fdt: update bcm283x device tree sources to Linux 5.1-rc6 state
Updating the bcm283x device tree sources adds the device trees for
- Raspberry Pi 3 Model A+
- Raspberry Pi 3 Model B+
- Raspberry Pi Compute Module IO board rev1
- Raspberry Pi Compute Module 3 IO board V3.0
- Raspberry Pi Zero
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
diff --git a/arch/arm/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/dts/bcm2837-rpi-3-b-plus.dts
new file mode 100644
index 0000000..c6fa34c
--- /dev/null
+++ b/arch/arm/dts/bcm2837-rpi-3-b-plus.dts
@@ -0,0 +1,178 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-lan7515.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+ compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
+ model = "Raspberry Pi 3 Model B+";
+
+ chosen {
+ /* 8250 auxiliary UART instead of pl011 */
+ stdout-path = "serial1:115200n8";
+ };
+
+ memory@0 {
+ reg = <0 0x40000000>;
+ };
+
+ leds {
+ act {
+ gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ pwr {
+ label = "PWR";
+ gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&firmware {
+ expgpio: gpio {
+ compatible = "raspberrypi,firmware-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "BT_ON",
+ "WL_ON",
+ "STATUS_LED_R",
+ "LAN_RUN",
+ "",
+ "CAM_GPIO0",
+ "CAM_GPIO1",
+ "";
+ status = "okay";
+ };
+};
+
+&gpio {
+ /*
+ * Taken from rpi_SCH_3bplus_1p0_reduced.pdf and
+ * the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD1",
+ "RXD1",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "HDMI_HPD_N",
+ "STATUS_LED_G",
+ /* Used by BT module */
+ "CTS0",
+ "RTS0",
+ "TXD0",
+ "RXD0",
+ /* Used by Wifi */
+ "SD1_CLK",
+ "SD1_CMD",
+ "SD1_DATA0",
+ "SD1_DATA1",
+ "SD1_DATA2",
+ "SD1_DATA3",
+ "PWM0_OUT",
+ "PWM1_OUT",
+ "ETHCLK",
+ "WIFI_CLK",
+ "SDA0",
+ "SCL0",
+ "SMPS_SCL",
+ "SMPS_SDA",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+};
+
+&hdmi {
+ hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+ status = "okay";
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_gpio34>;
+ status = "okay";
+ bus-width = <4>;
+ non-removable;
+ mmc-pwrseq = <&wifi_pwrseq>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhost_gpio48>;
+ status = "okay";
+ bus-width = <4>;
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <2000000>;
+ shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_gpio14>;
+ status = "okay";
+};