CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_SYS_TEXT_BASE=0x26f00000
CONFIG_TARGET_SAMA5D4EK=y
CONFIG_SPL_GPIO_SUPPORT=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
CONFIG_SPL=y
CONFIG_DEBUG_UART_BOARD_INIT=y
CONFIG_DEBUG_UART_BASE=0xfc00c000
CONFIG_DEBUG_UART_CLOCK=88000000
CONFIG_SPL_SPI_FLASH_SUPPORT=y
CONFIG_SPL_SPI_SUPPORT=y
CONFIG_DEBUG_UART=y
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_FIT=y
CONFIG_SPI_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,768k(uboot)ro,256K(env_redundant),256k(env),512k(dtb),6M(kernel)ro,-(rootfs) rootfstype=ubifs ubi.mtd=6 root=ubi0:rootfs"
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_SPL_SPI_LOAD=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMI is not set
# CONFIG_CMD_FLASH is not set
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_MMC=y
CONFIG_CMD_NAND=y
CONFIG_CMD_SF=y
CONFIG_CMD_USB=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_FAT=y
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d4ek"
CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-parent dma-names dmas"
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_DM=y
CONFIG_SPL_DM=y
CONFIG_SPL_DM_SEQ_ALIAS=y
CONFIG_CLK=y
CONFIG_SPL_CLK=y
CONFIG_CLK_AT91=y
CONFIG_AT91_UTMI=y
CONFIG_AT91_H32MX=y
CONFIG_DM_GPIO=y
CONFIG_AT91_GPIO=y
CONFIG_DM_MMC=y
CONFIG_GENERIC_ATMEL_MCI=y
CONFIG_NAND=y
CONFIG_NAND_ATMEL=y
CONFIG_PMECC_CAP=8
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_ATMEL=y
CONFIG_DM_ETH=y
CONFIG_MACB=y
CONFIG_PINCTRL=y
CONFIG_SPL_PINCTRL=y
CONFIG_PINCTRL_AT91=y
CONFIG_DM_SERIAL=y
CONFIG_DEBUG_UART_ATMEL=y
CONFIG_DEBUG_UART_ANNOUNCE=y
CONFIG_ATMEL_USART=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_TIMER=y
CONFIG_SPL_TIMER=y
CONFIG_ATMEL_PIT_TIMER=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_ATMEL_USBA=y
CONFIG_DM_VIDEO=y
CONFIG_ATMEL_HLCD=y