);
+	return 0;
+}
+
+int get_phy_id(struct mii_dev *bus, int addr, int devad, u32 *phy_id)
+{
+	int phy_reg;
+	bool is_cortina_phy = false;
+
+	switch (addr) {
+#ifdef CORTINA_PHY_ADDR1
+	case CORTINA_PHY_ADDR1:
+#endif
+#ifdef CORTINA_PHY_ADDR2
+	case CORTINA_PHY_ADDR2:
+#endif
+#ifdef CORTINA_PHY_ADDR3
+	case CORTINA_PHY_ADDR3:
+#endif
+#ifdef CORTINA_PHY_ADDR4
+	case CORTINA_PHY_ADDR4:
+#endif
+		is_cortina_phy = true;
+		break;
+	default:
+		break;
+	}
+
+	/* Cortina PHY has non-standard offset of PHY ID registers */
+	if (is_cortina_phy)
+		phy_reg = bus->read(bus, addr, 0, VILLA_GLOBAL_CHIP_ID_LSB);
+	else
+		phy_reg = bus->read(bus, addr, devad, MII_PHYSID1);
+
+	if (phy_reg < 0)
+		return -EIO;
+
+	*phy_id = (phy_reg & 0xffff) << 16;
+	if (is_cortina_phy)
+		phy_reg = bus->read(bus, addr, 0, VILLA_GLOBAL_CHIP_ID_MSB);
+	else
+		phy_reg = bus->read(bus, addr, devad, MII_PHYSID2);
+
+	if (phy_reg < 0)
+		return -EIO;
+
+	*phy_id |= (phy_reg & 0xffff);
+
+	return 0;
+}
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 467c972..5b04c85 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -448,6 +448,9 @@
 #ifdef CONFIG_PHY_BROADCOM
 	phy_broadcom_init();
 #endif
+#ifdef CONFIG_PHY_CORTINA
+	phy_cortina_init();
+#endif
 #ifdef CONFIG_PHY_DAVICOM
 	phy_davicom_init();
 #endif