mtd: nand: omap: remove unused #defines from common omap_gpmc.h
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
- GPMC_NAND_ECC_LP_x8_LAYOUT (for large page x8 NAND)
- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
- GPMC_NAND_ECC_SP_x8_LAYOUT (for small page x8 NAND)
2) removes unused #defines in common omap_gpmc.h depending on above configs
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5
Signed-off-by: Pekon Gupta <pekon@ti.com>
diff --git a/arch/arm/include/asm/omap_gpmc.h b/arch/arm/include/asm/omap_gpmc.h
index 5250109..3caaed8 100644
--- a/arch/arm/include/asm/omap_gpmc.h
+++ b/arch/arm/include/asm/omap_gpmc.h
@@ -12,53 +12,6 @@
#define GPMC_BUF_EMPTY 0
#define GPMC_BUF_FULL 1
-/* Generic ECC Layouts */
-/* Large Page x8 NAND device Layout */
-#ifdef GPMC_NAND_ECC_LP_x8_LAYOUT
-#define GPMC_NAND_HW_ECC_LAYOUT {\
- .eccbytes = 12,\
- .eccpos = {1, 2, 3, 4, 5, 6, 7, 8,\
- 9, 10, 11, 12},\
- .oobfree = {\
- {.offset = 13,\
- .length = 51 } } \
-}
-#endif
-
-/* Large Page x16 NAND device Layout */
-#ifdef GPMC_NAND_ECC_LP_x16_LAYOUT
-#define GPMC_NAND_HW_ECC_LAYOUT {\
- .eccbytes = 12,\
- .eccpos = {2, 3, 4, 5, 6, 7, 8, 9,\
- 10, 11, 12, 13},\
- .oobfree = {\
- {.offset = 14,\
- .length = 50 } } \
-}
-#endif
-
-/* Small Page x8 NAND device Layout */
-#ifdef GPMC_NAND_ECC_SP_x8_LAYOUT
-#define GPMC_NAND_HW_ECC_LAYOUT {\
- .eccbytes = 3,\
- .eccpos = {1, 2, 3},\
- .oobfree = {\
- {.offset = 4,\
- .length = 12 } } \
-}
-#endif
-
-/* Small Page x16 NAND device Layout */
-#ifdef GPMC_NAND_ECC_SP_x16_LAYOUT
-#define GPMC_NAND_HW_ECC_LAYOUT {\
- .eccbytes = 3,\
- .eccpos = {2, 3, 4},\
- .oobfree = {\
- {.offset = 5,\
- .length = 11 } } \
-}
-#endif
-
enum omap_ecc {
/* 1-bit ECC calculation by Software, Error detection by Software */
OMAP_ECC_HAM1_CODE_SW = 1, /* avoid un-initialized int can be 0x0 */
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h
index 59a8f36..a5736b7 100644
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@@ -404,7 +404,6 @@
/* NAND support */
#ifdef CONFIG_NAND
#define CONFIG_CMD_NAND
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#if !defined(CONFIG_SPI_BOOT) && !defined(CONFIG_NOR_BOOT)
#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:128k(SPL)," \
diff --git a/include/configs/am335x_igep0033.h b/include/configs/am335x_igep0033.h
index 115d1b3..c00d54f 100644
--- a/include/configs/am335x_igep0033.h
+++ b/include/configs/am335x_igep0033.h
@@ -188,7 +188,6 @@
#define CONFIG_NAND
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_NAND_OMAP_ELM
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_SYS_NAND_BASE (0x08000000) /* phys address CS0 */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_ONFI_DETECTION 1
diff --git a/include/configs/am3517_crane.h b/include/configs/am3517_crane.h
index 468fb43..4407b45 100644
--- a/include/configs/am3517_crane.h
+++ b/include/configs/am3517_crane.h
@@ -268,7 +268,6 @@
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_IS_IN_NAND 1
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h
index b8b99c8..0102ff5 100644
--- a/include/configs/am3517_evm.h
+++ b/include/configs/am3517_evm.h
@@ -277,7 +277,6 @@
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_IS_IN_NAND 1
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h
index 08c67f5..cfc4f9b 100644
--- a/include/configs/cm_t35.h
+++ b/include/configs/cm_t35.h
@@ -156,8 +156,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x8_LAYOUT
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
/* Environment information */
diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h
index 4f43ba9..16a00eb 100644
--- a/include/configs/devkit8000.h
+++ b/include/configs/devkit8000.h
@@ -116,8 +116,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_JFFS2_NAND
diff --git a/include/configs/dig297.h b/include/configs/dig297.h
index 5049afc..af6f56b 100644
--- a/include/configs/dig297.h
+++ b/include/configs/dig297.h
@@ -143,8 +143,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
#if defined(CONFIG_CMD_NET)
diff --git a/include/configs/mcx.h b/include/configs/mcx.h
index 7c5c2f4..47244c0 100644
--- a/include/configs/mcx.h
+++ b/include/configs/mcx.h
@@ -321,7 +321,6 @@
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
#define CONFIG_ENV_IS_IN_NAND
#define SMNAND_ENV_OFFSET 0x180000 /* environment starts here */
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index c58bc91..ac0ed43 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -183,8 +183,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
diff --git a/include/configs/omap3_evm_common.h b/include/configs/omap3_evm_common.h
index 43616e2..7f3424b 100644
--- a/include/configs/omap3_evm_common.h
+++ b/include/configs/omap3_evm_common.h
@@ -208,7 +208,6 @@
#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#elif defined(CONFIG_CMD_ONENAND)
#define CONFIG_SYS_FLASH_BASE PISMO1_ONEN_BASE
diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h
index 20fbbec..12d8141 100644
--- a/include/configs/omap3_igep00x0.h
+++ b/include/configs/omap3_igep00x0.h
@@ -154,7 +154,6 @@
#ifdef CONFIG_NAND
#define PISMO1_NAND_SIZE GPMC_SIZE_128M /* Configure the PISMO */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */
#define CONFIG_ENV_IS_IN_NAND 1
#define CONFIG_ENV_SIZE (512 << 10) /* Total Size Environment */
diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h
index bedd6f9..0d03c75 100644
--- a/include/configs/omap3_logic.h
+++ b/include/configs/omap3_logic.h
@@ -295,7 +295,6 @@
#if defined(CONFIG_CMD_NAND)
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#endif
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index e0f0262..007e27f 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -119,8 +119,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand */
/* at CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_JFFS2_NAND
diff --git a/include/configs/omap3_pandora.h b/include/configs/omap3_pandora.h
index eacdfaa..da67787 100644
--- a/include/configs/omap3_pandora.h
+++ b/include/configs/omap3_pandora.h
@@ -131,8 +131,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand */
/* at CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h
index 1dd53fa..f0fa96e 100644
--- a/include/configs/omap3_zoom1.h
+++ b/include/configs/omap3_zoom1.h
@@ -138,8 +138,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_JFFS2_NAND
diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h
index 2863042..98b6e72 100644
--- a/include/configs/siemens-am33x-common.h
+++ b/include/configs/siemens-am33x-common.h
@@ -457,7 +457,6 @@
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_NAND_OMAP_ELM
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_SYS_NAND_BASE (0x08000000) /* physical address */
/* to access nand at */
/* CS0 */
diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h
index d44b5c0..3522c1a 100644
--- a/include/configs/tam3517-common.h
+++ b/include/configs/tam3517-common.h
@@ -186,7 +186,6 @@
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define CONFIG_NAND_OMAP_GPMC
-#define GPMC_NAND_ECC_LP_x16_LAYOUT
#define CONFIG_ENV_IS_IN_NAND
#define SMNAND_ENV_OFFSET 0x180000 /* environment starts here */
diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h
index cc4001f..62f97d2 100644
--- a/include/configs/tricorder.h
+++ b/include/configs/tricorder.h
@@ -134,8 +134,6 @@
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access nand at */
/* CS0 */
-#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
#define CONFIG_BCH