ARM: mxs: Consolidate configuration options
Pull all the duplicate configuration options into configs/mxs.h
from the board configuration files. This reduces the files greatly
and makes them somewhat more readable. Besides, we do no longer
have such a horrible duplication of code.
Note that the mx23evk grew in size slightly. This is due to the
CONFIG_SYS_CBSIZE now being set to 1024 as it is on the rest of
MXS systems.
This patch also fixes the OCRAM size for i.MX23. The i.MX23 has
only 32kB of OCRAM, while i.MX28 has 128kB of OCRAM.
I verified the configuration didn't change for each of the boards,
but I didn't boot-test it on the boards I do not have. I configured
U-Boot for each board using the "make ... <board>_config" command
and then ran "cpp -I include -dM include/config.h" , which dumped
all the configuration options. I did this both before and after this
patch and finally compared the results for each MXS board. Actually,
the results do differ slightly, since the configs/mxs.h file now
properly includes the correct iomux-mx23.h or iomux-mx28.h , so
while comparing, I had to ignore these new defines. These have no
impact on U-Boot configuration though.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h
index de69182..877b811 100644
--- a/include/configs/mx28evk.h
+++ b/include/configs/mx28evk.h
@@ -16,33 +16,16 @@
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
-#ifndef __MX28EVK_CONFIG_H__
-#define __MX28EVK_CONFIG_H__
+#ifndef __CONFIGS_MX28EVK_H__
+#define __CONFIGS_MX28EVK_H__
-/* SoC configurations */
+/* System configurations */
#define CONFIG_MX28 /* i.MX28 SoC */
-
-#define CONFIG_MXS_GPIO /* GPIO control */
-#define CONFIG_SYS_HZ 1000 /* Ticks per second */
-
#define CONFIG_MACH_TYPE MACH_TYPE_MX28EVK
-
-#include <asm/arch/regs-base.h>
-
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_ARCH_MISC_INIT
-
-/* SPL */
-#define CONFIG_SPL
-#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
-#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs"
-#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds"
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_GPIO_SUPPORT
+#define CONFIG_SYS_PROMPT "MX28EVK U-Boot > "
/* U-Boot Commands */
+#define CONFIG_SYS_NO_FLASH
#include <config_cmd_default.h>
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DOS_PARTITION
@@ -57,6 +40,7 @@
#define CONFIG_CMD_NET
#define CONFIG_CMD_NFS
#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVEENV
#define CONFIG_CMD_SETEXPR
#define CONFIG_CMD_SF
#define CONFIG_CMD_SPI
@@ -66,81 +50,24 @@
#define CONFIG_CMD_NAND_TRIMFFS
#define CONFIG_VIDEO
-/* Memory configurations */
+/* Memory configuration */
#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */
#define PHYS_SDRAM_1 0x40000000 /* Base address */
#define PHYS_SDRAM_1_SIZE 0x40000000 /* Max 1 GB RAM */
-#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */
-#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */
-#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-/* Point initial SP in SRAM so SPL can use it too. */
-
-#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000
-#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024)
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-/*
- * We need to sacrifice first 4 bytes of RAM here to avoid triggering some
- * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot
- * binary. In case there was more of this mess, 0x100 bytes are skipped.
- */
-#define CONFIG_SYS_TEXT_BASE 0x40000100
-
+/* Environment */
+#define CONFIG_ENV_SIZE (16 * 1024)
#define CONFIG_ENV_OVERWRITE
-/* U-Boot general configurations */
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_PROMPT "MX28EVK U-Boot > "
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */
-#define CONFIG_SYS_PBSIZE \
- (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
- /* Print buffer size */
-#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
- /* Boot argument buffer size */
-#define CONFIG_VERSION_VARIABLE /* U-BOOT version */
-#define CONFIG_AUTO_COMPLETE /* Command auto complete */
-#define CONFIG_CMDLINE_EDITING /* Command history etc */
-#define CONFIG_SYS_HUSH_PARSER
-
-/* Serial Driver */
-#define CONFIG_PL011_SERIAL
-#define CONFIG_PL011_CLOCK 24000000
-#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE }
-#define CONFIG_CONS_INDEX 0
-#define CONFIG_BAUDRATE 115200 /* Default baud rate */
-
-/* DMA */
-#define CONFIG_APBH_DMA
-/* MMC Driver */
-#ifdef CONFIG_ENV_IS_IN_MMC
- #define CONFIG_ENV_OFFSET (256 * 1024)
- #define CONFIG_ENV_SIZE (16 * 1024)
- #define CONFIG_SYS_MMC_ENV_DEV 0
+/* Environment is in MMC */
+#if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC)
+#define CONFIG_ENV_OFFSET (256 * 1024)
+#define CONFIG_SYS_MMC_ENV_DEV 0
#endif
-#define CONFIG_CMD_SAVEENV
-#ifdef CONFIG_CMD_MMC
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_BOUNCE_BUFFER
-#define CONFIG_MXS_MMC
-#endif
-
-/* NAND Driver */
-#define CONFIG_ENV_SIZE (16 * 1024)
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_MXS
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x60000000
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE
/* Environment is in NAND */
-#ifdef CONFIG_ENV_IS_IN_NAND
+#if defined(CONFIG_CMD_NAND) && defined(CONFIG_ENV_IS_IN_NAND)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
#define CONFIG_ENV_SECT_SIZE (128 * 1024)
#define CONFIG_ENV_RANGE (512 * 1024)
@@ -149,6 +76,21 @@
(CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)
#endif
+/* Environemnt is in SPI flash */
+#if defined(CONFIG_CMD_SF) && defined(CONFIG_ENV_IS_IN_SPI_FLASH)
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_SIZE 0x1000 /* 4KB */
+#define CONFIG_ENV_OFFSET 0x40000 /* 256K */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SECT_SIZE 0x1000
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_BUS 2
+#define CONFIG_ENV_SPI_MAX_HZ 24000000
+#define CONFIG_ENV_SPI_MODE SPI_MODE_0
+#endif
+
+/* UBI and NAND partitioning */
+#ifdef CONFIG_CMD_NAND
#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#define CONFIG_CMD_MTDPARTS
@@ -168,13 +110,10 @@
"-(filesystem)"
#endif
-/* Ethernet on SOC (FEC) */
+/* FEC Ethernet on SoC */
#ifdef CONFIG_CMD_NET
-#define CONFIG_NET_MULTI
-#define CONFIG_ETHPRIME "FEC0"
#define CONFIG_FEC_MXC
-#define CONFIG_MII
-#define CONFIG_FEC_XCV_TYPE RMII
+#define CONFIG_NET_MULTI
#define CONFIG_MX28_FEC_MAC_IN_OCOTP
#endif
@@ -185,65 +124,35 @@
/* USB */
#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI
-#define CONFIG_USB_EHCI_MXS
#define CONFIG_EHCI_MXS_PORT1
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
-#define CONFIG_EHCI_IS_TDI
#define CONFIG_USB_STORAGE
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_USB_ETHER_SMSC95XX
#endif
-/* I2C */
-#ifdef CONFIG_CMD_I2C
-#define CONFIG_I2C_MXS
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED 400000
-#endif
-
/* SPI */
#ifdef CONFIG_CMD_SPI
-#define CONFIG_HARD_SPI
-#define CONFIG_MXS_SPI
-#define CONFIG_SPI_HALF_DUPLEX
#define CONFIG_DEFAULT_SPI_BUS 2
#define CONFIG_DEFAULT_SPI_MODE SPI_MODE_0
/* SPI Flash */
#ifdef CONFIG_CMD_SF
#define CONFIG_SPI_FLASH
-#define CONFIG_SF_DEFAULT_BUS 2
-#define CONFIG_SF_DEFAULT_CS 0
+#define CONFIG_SF_DEFAULT_BUS 2
+#define CONFIG_SF_DEFAULT_CS 0
/* this may vary and depends on the installed chip */
#define CONFIG_SPI_FLASH_SST
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#define CONFIG_SF_DEFAULT_SPEED 24000000
-
-/* (redundant) environemnt in SPI flash */
-#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
-#define CONFIG_ENV_SIZE 0x1000 /* 4KB */
-#define CONFIG_ENV_OFFSET 0x40000 /* 256K */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
-#define CONFIG_ENV_SECT_SIZE 0x1000
-#define CONFIG_ENV_SPI_CS 0
-#define CONFIG_ENV_SPI_BUS 2
-#define CONFIG_ENV_SPI_MAX_HZ 24000000
-#define CONFIG_ENV_SPI_MODE SPI_MODE_0
#endif
-#endif
+
#endif
/* Framebuffer support */
#ifdef CONFIG_VIDEO
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_MXS
#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define CONFIG_SPLASH_SCREEN
#define CONFIG_CMD_BMP
#define CONFIG_BMP_16BPP
@@ -253,15 +162,12 @@
#endif
/* Boot Linux */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_BOOTDELAY 1
-#define CONFIG_BOOTFILE "uImage"
-#define CONFIG_LOADADDR 0x42000000
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_LOADADDR 0x42000000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
-#define CONFIG_OF_LIBFDT
-/* Extra Environments */
+/* Extra Environment */
#define CONFIG_EXTRA_ENV_SETTINGS \
"update_nand_full_filename=u-boot.nand\0" \
"update_nand_firmware_filename=u-boot.sb\0" \
@@ -372,4 +278,7 @@
"fi; " \
"else run netboot; fi"
-#endif /* __MX28EVK_CONFIG_H__ */
+/* The rest of the configuration is shared */
+#include <configs/mxs.h>
+
+#endif /* __CONFIGS_MX28EVK_H__ */