Enabled the Freescale SGMII riser card on 8572DS
This patch based on Andy's work.
Including command 'pixis_set_sgmii' support.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
diff --git a/board/freescale/mpc8572ds/mpc8572ds.c b/board/freescale/mpc8572ds/mpc8572ds.c
index 74f1df2..b2402dc 100644
--- a/board/freescale/mpc8572ds/mpc8572ds.c
+++ b/board/freescale/mpc8572ds/mpc8572ds.c
@@ -33,8 +33,10 @@
#include <miiphy.h>
#include <libfdt.h>
#include <fdt_support.h>
+#include <tsec.h>
#include "../common/pixis.h"
+#include "../common/sgmii_riser.h"
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
extern void ddr_enable_ecc(unsigned int dram_size);
@@ -519,6 +521,52 @@
}
#endif
+#ifdef CONFIG_TSEC_ENET
+int board_eth_init(bd_t *bis)
+{
+ struct tsec_info_struct tsec_info[4];
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ int num = 0;
+
+#ifdef CONFIG_TSEC1
+ SET_STD_TSEC_INFO(tsec_info[num], 1);
+ if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII1_DIS))
+ tsec_info[num].flags |= TSEC_SGMII;
+ num++;
+#endif
+#ifdef CONFIG_TSEC2
+ SET_STD_TSEC_INFO(tsec_info[num], 2);
+ if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII2_DIS))
+ tsec_info[num].flags |= TSEC_SGMII;
+ num++;
+#endif
+#ifdef CONFIG_TSEC3
+ SET_STD_TSEC_INFO(tsec_info[num], 3);
+ if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII3_DIS))
+ tsec_info[num].flags |= TSEC_SGMII;
+ num++;
+#endif
+#ifdef CONFIG_TSEC4
+ SET_STD_TSEC_INFO(tsec_info[num], 4);
+ if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII4_DIS))
+ tsec_info[num].flags |= TSEC_SGMII;
+ num++;
+#endif
+
+ if (!num) {
+ printf("No TSECs initialized\n");
+
+ return 0;
+ }
+
+ fsl_sgmii_riser_init(tsec_info, num);
+
+ tsec_eth_init(bis, tsec_info, num);
+
+ return 0;
+}
+#endif
+
#if defined(CONFIG_OF_BOARD_SETUP)
void ft_board_setup(void *blob, bd_t *bd)
{
diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h
index c2606fa..5688589 100644
--- a/include/configs/MPC8572DS.h
+++ b/include/configs/MPC8572DS.h
@@ -239,6 +239,22 @@
#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
#define CONFIG_SYS_PIXIS_VBOOT_MASK 0xc0
+#define PIXIS_VSPEED2_TSEC1SER 0x8
+#define PIXIS_VSPEED2_TSEC2SER 0x4
+#define PIXIS_VSPEED2_TSEC3SER 0x2
+#define PIXIS_VSPEED2_TSEC4SER 0x1
+#define PIXIS_VCFGEN1_TSEC1SER 0x20
+#define PIXIS_VCFGEN1_TSEC2SER 0x20
+#define PIXIS_VCFGEN1_TSEC3SER 0x20
+#define PIXIS_VCFGEN1_TSEC4SER 0x20
+#define PIXIS_VSPEED2_MASK (PIXIS_VSPEED2_TSEC1SER \
+ | PIXIS_VSPEED2_TSEC2SER \
+ | PIXIS_VSPEED2_TSEC3SER \
+ | PIXIS_VSPEED2_TSEC4SER)
+#define PIXIS_VCFGEN1_MASK (PIXIS_VCFGEN1_TSEC1SER \
+ | PIXIS_VCFGEN1_TSEC2SER \
+ | PIXIS_VCFGEN1_TSEC3SER \
+ | PIXIS_VCFGEN1_TSEC4SER)
/* define to use L1 as initial stack */
#define CONFIG_L1_INIT_RAM
@@ -418,6 +434,14 @@
#define CONFIG_TSEC4 1
#define CONFIG_TSEC4_NAME "eTSEC4"
+#define CONFIG_PIXIS_SGMII_CMD
+#define CONFIG_FSL_SGMII_RISER 1
+#define SGMII_RISER_PHY_OFFSET 0x1c
+
+#ifdef CONFIG_FSL_SGMII_RISER
+#define CONFIG_SYS_TBIPA_VALUE 0x10 /* avoid conflict with eTSEC4 paddr */
+#endif
+
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC3_PHY_ADDR 2