ARM: imx: Decouple mccmon6's SPL and u-boot proper code
The mccmon6 has been used a "mixed" approach between SPL and
U-Boot proper sources.
This commit decoupes SPL and u-boot proper, which allows clear
distinction between those two code bases and facilitates
conversion to DM/DTS on this particular board.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
diff --git a/board/liebherr/mccmon6/Makefile b/board/liebherr/mccmon6/Makefile
index ead6750..3c9786c 100644
--- a/board/liebherr/mccmon6/Makefile
+++ b/board/liebherr/mccmon6/Makefile
@@ -2,5 +2,8 @@
#
# (C) Copyright 2016-2017
# Lukasz Majewski, DENX Software Engineering, lukma@denx.de
-
-obj-y := mccmon6.o spl.o
+ifdef CONFIG_SPL_BUILD
+obj-y := spl.o
+else
+obj-y := mccmon6.o
+endif
diff --git a/board/liebherr/mccmon6/mccmon6.c b/board/liebherr/mccmon6/mccmon6.c
index 3b7e89f..6a5fbbb 100644
--- a/board/liebherr/mccmon6/mccmon6.c
+++ b/board/liebherr/mccmon6/mccmon6.c
@@ -9,37 +9,11 @@
#include <asm/arch/clock.h>
#include <asm/arch/iomux.h>
#include <asm/arch/imx-regs.h>
-#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/boot_mode.h>
-#include <asm/io.h>
-#include <fsl_esdhc_imx.h>
-#include <mmc.h>
-#include <netdev.h>
-#include <phy.h>
-#include <input.h>
-#include <spl.h>
DECLARE_GLOBAL_DATA_PTR;
-#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
- PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
- PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define WEIM_NOR_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-
-#define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4)
-#define NOR_WP IMX_GPIO_NR(1, 1)
-#define DISPLAY_EN IMX_GPIO_NR(1, 2)
-
int dram_init(void)
{
gd->ram_size = imx_ddr_size();
@@ -47,198 +21,11 @@
return 0;
}
-static iomux_v3_cfg_t const uart1_pads[] = {
- IOMUX_PADS(PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
- IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
-};
-
-static iomux_v3_cfg_t const usdhc2_pads[] = {
- IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- /* Carrier MicroSD Card Detect */
- IOMUX_PADS(PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
-static iomux_v3_cfg_t const usdhc3_pads[] = {
- IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
-};
-
-static void setup_iomux_uart(void)
-{
- SETUP_IOMUX_PADS(uart1_pads);
-}
-
-static struct fsl_esdhc_cfg usdhc_cfg[2] = {
- {USDHC3_BASE_ADDR},
- {USDHC2_BASE_ADDR},
-};
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int ret = 0;
-
- switch (cfg->esdhc_base) {
- case USDHC2_BASE_ADDR:
- ret = !gpio_get_value(USDHC2_CD_GPIO);
- break;
- case USDHC3_BASE_ADDR:
- /*
- * eMMC don't have card detect pin - since it is soldered to the
- * PCB board
- */
- ret = 1;
- break;
- }
- return ret;
-}
-
-int board_mmc_init(bd_t *bis)
-{
- int ret;
- u32 index = 0;
-
- /*
- * MMC MAP
- * (U-Boot device node) (Physical Port)
- * mmc0 Soldered on board eMMC device
- * mmc1 MicroSD card
- */
- for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
- switch (index) {
- case 0:
- SETUP_IOMUX_PADS(usdhc3_pads);
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- usdhc_cfg[0].max_bus_width = 8;
- break;
- case 1:
- SETUP_IOMUX_PADS(usdhc2_pads);
- usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
- usdhc_cfg[1].max_bus_width = 4;
- gpio_direction_input(USDHC2_CD_GPIO);
- break;
- default:
- printf("Warning: More USDHC controllers (%d) than supported (%d)\n",
- index + 1, CONFIG_SYS_FSL_USDHC_NUM);
- return -EINVAL;
- }
-
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
- if (ret)
- return ret;
- }
-
- return 0;
-}
-
-static iomux_v3_cfg_t const eimnor_pads[] = {
- IOMUX_PADS(PAD_EIM_D16__EIM_DATA16 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D17__EIM_DATA17 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D18__EIM_DATA18 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D19__EIM_DATA19 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D20__EIM_DATA20 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D21__EIM_DATA21 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D22__EIM_DATA22 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D23__EIM_DATA23 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D24__EIM_DATA24 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D25__EIM_DATA25 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D26__EIM_DATA26 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D27__EIM_DATA27 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D28__EIM_DATA28 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D29__EIM_DATA29 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D30__EIM_DATA30 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D31__EIM_DATA31 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA0__EIM_AD00 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA1__EIM_AD01 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA2__EIM_AD02 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA3__EIM_AD03 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA4__EIM_AD04 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA5__EIM_AD05 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA6__EIM_AD06 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA7__EIM_AD07 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA8__EIM_AD08 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA9__EIM_AD09 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA10__EIM_AD10 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA11__EIM_AD11 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA12__EIM_AD12 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA13__EIM_AD13 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA14__EIM_AD14 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_DA15__EIM_AD15 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_A16__EIM_ADDR16 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_A17__EIM_ADDR17 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_A18__EIM_ADDR18 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_A19__EIM_ADDR19 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_A20__EIM_ADDR20 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_A21__EIM_ADDR21 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_A22__EIM_ADDR22 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_A23__EIM_ADDR23 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_A24__EIM_ADDR24 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_A25__EIM_ADDR25 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_OE__EIM_OE_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_RW__EIM_RW | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_CS0__EIM_CS0_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
-static void eimnor_cs_setup(void)
-{
- struct weim *weim_regs = (struct weim *)WEIM_BASE_ADDR;
-
-
- /* NOR configuration */
- writel(0x00620181, &weim_regs->cs0gcr1);
- writel(0x00000001, &weim_regs->cs0gcr2);
- writel(0x0b020000, &weim_regs->cs0rcr1);
- writel(0x0000b000, &weim_regs->cs0rcr2);
- writel(0x0804a240, &weim_regs->cs0wcr1);
- writel(0x00000000, &weim_regs->cs0wcr2);
-
- writel(0x00000120, &weim_regs->wcr);
- writel(0x00000010, &weim_regs->wiar);
- writel(0x00000000, &weim_regs->ear);
-
- set_chipselect_size(CS0_128);
-}
-
-static void setup_eimnor(void)
-{
- SETUP_IOMUX_PADS(eimnor_pads);
- gpio_direction_output(NOR_WP, 1);
-
- enable_eim_clk(1);
- eimnor_cs_setup();
-}
-
-int board_early_init_f(void)
-{
- setup_iomux_uart();
-
- return 0;
-}
-
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
- gpio_direction_output(DISPLAY_EN, 1);
-
- setup_eimnor();
-
return 0;
}
@@ -255,75 +42,3 @@
return 0;
}
-
-#ifdef CONFIG_SPL_BOARD_INIT
-void spl_board_init(void)
-{
- setup_eimnor();
-
- gpio_direction_output(DISPLAY_EN, 1);
-}
-#endif /* CONFIG_SPL_BOARD_INIT */
-
-#ifdef CONFIG_SPL_BUILD
-void board_boot_order(u32 *spl_boot_list)
-{
- switch (spl_boot_device()) {
- case BOOT_DEVICE_MMC2:
- case BOOT_DEVICE_MMC1:
- spl_boot_list[0] = BOOT_DEVICE_MMC2;
- spl_boot_list[1] = BOOT_DEVICE_MMC1;
- break;
-
- case BOOT_DEVICE_NOR:
- spl_boot_list[0] = BOOT_DEVICE_NOR;
- break;
- }
-}
-#endif /* CONFIG_SPL_BUILD */
-
-#ifdef CONFIG_SPL_OS_BOOT
-int spl_start_uboot(void)
-{
- char s[16];
- int ret;
- /*
- * We use BOOT_DEVICE_MMC1, but SD card is connected
- * to MMC2
- *
- * Correct "mapping" is delivered in board defined
- * board_boot_order() function.
- *
- * SD card boot is regarded as a "development" one,
- * hence we _always_ go through the u-boot.
- *
- */
- if (spl_boot_device() == BOOT_DEVICE_MMC1)
- return 1;
-
- /* break into full u-boot on 'c' */
- if (serial_tstc() && serial_getc() == 'c')
- return 1;
-
- env_init();
- ret = env_get_f("boot_os", s, sizeof(s));
- if ((ret != -1) && (strcmp(s, "no") == 0))
- return 1;
-
- /*
- * Check if SWUpdate recovery needs to be started
- *
- * recovery_status = NULL (not set - ret == -1) -> normal operation
- *
- * recovery_status = progress or
- * recovery_status = failed or
- * recovery_status = <any value> -> start SWUpdate
- *
- */
- ret = env_get_f("recovery_status", s, sizeof(s));
- if (ret != -1)
- return 1;
-
- return 0;
-}
-#endif /* CONFIG_SPL_OS_BOOT */
diff --git a/board/liebherr/mccmon6/spl.c b/board/liebherr/mccmon6/spl.c
index f0ed78c..4f1e240 100644
--- a/board/liebherr/mccmon6/spl.c
+++ b/board/liebherr/mccmon6/spl.c
@@ -20,7 +20,6 @@
#include <asm/arch/sys_proto.h>
#include <spl.h>
-#if defined(CONFIG_SPL_BUILD)
#include <asm/arch/mx6-ddr.h>
/*
* Driving strength:
@@ -274,6 +273,25 @@
udelay(100);
}
+static void setup_spi(void)
+{
+ enable_spi_clk(true, 2);
+}
+
+#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+ IOMUX_PADS(PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+ IOMUX_PADS(PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+};
+
+static void setup_iomux_uart(void)
+{
+ SETUP_IOMUX_PADS(uart1_pads);
+}
+
void board_init_f(ulong dummy)
{
ccgr_init();
@@ -284,7 +302,7 @@
gpr_init();
/* iomux */
- board_early_init_f();
+ setup_iomux_uart();
/* setup GP timer */
timer_init();
@@ -292,7 +310,257 @@
/* UART clocks enabled and gd valid - init serial console */
preloader_console_init();
+ /* enable ECSPI clocks */
+ setup_spi();
+
/* DDR initialization */
spl_dram_init();
}
+
+void board_boot_order(u32 *spl_boot_list)
+{
+ switch (spl_boot_device()) {
+ case BOOT_DEVICE_MMC2:
+ case BOOT_DEVICE_MMC1:
+ spl_boot_list[0] = BOOT_DEVICE_MMC2;
+ spl_boot_list[1] = BOOT_DEVICE_MMC1;
+ break;
+
+ case BOOT_DEVICE_NOR:
+ spl_boot_list[0] = BOOT_DEVICE_NOR;
+ break;
+ }
+}
+
+#ifdef CONFIG_SPL_OS_BOOT
+int spl_start_uboot(void)
+{
+ char s[16];
+ int ret;
+ /*
+ * We use BOOT_DEVICE_MMC1, but SD card is connected
+ * to MMC2
+ *
+ * Correct "mapping" is delivered in board defined
+ * board_boot_order() function.
+ *
+ * SD card boot is regarded as a "development" one,
+ * hence we _always_ go through the u-boot.
+ *
+ */
+ if (spl_boot_device() == BOOT_DEVICE_MMC1)
+ return 1;
+
+ /* break into full u-boot on 'c' */
+ if (serial_tstc() && serial_getc() == 'c')
+ return 1;
+
+ env_init();
+ ret = env_get_f("boot_os", s, sizeof(s));
+ if ((ret != -1) && (strcmp(s, "no") == 0))
+ return 1;
+
+ /*
+ * Check if SWUpdate recovery needs to be started
+ *
+ * recovery_status = NULL (not set - ret == -1) -> normal operation
+ *
+ * recovery_status = progress or
+ * recovery_status = failed or
+ * recovery_status = <any value> -> start SWUpdate
+ *
+ */
+ ret = env_get_f("recovery_status", s, sizeof(s));
+ if (ret != -1)
+ return 1;
+
+ return 0;
+}
+#endif /* CONFIG_SPL_OS_BOOT */
+
+#define WEIM_NOR_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define NOR_WP IMX_GPIO_NR(1, 1)
+
+static iomux_v3_cfg_t const eimnor_pads[] = {
+ IOMUX_PADS(PAD_EIM_D16__EIM_DATA16 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D17__EIM_DATA17 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D18__EIM_DATA18 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D19__EIM_DATA19 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D20__EIM_DATA20 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D21__EIM_DATA21 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D22__EIM_DATA22 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D23__EIM_DATA23 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D24__EIM_DATA24 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D25__EIM_DATA25 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D26__EIM_DATA26 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D27__EIM_DATA27 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D28__EIM_DATA28 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D29__EIM_DATA29 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D30__EIM_DATA30 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D31__EIM_DATA31 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA0__EIM_AD00 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA1__EIM_AD01 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA2__EIM_AD02 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA3__EIM_AD03 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA4__EIM_AD04 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA5__EIM_AD05 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA6__EIM_AD06 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA7__EIM_AD07 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA8__EIM_AD08 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA9__EIM_AD09 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA10__EIM_AD10 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA11__EIM_AD11 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA12__EIM_AD12 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA13__EIM_AD13 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA14__EIM_AD14 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_DA15__EIM_AD15 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A16__EIM_ADDR16 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A17__EIM_ADDR17 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A18__EIM_ADDR18 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A19__EIM_ADDR19 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A20__EIM_ADDR20 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A21__EIM_ADDR21 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A22__EIM_ADDR22 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A23__EIM_ADDR23 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A24__EIM_ADDR24 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A25__EIM_ADDR25 | MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_OE__EIM_OE_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_RW__EIM_RW | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_CS0__EIM_CS0_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+};
+
+static void eimnor_cs_setup(void)
+{
+ struct weim *weim_regs = (struct weim *)WEIM_BASE_ADDR;
+
+ /* NOR configuration */
+ writel(0x00620181, &weim_regs->cs0gcr1);
+ writel(0x00000001, &weim_regs->cs0gcr2);
+ writel(0x0b020000, &weim_regs->cs0rcr1);
+ writel(0x0000b000, &weim_regs->cs0rcr2);
+ writel(0x0804a240, &weim_regs->cs0wcr1);
+ writel(0x00000000, &weim_regs->cs0wcr2);
+
+ writel(0x00000120, &weim_regs->wcr);
+ writel(0x00000010, &weim_regs->wiar);
+ writel(0x00000000, &weim_regs->ear);
+
+ set_chipselect_size(CS0_128);
+}
+
+static void setup_eimnor(void)
+{
+ SETUP_IOMUX_PADS(eimnor_pads);
+ gpio_direction_output(NOR_WP, 1);
+
+ enable_eim_clk(1);
+ eimnor_cs_setup();
+}
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4)
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+ IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ /* Carrier MicroSD Card Detect */
+ IOMUX_PADS(PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+ IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+ IOMUX_PADS(PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+};
+
+static struct fsl_esdhc_cfg usdhc_cfg[2] = {
+ {USDHC3_BASE_ADDR},
+ {USDHC2_BASE_ADDR},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+ int ret = 0;
+
+ switch (cfg->esdhc_base) {
+ case USDHC2_BASE_ADDR:
+ ret = !gpio_get_value(USDHC2_CD_GPIO);
+ break;
+ case USDHC3_BASE_ADDR:
+ /*
+ * eMMC don't have card detect pin - since it is soldered to the
+ * PCB board
+ */
+ ret = 1;
+ break;
+ }
+ return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ int ret;
+ u32 index = 0;
+
+ /*
+ * MMC MAP
+ * (U-Boot device node) (Physical Port)
+ * mmc0 Soldered on board eMMC device
+ * mmc1 MicroSD card
+ */
+ for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
+ switch (index) {
+ case 0:
+ SETUP_IOMUX_PADS(usdhc3_pads);
+ usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+ usdhc_cfg[0].max_bus_width = 8;
+ break;
+ case 1:
+ SETUP_IOMUX_PADS(usdhc2_pads);
+ usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+ usdhc_cfg[1].max_bus_width = 4;
+ gpio_direction_input(USDHC2_CD_GPIO);
+ break;
+ default:
+ printf("Warning: More USDHC controllers (%d) than supported (%d)\n",
+ index + 1, CONFIG_SYS_FSL_USDHC_NUM);
+ return -EINVAL;
+ }
+
+ ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_SPL_BOARD_INIT
+#define DISPLAY_EN IMX_GPIO_NR(1, 2)
+void spl_board_init(void)
+{
+ setup_eimnor();
+
+ gpio_direction_output(DISPLAY_EN, 1);
+}
-#endif
+#endif /* CONFIG_SPL_BOARD_INIT */