ARM: keystone2: Use dtb images by default
Now that OF_CONTROL is enabled on all keystone2 platforms,
build the default images with DT.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
diff --git a/arch/arm/mach-keystone/config.mk b/arch/arm/mach-keystone/config.mk
index ceacffa..9ae1e9a 100644
--- a/arch/arm/mach-keystone/config.mk
+++ b/arch/arm/mach-keystone/config.mk
@@ -16,13 +16,13 @@
OBJCOPYFLAGS_u-boot-spi.gph = -I binary -O binary --pad-to=$(CONFIG_SPL_PAD_TO) \
--gap-fill=0
-u-boot-spi.gph: spl/u-boot-spl.gph u-boot.img FORCE
+u-boot-spi.gph: spl/u-boot-spl.gph u-boot-dtb.img FORCE
$(call if_changed,pad_cat)
ifndef CONFIG_SPL_BUILD
MKIMAGEFLAGS_MLO = -A $(ARCH) -T gpimage -C none \
-a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_TEXT_BASE) -n U-Boot
-MLO: u-boot.bin FORCE
+MLO: u-boot-dtb.bin FORCE
$(call if_changed,mkimage)
@dd if=/dev/zero bs=8 count=1 2>/dev/null >> $@
endif
diff --git a/board/ti/ks2_evm/README b/board/ti/ks2_evm/README
index b8d55e7..0fe5c3b 100644
--- a/board/ti/ks2_evm/README
+++ b/board/ti/ks2_evm/README
@@ -59,8 +59,8 @@
- UART boot
Supported image formats:
- - u-boot.bin: for loading and running u-boot.bin through Texas instruments
- code composure studio (CCS) and for UART boot.
+ - u-boot-dtb.bin: for loading and running u-boot-dtb.bin through
+ Texas Instruments code composure studio (CCS) and for UART boot.
- u-boot-spi.gph: gpimage for programming SPI NOR flash for SPI NOR boot
- MLO: gpimage for programming AEMIF NAND flash for NAND boot
@@ -69,18 +69,18 @@
Examples for k2hk, for k2e and k2l just replace k2hk prefix accordingly.
Don't forget to add ARCH=arm and CROSS_COMPILE.
-To build u-boot.bin, u-boot-spi.gph, MLO:
+To build u-boot-dtb.bin, u-boot-spi.gph, MLO:
>make k2hk_evm_defconfig
>make
Load and Run U-Boot on keystone EVMs using CCS
=========================================
-Need Code Composer Studio (CCS) installed on a PC to load and run u-boot.bin
+Need Code Composer Studio (CCS) installed on a PC to load and run u-boot-dtb.bin
on EVM. See instructions at below link for installing CCS on a Windows PC.
http://processors.wiki.ti.com/index.php/MCSDK_UG_Chapter_Getting_Started#
Installing_Code_Composer_Studio
-Use u-boot.bin from the build folder for loading and running u-boot binary
+Use u-boot-dtb.bin from the build folder for loading and running u-boot binary
on EVM. Follow instructions at
K2HK http://processors.wiki.ti.com/index.php/EVMK2H_Hardware_Setup
K2E http://processors.wiki.ti.com/index.php/EVMK2E_Hardware_Setup
@@ -100,7 +100,7 @@
is connected: Unknown)" at the debug window (This is created once Target
configuration is launched) and select "Connect Target".
2. Once target connect is successful, choose Tools->Load Memory option from the
- top level menu. At the Load Memory window, choose the file u-boot.bin
+ top level menu. At the Load Memory window, choose the file u-boot-dtb.bin
through "Browse" button and click "next >" button. In the next window, enter
Start address as 0xc001000, choose Type-size "32 bits" and click "Finish"
button.
@@ -167,7 +167,7 @@
Open BMC and regular UART terminals.
-1. On the regular UART port start xmodem transfer of the u-boot.bin
+1. On the regular UART port start xmodem transfer of the u-boot-dtb.bin
2. Using BMC terminal set the ARM-UART bootmode and reboot the EVM
BMC> bootmode #4
MBC> reboot