power: pmic: sunxi: add AXP717 SPL support
On boards using the AXP717 PMIC, the DRAM rail is often not setup
correctly at reset time, so we have to program the PMIC very early in
the SPL, before running the DRAM initialisation.
Using the new generic AXP SPL driver, add the Kconfig options and
platform bits needed to support an AXP717 PMIC chip in I2C mode.
This allows to set up the correct voltage for the DRAM chips and the
CPU cores.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Ryan Walklin <ryan@testtoast.com>
diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index 33b8bc1..5556a22 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -109,6 +109,13 @@
Select this to enable support for the AXP313 PMIC found on some
H616 boards.
+config AXP717_POWER
+ bool "axp717 pmic support"
+ select AXP_PMIC_BUS
+ select CMD_POWEROFF
+ ---help---
+ Select this to enable support for the AXP717 PMIC found on some boards.
+
config AXP809_POWER
bool "axp809 pmic support"
depends on MACH_SUN9I
@@ -151,10 +158,11 @@
config AXP_DCDC2_VOLT
int "axp pmic dcdc2 voltage"
- depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER || AXP313_POWER
+ depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER || AXP313_POWER || AXP717_POWER
default 900 if AXP818_POWER
default 1400 if AXP152_POWER || AXP209_POWER
default 1000 if AXP313_POWER
+ default 1000 if AXP717_POWER
default 1200 if MACH_SUN6I
default 1100 if MACH_SUN8I
default 0 if MACH_SUN9I
@@ -167,11 +175,11 @@
On A80 boards dcdc2 powers the GPU and can be left off.
On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
On R40 boards dcdc2 is VDD-CPU and should be 1.1V
- On boards using the AXP313 it's often VDD-CPU.
+ On boards using the AXP313 or AXP717 it's often VDD-CPU.
config AXP_DCDC3_VOLT
int "axp pmic dcdc3 voltage"
- depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER || AXP313_POWER
+ depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER || AXP313_POWER || AXP717_POWER
default 900 if AXP809_POWER || AXP818_POWER
default 1500 if AXP152_POWER
default 1250 if AXP209_POWER
@@ -188,7 +196,8 @@
On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V.
On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V.
- On boards using the AXP313 it's often VDD-DRAM and should be 1.1V for LPDDR4.
+ On boards using the AXP313 or AXP717 it's often VDD-DRAM and should
+ be 1.1V for LPDDR4.
config AXP_DCDC4_VOLT
int "axp pmic dcdc4 voltage"