imx: Extend PCL063 support for phyCORE-i.MX6ULL SOM
Extend PHYTEC phyBOARD-i.MX6UL for phyCORE-i.MX6UL SoM (PCL063)
with eMMC on SoM.
CPU: Freescale i.MX6ULL rev1.0 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 38C
Reset cause: POR
Model: Phytec phyBOARD-i.MX6ULL-Segin SBC
Board: PHYTEC phyCORE-i.MX6ULL
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial@02020000
Out: serial@02020000
Err: serial@02020000
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- eMMC
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
diff --git a/board/phytec/pcl063/spl.c b/board/phytec/pcl063/spl.c
index b93cd49..73a7746 100644
--- a/board/phytec/pcl063/spl.c
+++ b/board/phytec/pcl063/spl.c
@@ -13,6 +13,7 @@
#include <asm/arch/mx6-ddr.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/crm_regs.h>
+#include <asm/arch/sys_proto.h>
#include <fsl_esdhc.h>
/* Configuration for Micron MT41K256M16TW-107 IT:P, 32M x 16 x 8 -> 256MiB */
@@ -117,11 +118,32 @@
MX6_PAD_UART1_RTS_B__USDHC1_CD_B | MUX_PAD_CTRL(USDHC_PAD_CTRL),
};
+#ifndef CONFIG_NAND_MXS
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+ MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+ MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+#endif
+
static struct fsl_esdhc_cfg usdhc_cfg[] = {
{
.esdhc_base = USDHC1_BASE_ADDR,
.max_bus_width = 4,
},
+#ifndef CONFIG_NAND_MXS
+ {
+ .esdhc_base = USDHC2_BASE_ADDR,
+ .max_bus_width = 8,
+ },
+#endif
};
int board_mmc_getcd(struct mmc *mmc)
@@ -131,12 +153,58 @@
int board_mmc_init(bd_t *bis)
{
- imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ int i, ret;
+
+ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+ switch (i) {
+ case 0:
+ SETUP_IOMUX_PADS(usdhc1_pads);
+ usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ break;
+#ifndef CONFIG_NAND_MXS
+ case 1:
+ SETUP_IOMUX_PADS(usdhc2_pads);
+ usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ break;
+#endif
+ default:
+ printf("Warning - USDHC%d controller not supporting\n",
+ i + 1);
+ return 0;
+ }
- return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+ if (ret) {
+ printf("Warning: failed to initialize mmc dev %d\n", i);
+ return ret;
+ }
+ }
+
+ return 0;
}
+void board_boot_order(u32 *spl_boot_list)
+{
+ u32 bmode = imx6_src_get_boot_mode();
+ u8 boot_dev = BOOT_DEVICE_MMC1;
+
+ switch ((bmode & IMX6_BMODE_MASK) >> IMX6_BMODE_SHIFT) {
+ case IMX6_BMODE_SD:
+ case IMX6_BMODE_ESD:
+ boot_dev = BOOT_DEVICE_MMC1;
+ break;
+ case IMX6_BMODE_MMC:
+ case IMX6_BMODE_EMMC:
+ boot_dev = BOOT_DEVICE_MMC2;
+ break;
+ default:
+ /* Default - BOOT_DEVICE_MMC1 */
+ printf("Wrong board boot order\n");
+ break;
+ }
+
+ spl_boot_list[0] = boot_dev;
+}
#endif /* CONFIG_FSL_ESDHC */
void board_init_f(ulong dummy)