include/configs/p3mx.h - filogic/uboot - Gitiles

 /*
  * (C) Copyright 2006
  * Stefan Roese, DENX Software Engineering, sr@denx.de.
  *
  * Based on original work by
  *      Roel Loeffen, (C) Copyright 2006 Prodrive B.V.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 /************************************************************************
  * p3mx.h - configuration for Prodrive P3M750 & P3M7448 boards
  *
  * The defines:
  * CONFIG_P3M750 or
  * CONFIG_P3M7448
  * are written into include/config.h by the "make xxx_config" command
  ***********************************************************************/
 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*-----------------------------------------------------------------------
  * High Level Configuration Options
  *----------------------------------------------------------------------*/
 #define CONFIG_P3Mx			/* used for both board versions	*/

 #define	CONFIG_SYS_TEXT_BASE	0xfff00000

 #if defined (CONFIG_P3M750)
 #define CONFIG_750FX			/* 750GL/GX/FX			*/
 #define CONFIG_HIGH_BATS		/* High BATs supported		*/
 #define CONFIG_SYS_BOARD_NAME		"P3M750"
 #define CONFIG_SYS_BUS_CLK		100000000
 #define CONFIG_SYS_TCLK		100000000
 #elif defined (CONFIG_P3M7448)
 #define CONFIG_74xx
 #define CONFIG_SYS_BOARD_NAME		"P3M7448"
 #define CONFIG_SYS_BUS_CLK		133333333
 #define CONFIG_SYS_TCLK		133333333
 #endif
 #define CONFIG_SYS_GT_DUAL_CPU			/* also for JTAG even with one cpu */

 /* which initialization functions to call for this board */
 #define CONFIG_SYS_BOARD_ASM_INIT	1
 #define CONFIG_BOARD_EARLY_INIT_F 1     /* Call board_early_init_f	*/
 #define CONFIG_MISC_INIT_R      1	/* Call misc_init_r()		*/

 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #ifdef CONFIG_P3M750
 #define CONFIG_SYS_SDRAM1_BASE		0x10000000	/* each 256 MByte	*/
 #endif

 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
 #if defined (CONFIG_P3M750)
 #define CONFIG_SYS_FLASH_BASE		0xff800000	/* start of flash banks	*/
 #define CONFIG_SYS_BOOT_SIZE		_8M		/* boot flash		*/
 #elif defined (CONFIG_P3M7448)
 #define CONFIG_SYS_FLASH_BASE		0xff000000	/* start of flash banks	*/
 #define CONFIG_SYS_BOOT_SIZE		_16M		/* boot flash		*/
 #endif
 #define CONFIG_SYS_BOOT_SPACE		CONFIG_SYS_FLASH_BASE	/* BOOT_CS0 flash 0    */
 #define CONFIG_SYS_MONITOR_BASE	0xfff00000
 #define CONFIG_SYS_RESET_ADDRESS	0xfff00100
 #define CONFIG_SYS_MALLOC_LEN		(256 << 10)	/* Reserve 256 kB for malloc */
 #define CONFIG_SYS_MISC_REGION_BASE	0xf0000000

 #define CONFIG_SYS_DFL_GT_REGS		0xf1000000	/* boot time GT_REGS */
 #define CONFIG_SYS_GT_REGS		0xf1000000	/* GT Registers are mapped here */
 #define CONFIG_SYS_INT_SRAM_BASE	0x42000000	/* GT offers 256k internal SRAM */

 /*-----------------------------------------------------------------------
  * Initial RAM & stack pointer (placed in internal SRAM)
  *----------------------------------------------------------------------*/
  /*
  * When locking data in cache you should point the CONFIG_SYS_INIT_RAM_ADDRESS
  * To an unused memory region. The stack will remain in cache until RAM
  * is initialized
 */
 #undef	CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR	0x42000000
 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)


 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
 #define CONFIG_MPSC			/* MV64460 Serial		*/
 #define CONFIG_MPSC_PORT	0
 #define CONFIG_BAUDRATE		115200	/* console baudrate		*/
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/

 /*-----------------------------------------------------------------------
  * Ethernet
  *----------------------------------------------------------------------*/
 /* Change the default ethernet port, use this define (options: 0, 1, 2) */
 #define CONFIG_SYS_ETH_PORT		ETH_0
 #define MV_ETH_DEVS		2
 #define CONFIG_PHY_RESET        1	/* reset phy upon startup         */
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */

 /*-----------------------------------------------------------------------
  * FLASH related
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_FLASH_CFI			/* The flash is CFI compatible		*/
 #define CONFIG_FLASH_CFI_DRIVER		/* Use common CFI driver		*/
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
 #define CONFIG_SYS_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/
 #define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
 #define CONFIG_SYS_FLASH_PROTECTION	1	/* use hardware flash protection	*/
 #define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */

 #define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
 #if defined (CONFIG_P3M750)
 #define CONFIG_ENV_SECT_SIZE	0x20000	/* one sector (1 device)		*/
 #elif defined (CONFIG_P3M7448)
 #define CONFIG_ENV_SECT_SIZE	0x40000	/* two sectors (2 devices parallel	*/
 #endif
 #define	CONFIG_ENV_SIZE		0x2000	/* Total Size of Environment Sector	*/
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)

 /*-----------------------------------------------------------------------
  * DDR SDRAM
  *----------------------------------------------------------------------*/
 #define CONFIG_MV64460_ECC

 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_I2C_SPEED		100000		/* I2C speed default	*/

 /* I2C RTC */
 #define CONFIG_RTC_M41T11	1
 #define CONFIG_SYS_I2C_RTC_ADDR	0x68
 #define CONFIG_SYS_M41T11_BASE_YEAR	1900	/* play along with linux	*/

 /*-----------------------------------------------------------------------
  * PCI stuff
  *----------------------------------------------------------------------*/
 #define PCI_HOST_ADAPTER 0		/* configure ar pci adapter	*/
 #define PCI_HOST_FORCE	1		/* configure as pci host	*/
 #define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/

 #undef CONFIG_PCI			/* include pci support		*/
 #ifdef CONFIG_PCI
 #define CONFIG_PCI_HOST PCI_HOST_FORCE	/* select pci host function	*/
 #define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
 #define CONFIG_PCI_SCAN_SHOW		/* show devices on bus		*/
 #endif /* CONFIG_PCI */

 /* PCI MEMORY MAP section */
 #define CONFIG_SYS_PCI0_MEM_BASE	0x80000000
 #define CONFIG_SYS_PCI0_MEM_SIZE	_128M
 #define CONFIG_SYS_PCI1_MEM_BASE	0x88000000
 #define CONFIG_SYS_PCI1_MEM_SIZE	_128M

 #define CONFIG_SYS_PCI0_0_MEM_SPACE	(CONFIG_SYS_PCI0_MEM_BASE)
 #define CONFIG_SYS_PCI1_0_MEM_SPACE	(CONFIG_SYS_PCI1_MEM_BASE)

 /* PCI I/O MAP section */
 #define CONFIG_SYS_PCI0_IO_BASE	0xfa000000
 #define CONFIG_SYS_PCI0_IO_SIZE	_16M
 #define CONFIG_SYS_PCI1_IO_BASE	0xfb000000
 #define CONFIG_SYS_PCI1_IO_SIZE	_16M

 #define CONFIG_SYS_PCI0_IO_SPACE	(CONFIG_SYS_PCI0_IO_BASE)
 #define CONFIG_SYS_PCI0_IO_SPACE_PCI	0x00000000
 #define CONFIG_SYS_PCI1_IO_SPACE	(CONFIG_SYS_PCI1_IO_BASE)
 #define CONFIG_SYS_PCI1_IO_SPACE_PCI	0x00000000

 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS (CONFIG_SYS_PCI0_IO_BASE)
 #define CONFIG_SYS_PCI_IDSEL 0x30

 #undef	CONFIG_BOOTARGS
 #define	CONFIG_EXTRA_ENV_SETTINGS_COMMON				\
 	"netdev=eth0\0"							\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
 	"addip=setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
 	"flash_nfs=run nfsargs addip addtty;"				\
 		"bootm ${kernel_addr}\0"				\
 	"flash_self=run ramargs addip addtty;"				\
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
 	        "bootm\0"						\
 	"rootpath=/opt/eldk/ppc_6xx\0"					\
 	"u-boot=p3mx/u-boot/u-boot.bin\0"				\
 	"load=tftp 100000 ${u-boot}\0"					\
 	"update=protect off fff00000 fff3ffff;era fff00000 fff3ffff;"	\
 		"cp.b 100000 fff00000 40000;"			        \
 		"setenv filesize;saveenv\0"				\
 	"upd=run load update\0"						\
 	"serverip=11.0.0.152\0"

 #if defined (CONFIG_P3M750)
 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	CONFIG_EXTRA_ENV_SETTINGS_COMMON				\
 	"hostname=p3m750\0"						\
 	"bootfile=/tftpboot/p3mx/vxWorks.st\0"				\
 	"kernel_addr=fc000000\0"					\
 	"ramdisk_addr=fc180000\0"					\
 	"vxfile=p3m750/vxWorks\0"					\
 	"vxuser=ddg\0"							\
 	"vxpass=ddg\0"							\
 	"vxtarget=target\0"						\
 	"vxflags=0x8\0"							\
 	"vxargs=setenv bootargs mgi(0,0)host:${vxfile} h=${serverip} "	\
 		"e=${ipaddr} u=${vxuser} pw=${vxpass} tn=${vxtarget} "	\
 		"f=${vxflags}\0"
 #elif defined (CONFIG_P3M7448)
 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	CONFIG_EXTRA_ENV_SETTINGS_COMMON				\
 	"hostname=p3m7448\0"
 #endif

 #if defined (CONFIG_P3M750)
 #define CONFIG_BOOTCOMMAND	"tftp;run vxargs;bootvx"
 #elif defined (CONFIG_P3M7448)
 #define CONFIG_BOOTCOMMAND	" "
 #endif

 #define CONFIG_BOOTDELAY	3	/* autoboot after 5 seconds */

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_SUBNETMASK
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_BOOTFILESIZE

 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DIAG
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NET
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_CACHE
 #define CONFIG_CMD_SDRAM


 /*-----------------------------------------------------------------------
  * Miscellaneous configurable options
  *----------------------------------------------------------------------*/
 #define CONFIG_SYS_HUSH_PARSER

 #define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
 #define CONFIG_SYS_PROMPT	        "=> "	/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE	        1024	/* Console I/O Buffer Size	*/
 #else
 #define CONFIG_SYS_CBSIZE	        256	/* Console I/O Buffer Size	*/
 #endif
 #define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS	        16	/* max number of command args	*/
 #define CONFIG_SYS_BARGSIZE	        CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size	*/

 #define CONFIG_SYS_MEMTEST_START	0x0400000 /* memtest works on	        */
 #define CONFIG_SYS_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/

 #define CONFIG_SYS_LOAD_ADDR		0x08000000	/* default load address */

 #define CONFIG_SYS_HZ		        1000	/* decrementer freq: 1 ms ticks */

 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define CONFIG_LOOPW            1       /* enable loopw command         */
 #define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 #define CONFIG_VERSION_VARIABLE 1	/* include version env variable */

 /*-----------------------------------------------------------------------
  * Marvell MV64460 config settings
  *----------------------------------------------------------------------*/
 /* Reset values for Port behavior (8bit/ 32bit, etc.) only corrected device width */
 #if defined (CONFIG_P3M750)
 #define CONFIG_SYS_BOOT_PAR		0x8FDFF87F	/* 16 bit flash, disable burst*/
 #elif defined (CONFIG_P3M7448)
 #define CONFIG_SYS_BOOT_PAR		0x8FEFFFFF	/* 32 bit flash, burst enabled */
 #endif

 /*
  * MPP[0]	Serial Port 0 TxD	TxD	OUT	Connected to P14 (buffered)
  * MPP[1]	Serial Port 0 RxD	RxD	IN	Connected to P14 (buffered)
  * MPP[2]	NC
  * MPP[3]	Serial Port 1 TxD	TxD	OUT	Connected to P14 (buffered)
  * MPP[4]	PCI Monarch#		GPIO	IN	Connected to P12
  * MPP[5]	Serial Port 1 RxD	RxD	IN	Connected to P14 (buffered)
  * MPP[6]	PMC Carrier Interrupt 0	Int	IN	Connected to P14
  * MPP[7]	PMC Carrier Interrupt 1	Int	IN	Connected to P14
  * MPP[8]	Reserved				Do not use
  * MPP[9]	Reserved				Do not use
  * MPP[10]	Reserved				Do not use
  * MPP[11]	Reserved				Do not use
  * MPP[12]	Phy 0 Interrupt		Int	IN
  * MPP[13]	Phy 1 Interrupt		Int	IN
  * MPP[14]	NC
  * MPP[15]	NC
  * MPP[16]	PCI Interrupt C		Int	IN	Connected to P11
  * MPP[17]	PCI Interrupt D		Int	IN	Connected to P11
  * MPP[18]	Watchdog NMI#		GPIO	IN	Connected to MPP[24]
  * MPP[19]	Watchdog Expired#	WDE	OUT	Connected to rst logic
  * MPP[20]	Watchdog Status		WD_STS	IN	Read back of rst by watchdog
  * MPP[21]	NC
  * MPP[22]	GP LED Green		GPIO	OUT
  * MPP[23]	GP LED Red		GPIO	OUT
  * MPP[24]	Watchdog NMI#		Int	OUT
  * MPP[25]	NC
  * MPP[26]	NC
  * MPP[27]	PCI Interrupt A		Int	IN	Connected to P11
  * MPP[28]	NC
  * MPP[29]	PCI Interrupt B		Int	IN	Connected to P11
  * MPP[30]	Module reset		GPIO	OUT	Board reset
  * MPP[31]	PCI EReady		GPIO	IN	Connected to P12
  */
 #define CONFIG_SYS_MPP_CONTROL_0	0x00303022
 #define CONFIG_SYS_MPP_CONTROL_1	0x00000000
 #define CONFIG_SYS_MPP_CONTROL_2	0x00004000
 #define CONFIG_SYS_MPP_CONTROL_3	0x00000004
 #define CONFIG_SYS_GPP_LEVEL_CONTROL	0x280730D0

 /*----------------------------------------------------------------------
  * Initial BAT mappings
  */

 /* NOTES:
  * 1) GUARDED and WRITE_THRU not allowed in IBATS
  * 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT
  */
 /* SDRAM */
 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | BATL_GUARDEDSTORAGE | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U

 /* init ram */
 #define CONFIG_SYS_IBAT1L  (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT1U  (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_256K | BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT1L  CONFIG_SYS_IBAT1L
 #define CONFIG_SYS_DBAT1U  CONFIG_SYS_IBAT1U

 /* PCI0, PCI1 in one BAT */
 #define CONFIG_SYS_IBAT2L BATL_NO_ACCESS
 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U
 #define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI0_MEM_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI0_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)

 /* GT regs, bootrom, all the devices, PCI I/O */
 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW)
 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_MISC_REGION_BASE | BATU_VS | BATU_VP | BATU_BL_256M)
 #define CONFIG_SYS_DBAT3L (CONFIG_SYS_MISC_REGION_BASE | BATL_CACHEINHIBIT | BATL_PP_RW | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U

 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_SDRAM1_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT4U (CONFIG_SYS_SDRAM1_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT4L (CONFIG_SYS_SDRAM1_BASE | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U

 /* set rest out of range for Linux !!!!!!!!!!! */

 /* IBAT5 and DBAT5 */
 #define CONFIG_SYS_IBAT5L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT5U (0x20000000 | BATU_BL_256M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT5L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U

 /* IBAT6 and DBAT6 */
 #define CONFIG_SYS_IBAT6L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT6U (0x20000000 | BATU_BL_256M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT6L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U

 /* IBAT7 and DBAT7 */
 #define CONFIG_SYS_IBAT7L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT7U (0x20000000 | BATU_BL_256M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT7L (0x20000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ		(8<<20) /* Initial Memory map for Linux */
 #define CONFIG_SYS_VXWORKS_MAC_PTR	0x42010000 /* use some memory in SRAM that's not used!!! */

 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
 #define CONFIG_SYS_CACHELINE_SIZE	32	/* For all MPC74xx CPUs		 */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif

 /*-----------------------------------------------------------------------
  * L2CR setup -- make sure this is right for your board!
  * look in include/mpc74xx.h for the defines used here
  */
 #define CONFIG_SYS_L2

 #if defined (CONFIG_750CX) || defined (CONFIG_750FX)
 #define L2_INIT 0
 #else
 #define L2_INIT		(L2CR_L2SIZ_2M | L2CR_L2CLK_3 | L2CR_L2RAM_BURST | \
 			L2CR_L2OH_5 | L2CR_L2CTL | L2CR_L2WT)
 #endif

 #define L2_ENABLE	(L2_INIT | L2CR_L2E)

 #ifndef __ASSEMBLY__
 #include <../board/Marvell/include/core.h>
 #endif

 #endif	/* __CONFIG_H */
	/*
	* (C) Copyright 2006
	* Stefan Roese, DENX Software Engineering, sr@denx.de.
	*
	* Based on original work by
	* Roel Loeffen, (C) Copyright 2006 Prodrive B.V.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	/************************************************************************
	* p3mx.h - configuration for Prodrive P3M750 & P3M7448 boards
	*
	* The defines:
	* CONFIG_P3M750 or
	* CONFIG_P3M7448
	* are written into include/config.h by the "make xxx_config" command
	***********************************************************************/
	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*-----------------------------------------------------------------------
	* High Level Configuration Options
	----------------------------------------------------------------------/
	#define CONFIG_P3Mx /* used for both board versions */

	#define CONFIG_SYS_TEXT_BASE 0xfff00000

	#if defined (CONFIG_P3M750)
	#define CONFIG_750FX /* 750GL/GX/FX */
	#define CONFIG_HIGH_BATS /* High BATs supported */
	#define CONFIG_SYS_BOARD_NAME "P3M750"
	#define CONFIG_SYS_BUS_CLK 100000000
	#define CONFIG_SYS_TCLK 100000000
	#elif defined (CONFIG_P3M7448)
	#define CONFIG_74xx
	#define CONFIG_SYS_BOARD_NAME "P3M7448"
	#define CONFIG_SYS_BUS_CLK 133333333
	#define CONFIG_SYS_TCLK 133333333
	#endif
	#define CONFIG_SYS_GT_DUAL_CPU /* also for JTAG even with one cpu */

	/* which initialization functions to call for this board */
	#define CONFIG_SYS_BOARD_ASM_INIT 1
	#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
	#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r() */

	/*-----------------------------------------------------------------------
	* Base addresses -- Note these are effective addresses where the
	* actual resources get mapped (not physical addresses)
	----------------------------------------------------------------------/
	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#ifdef CONFIG_P3M750
	#define CONFIG_SYS_SDRAM1_BASE 0x10000000 /* each 256 MByte */
	#endif

	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
	#if defined (CONFIG_P3M750)
	#define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of flash banks */
	#define CONFIG_SYS_BOOT_SIZE _8M /* boot flash */
	#elif defined (CONFIG_P3M7448)
	#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of flash banks */
	#define CONFIG_SYS_BOOT_SIZE _16M /* boot flash */
	#endif
	#define CONFIG_SYS_BOOT_SPACE CONFIG_SYS_FLASH_BASE /* BOOT_CS0 flash 0 */
	#define CONFIG_SYS_MONITOR_BASE 0xfff00000
	#define CONFIG_SYS_RESET_ADDRESS 0xfff00100
	#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc */
	#define CONFIG_SYS_MISC_REGION_BASE 0xf0000000

	#define CONFIG_SYS_DFL_GT_REGS 0xf1000000 /* boot time GT_REGS */
	#define CONFIG_SYS_GT_REGS 0xf1000000 /* GT Registers are mapped here */
	#define CONFIG_SYS_INT_SRAM_BASE 0x42000000 /* GT offers 256k internal SRAM */

	/*-----------------------------------------------------------------------
	* Initial RAM & stack pointer (placed in internal SRAM)
	----------------------------------------------------------------------/
	/*
	* When locking data in cache you should point the CONFIG_SYS_INIT_RAM_ADDRESS
	* To an unused memory region. The stack will remain in cache until RAM
	* is initialized
	*/
	#undef CONFIG_SYS_INIT_RAM_LOCK
	#define CONFIG_SYS_INIT_RAM_ADDR 0x42000000
	#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)


	/*-----------------------------------------------------------------------
	* Serial Port
	----------------------------------------------------------------------/
	#define CONFIG_MPSC /* MV64460 Serial */
	#define CONFIG_MPSC_PORT 0
	#define CONFIG_BAUDRATE 115200 /* console baudrate */
	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */

	/*-----------------------------------------------------------------------
	* Ethernet
	----------------------------------------------------------------------/
	/* Change the default ethernet port, use this define (options: 0, 1, 2) */
	#define CONFIG_SYS_ETH_PORT ETH_0
	#define MV_ETH_DEVS 2
	#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
	#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */

	/*-----------------------------------------------------------------------
	* FLASH related
	----------------------------------------------------------------------/
	#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
	#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
	#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */
	#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */

	#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
	#if defined (CONFIG_P3M750)
	#define CONFIG_ENV_SECT_SIZE 0x20000 /* one sector (1 device) */
	#elif defined (CONFIG_P3M7448)
	#define CONFIG_ENV_SECT_SIZE 0x40000 /* two sectors (2 devices parallel */
	#endif
	#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)

	/*-----------------------------------------------------------------------
	* DDR SDRAM
	----------------------------------------------------------------------/
	#define CONFIG_MV64460_ECC

	/*-----------------------------------------------------------------------
	* I2C
	----------------------------------------------------------------------/
	#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed default */

	/* I2C RTC */
	#define CONFIG_RTC_M41T11 1
	#define CONFIG_SYS_I2C_RTC_ADDR 0x68
	#define CONFIG_SYS_M41T11_BASE_YEAR 1900 /* play along with linux */

	/*-----------------------------------------------------------------------
	* PCI stuff
	----------------------------------------------------------------------/
	#define PCI_HOST_ADAPTER 0 /* configure ar pci adapter */
	#define PCI_HOST_FORCE 1 /* configure as pci host */
	#define PCI_HOST_AUTO 2 /* detected via arbiter enable */

	#undef CONFIG_PCI /* include pci support */
	#ifdef CONFIG_PCI
	#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
	#define CONFIG_PCI_PNP /* do pci plug-and-play */
	#define CONFIG_PCI_SCAN_SHOW /* show devices on bus */
	#endif /* CONFIG_PCI */

	/* PCI MEMORY MAP section */
	#define CONFIG_SYS_PCI0_MEM_BASE 0x80000000
	#define CONFIG_SYS_PCI0_MEM_SIZE _128M
	#define CONFIG_SYS_PCI1_MEM_BASE 0x88000000
	#define CONFIG_SYS_PCI1_MEM_SIZE _128M

	#define CONFIG_SYS_PCI0_0_MEM_SPACE (CONFIG_SYS_PCI0_MEM_BASE)
	#define CONFIG_SYS_PCI1_0_MEM_SPACE (CONFIG_SYS_PCI1_MEM_BASE)

	/* PCI I/O MAP section */
	#define CONFIG_SYS_PCI0_IO_BASE 0xfa000000
	#define CONFIG_SYS_PCI0_IO_SIZE _16M
	#define CONFIG_SYS_PCI1_IO_BASE 0xfb000000
	#define CONFIG_SYS_PCI1_IO_SIZE _16M

	#define CONFIG_SYS_PCI0_IO_SPACE (CONFIG_SYS_PCI0_IO_BASE)
	#define CONFIG_SYS_PCI0_IO_SPACE_PCI 0x00000000
	#define CONFIG_SYS_PCI1_IO_SPACE (CONFIG_SYS_PCI1_IO_BASE)
	#define CONFIG_SYS_PCI1_IO_SPACE_PCI 0x00000000

	#define CONFIG_SYS_ISA_IO_BASE_ADDRESS (CONFIG_SYS_PCI0_IO_BASE)
	#define CONFIG_SYS_PCI_IDSEL 0x30

	#undef CONFIG_BOOTARGS
	#define CONFIG_EXTRA_ENV_SETTINGS_COMMON \
	"netdev=eth0\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath}\0" \
	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	"addip=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}:${netdev}:off panic=1\0" \
	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
	"flash_nfs=run nfsargs addip addtty;" \
	"bootm ${kernel_addr}\0" \
	"flash_self=run ramargs addip addtty;" \
	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
	"bootm\0" \
	"rootpath=/opt/eldk/ppc_6xx\0" \
	"u-boot=p3mx/u-boot/u-boot.bin\0" \
	"load=tftp 100000 ${u-boot}\0" \
	"update=protect off fff00000 fff3ffff;era fff00000 fff3ffff;" \
	"cp.b 100000 fff00000 40000;" \
	"setenv filesize;saveenv\0" \
	"upd=run load update\0" \
	"serverip=11.0.0.152\0"

	#if defined (CONFIG_P3M750)
	#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_EXTRA_ENV_SETTINGS_COMMON \
	"hostname=p3m750\0" \
	"bootfile=/tftpboot/p3mx/vxWorks.st\0" \
	"kernel_addr=fc000000\0" \
	"ramdisk_addr=fc180000\0" \
	"vxfile=p3m750/vxWorks\0" \
	"vxuser=ddg\0" \
	"vxpass=ddg\0" \
	"vxtarget=target\0" \
	"vxflags=0x8\0" \
	"vxargs=setenv bootargs mgi(0,0)host:${vxfile} h=${serverip} " \
	"e=${ipaddr} u=${vxuser} pw=${vxpass} tn=${vxtarget} " \
	"f=${vxflags}\0"
	#elif defined (CONFIG_P3M7448)
	#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_EXTRA_ENV_SETTINGS_COMMON \
	"hostname=p3m7448\0"
	#endif

	#if defined (CONFIG_P3M750)
	#define CONFIG_BOOTCOMMAND "tftp;run vxargs;bootvx"
	#elif defined (CONFIG_P3M7448)
	#define CONFIG_BOOTCOMMAND " "
	#endif

	#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_SUBNETMASK
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_BOOTFILESIZE

	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_ASKENV
	#define CONFIG_CMD_DATE
	#define CONFIG_CMD_DIAG
	#define CONFIG_CMD_ELF
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_IRQ
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_NET
	#define CONFIG_CMD_NFS
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_REGINFO
	#define CONFIG_CMD_PCI
	#define CONFIG_CMD_CACHE
	#define CONFIG_CMD_SDRAM


	/*-----------------------------------------------------------------------
	* Miscellaneous configurable options
	----------------------------------------------------------------------/
	#define CONFIG_SYS_HUSH_PARSER

	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */

	#define CONFIG_SYS_LOAD_ADDR 0x08000000 /* default load address */

	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */

	#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
	#define CONFIG_LOOPW 1 /* enable loopw command */
	#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
	#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
	#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */

	/*-----------------------------------------------------------------------
	* Marvell MV64460 config settings
	----------------------------------------------------------------------/
	/* Reset values for Port behavior (8bit/ 32bit, etc.) only corrected device width */
	#if defined (CONFIG_P3M750)
	#define CONFIG_SYS_BOOT_PAR 0x8FDFF87F /* 16 bit flash, disable burst*/
	#elif defined (CONFIG_P3M7448)
	#define CONFIG_SYS_BOOT_PAR 0x8FEFFFFF /* 32 bit flash, burst enabled */
	#endif

	/*
	* MPP[0] Serial Port 0 TxD TxD OUT Connected to P14 (buffered)
	* MPP[1] Serial Port 0 RxD RxD IN Connected to P14 (buffered)
	* MPP[2] NC
	* MPP[3] Serial Port 1 TxD TxD OUT Connected to P14 (buffered)
	* MPP[4] PCI Monarch# GPIO IN Connected to P12
	* MPP[5] Serial Port 1 RxD RxD IN Connected to P14 (buffered)
	* MPP[6] PMC Carrier Interrupt 0 Int IN Connected to P14
	* MPP[7] PMC Carrier Interrupt 1 Int IN Connected to P14
	* MPP[8] Reserved Do not use
	* MPP[9] Reserved Do not use
	* MPP[10] Reserved Do not use
	* MPP[11] Reserved Do not use
	* MPP[12] Phy 0 Interrupt Int IN
	* MPP[13] Phy 1 Interrupt Int IN
	* MPP[14] NC
	* MPP[15] NC
	* MPP[16] PCI Interrupt C Int IN Connected to P11
	* MPP[17] PCI Interrupt D Int IN Connected to P11
	* MPP[18] Watchdog NMI# GPIO IN Connected to MPP[24]
	* MPP[19] Watchdog Expired# WDE OUT Connected to rst logic
	* MPP[20] Watchdog Status WD_STS IN Read back of rst by watchdog
	* MPP[21] NC
	* MPP[22] GP LED Green GPIO OUT
	* MPP[23] GP LED Red GPIO OUT
	* MPP[24] Watchdog NMI# Int OUT
	* MPP[25] NC
	* MPP[26] NC
	* MPP[27] PCI Interrupt A Int IN Connected to P11
	* MPP[28] NC
	* MPP[29] PCI Interrupt B Int IN Connected to P11
	* MPP[30] Module reset GPIO OUT Board reset
	* MPP[31] PCI EReady GPIO IN Connected to P12
	*/
	#define CONFIG_SYS_MPP_CONTROL_0 0x00303022
	#define CONFIG_SYS_MPP_CONTROL_1 0x00000000
	#define CONFIG_SYS_MPP_CONTROL_2 0x00004000
	#define CONFIG_SYS_MPP_CONTROL_3 0x00000004
	#define CONFIG_SYS_GPP_LEVEL_CONTROL 0x280730D0

	/*----------------------------------------------------------------------
	* Initial BAT mappings
	*/

	/* NOTES:
	* 1) GUARDED and WRITE_THRU not allowed in IBATS
	* 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT
	*/
	/* SDRAM */
	#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT0L (CONFIG_SYS_SDRAM_BASE \| BATL_PP_RW \| BATL_GUARDEDSTORAGE \| BATL_CACHEINHIBIT)
	#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U

	/* init ram */
	#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR \| BATL_PP_RW \| BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR \| BATU_BL_256K \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
	#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U

	/* PCI0, PCI1 in one BAT */
	#define CONFIG_SYS_IBAT2L BATL_NO_ACCESS
	#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U
	#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PCI0_MEM_BASE \| BATL_CACHEINHIBIT \| BATL_PP_RW \| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI0_MEM_BASE \| BATU_BL_256M \| BATU_VS \| BATU_VP)

	/* GT regs, bootrom, all the devices, PCI I/O */
	#define CONFIG_SYS_IBAT3L (CONFIG_SYS_MISC_REGION_BASE \| BATL_CACHEINHIBIT \| BATL_PP_RW)
	#define CONFIG_SYS_IBAT3U (CONFIG_SYS_MISC_REGION_BASE \| BATU_VS \| BATU_VP \| BATU_BL_256M)
	#define CONFIG_SYS_DBAT3L (CONFIG_SYS_MISC_REGION_BASE \| BATL_CACHEINHIBIT \| BATL_PP_RW \| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U

	#define CONFIG_SYS_IBAT4L (CONFIG_SYS_SDRAM1_BASE \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	#define CONFIG_SYS_IBAT4U (CONFIG_SYS_SDRAM1_BASE \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT4L (CONFIG_SYS_SDRAM1_BASE \| BATL_PP_RW \| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U

	/* set rest out of range for Linux !!!!!!!!!!! */

	/* IBAT5 and DBAT5 */
	#define CONFIG_SYS_IBAT5L (0x20000000 \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	#define CONFIG_SYS_IBAT5U (0x20000000 \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT5L (0x20000000 \| BATL_PP_RW \| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U

	/* IBAT6 and DBAT6 */
	#define CONFIG_SYS_IBAT6L (0x20000000 \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	#define CONFIG_SYS_IBAT6U (0x20000000 \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT6L (0x20000000 \| BATL_PP_RW \| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U

	/* IBAT7 and DBAT7 */
	#define CONFIG_SYS_IBAT7L (0x20000000 \| BATL_PP_RW \| BATL_CACHEINHIBIT)
	#define CONFIG_SYS_IBAT7U (0x20000000 \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT7L (0x20000000 \| BATL_PP_RW \| BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (8<<20) /* Initial Memory map for Linux */
	#define CONFIG_SYS_VXWORKS_MAC_PTR 0x42010000 /* use some memory in SRAM that's not used!!! */

	/*-----------------------------------------------------------------------
	* Cache Configuration
	*/
	#define CONFIG_SYS_CACHELINE_SIZE 32 /* For all MPC74xx CPUs */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
	#endif

	/*-----------------------------------------------------------------------
	* L2CR setup -- make sure this is right for your board!
	* look in include/mpc74xx.h for the defines used here
	*/
	#define CONFIG_SYS_L2

	#if defined (CONFIG_750CX) \|\| defined (CONFIG_750FX)
	#define L2_INIT 0
	#else
	#define L2_INIT (L2CR_L2SIZ_2M \| L2CR_L2CLK_3 \| L2CR_L2RAM_BURST \| \
	L2CR_L2OH_5 \| L2CR_L2CTL \| L2CR_L2WT)
	#endif

	#define L2_ENABLE (L2_INIT \| L2CR_L2E)

	#ifndef __ASSEMBLY__
	#include <../board/Marvell/include/core.h>
	#endif

	#endif /* __CONFIG_H */