diff --git a/CHANGELOG b/CHANGELOG
index 32110df..b5a918d 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -2,6 +2,13 @@
 Changes since U-Boot 1.0.1:
 ======================================================================
 
+* Add variable CPU clock for MPC859/866 systems (so far only TQM866M):
+  see doc/README.MPC866 for details;
+  implement workaround for "SIU4" and "SIU9" silicon bugs on MPC866;
+  calculate CPU clock frequency from PLL register values.
+
+* Add support for 128 MB RAM on TQM8xxL/M modules
+
 * Fix PS/2 keyboard problem caused by statically initialized variable
   pointing to a location in flash
 
diff --git a/Makefile b/Makefile
index 7062163..0a5b470 100644
--- a/Makefile
+++ b/Makefile
@@ -483,11 +483,7 @@
 TQM862M_66MHz_config	\
 TQM862M_80MHz_config	\
 TQM862M_100MHz_config	\
-TQM866M_config		\
-TQM866M_66MHz_config	\
-TQM866M_80MHz_config	\
-TQM866M_100MHz_config	\
-TQM866M_133MHz_config:	unconfig
+TQM866M_config:		unconfig
 	@ >include/config.h
 	@[ -z "$(findstring _66MHz,$@)" ] || \
 		{ echo "#define CONFIG_66MHz"		>>include/config.h ; \
diff --git a/README b/README
index c223d4c..58267f1 100644
--- a/README
+++ b/README
@@ -3158,7 +3158,7 @@
 in Assembler); no C++ is used, so please do not use C++ style
 comments (//) in your code.
 
-Please also stick to the following formatiing rules:
+Please also stick to the following formatting rules:
 - remove any trailing white space
 - use TAB characters for indentation, not spaces
 - make sure NOT to use DOS '\r\n' line feeds
diff --git a/board/tqm8xx/tqm8xx.c b/board/tqm8xx/tqm8xx.c
index 73bee32..8cc86fc 100644
--- a/board/tqm8xx/tqm8xx.c
+++ b/board/tqm8xx/tqm8xx.c
@@ -128,6 +128,14 @@
 			break;
 		putc (*s);
 	}
+#if defined(CFG_866_CPUCLK_MIN) && defined(CFG_866_CPUCLK_MAX)
+	printf ("  [%d.%d...%d.%d MHz]",
+		CFG_866_CPUCLK_MIN / 1000000,
+		((CFG_866_CPUCLK_MIN % 1000000) + 50000) / 100000,
+		CFG_866_CPUCLK_MAX / 1000000,
+		((CFG_866_CPUCLK_MAX % 1000000) + 50000) / 100000
+	);
+#endif
 	putc ('\n');
 
 	return (0);
@@ -139,7 +147,7 @@
 {
 	volatile immap_t *immap = (immap_t *) CFG_IMMR;
 	volatile memctl8xx_t *memctl = &immap->im_memctl;
-	long int size8, size9;
+	long int size8, size9, size10;
 	long int size_b0 = 0;
 	long int size_b1 = 0;
 
@@ -228,9 +236,26 @@
 					   SDRAM_MAX_SIZE);
 	debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size9 >> 20);
 
-	if (size8 < size9) {		/* leave configuration at 9 columns */
+	udelay(1000);
+
+#if defined(CFG_MAMR_10COL)
+	/*
+	 * try 10 column mode
+	 */
+	size10 = dram_size (CFG_MAMR_10COL, (ulong *) SDRAM_BASE2_PRELIM,
+					     SDRAM_MAX_SIZE);
+	debug ("SDRAM Bank 0 in 10 column mode: %ld MB\n", size10 >> 20);
+#else
+	size10 = 0;
+#endif /* CFG_MAMR_10COL */
+
+	if ((size8 < size10) && (size9 < size10)) {
+		size_b0 = size10;
+	} else if ((size8 < size9) && (size10 < size9)) {
 		size_b0 = size9;
-	} else {					/* back to 8 columns            */
+		memctl->memc_mamr = CFG_MAMR_9COL;
+		udelay (500);
+	} else {
 		size_b0 = size8;
 		memctl->memc_mamr = CFG_MAMR_8COL;
 		udelay (500);
@@ -272,18 +297,15 @@
 	if (size_b1 > size_b0) {	/* SDRAM Bank 1 is bigger - map first   */
 
 		memctl->memc_or3 = ((-size_b1) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM;
-		memctl->memc_br3 =
-				(CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
+		memctl->memc_br3 = (CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
 
 		if (size_b0 > 0) {
 			/*
 			 * Position Bank 0 immediately above Bank 1
 			 */
-			memctl->memc_or2 =
-					((-size_b0) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM;
-			memctl->memc_br2 =
-					((CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V)
-					+ size_b1;
+			memctl->memc_or2 = ((-size_b0) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM;
+			memctl->memc_br2 = ((CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V)
+					   + size_b1;
 		} else {
 			unsigned long reg;
 
diff --git a/cpu/mpc8xx/Makefile b/cpu/mpc8xx/Makefile
index e8c93cc..de75fad 100644
--- a/cpu/mpc8xx/Makefile
+++ b/cpu/mpc8xx/Makefile
@@ -32,16 +32,17 @@
 	  fec.o i2c.o interrupts.o lcd.o scc.o		\
 	  serial.o speed.o spi.o \
 	  traps.o upatch.o video.o
+SOBJS	= plprcr_write.o
 
 all:	.depend $(START) $(LIB)
 
-$(LIB):	$(OBJS)
-	$(AR) crv $@ $(OBJS) kgdb.o
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS) kgdb.o
 
 #########################################################################
 
-.depend:	Makefile $(START:.o=.S) $(OBJS:.o=.c)
-		$(CC) -M $(CFLAGS) $(START:.o=.S) $(OBJS:.o=.c) > $@
+.depend:	Makefile $(START:.o=.S) $(OBJS:.o=.c) $(SOBJS:.o=.S)
+		$(CC) -M $(CFLAGS) $(START:.o=.S) $(OBJS:.o=.c) $(SOBJS:.o=.S) > $@
 
 sinclude .depend
 
diff --git a/cpu/mpc8xx/cpu_init.c b/cpu/mpc8xx/cpu_init.c
index cbf2126..c7716dd 100644
--- a/cpu/mpc8xx/cpu_init.c
+++ b/cpu/mpc8xx/cpu_init.c
@@ -42,7 +42,9 @@
 {
 #ifndef CONFIG_MBX
 	volatile memctl8xx_t *memctl = &immr->im_memctl;
+# ifdef CFG_PLPRCR
 	ulong mfmask;
+# endif
 #endif
 	ulong reg;
 
@@ -92,6 +94,7 @@
 	 *
 	 * For newer (starting MPC866) chips PLPRCR layout is different.
 	 */
+#ifdef CFG_PLPRCR
 	if (get_immr(0xFFFF) >= MPC8xx_NEW_CLK)
 	   mfmask = PLPRCR_MFACT_MSK;
 	else
@@ -105,6 +108,7 @@
 	   reg |= CFG_PLPRCR;			/* reset control bits   */
 	}
 	immr->im_clkrst.car_plprcr = reg;
+#endif
 
 	/*
 	 * Memory Controller:
diff --git a/cpu/mpc8xx/plprcr_write.S b/cpu/mpc8xx/plprcr_write.S
new file mode 100644
index 0000000..7d39a0e
--- /dev/null
+++ b/cpu/mpc8xx/plprcr_write.S
@@ -0,0 +1,145 @@
+/*
+ * (C) Copyright 2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <mpc8xx.h>
+#include <ppc_asm.tmpl>
+#include <asm/cache.h>
+
+#define CACHE_CMD_ENABLE	0x02000000
+#define CACHE_CMD_DISABLE	0x04000000
+#define CACHE_CMD_LOAD_LOCK	0x06000000
+#define CACHE_CMD_UNLOCK_LINE	0x08000000
+#define CACHE_CMD_UNLOCK_ALL	0x0A000000
+#define CACHE_CMD_INVALIDATE	0x0C000000
+#define SPEED_PLPRCR_WAIT_5CYC	150
+#define _CACHE_ALIGN_SIZE	16
+
+
+	.text
+	.align 2
+	.globl plprcr_write_866
+
+/*
+ * void plprcr_write_866 (long plprcr)
+ * Write PLPRCR, including workaround for device errata SIU4 and SIU9.
+ */
+
+plprcr_write_866:
+	mfspr	r10, LR		/* save the Link Register value */
+
+	/* turn instruction cache on (no MMU required for instructions)
+	 */
+	lis	r4, CACHE_CMD_ENABLE@h
+	ori	r4, r4, CACHE_CMD_ENABLE@l
+	mtspr	IC_CST, r4
+	isync
+
+	/* clear IC_CST error bits
+	 */
+	mfspr	r4, IC_CST
+
+	bl	plprcr_here
+
+plprcr_here:
+	mflr	r5
+
+	/* calculate relocation offset
+	 */
+	lis	r4, plprcr_here@h
+	ori	r4, r4, plprcr_here@l
+	sub	r5, r5, r4
+
+	/* calculate first address of this function
+	 */
+	lis	r6, plprcr_write_866@h
+	ori	r6, r6, plprcr_write_866@l
+	add	r6, r6, r5
+
+	/* calculate end address of this function
+	 */
+	lis	r7, plprcr_end@h
+	ori	r7, r7, plprcr_end@l
+	add	r7, r7, r5
+
+	/* load and lock code addresses
+	 */
+	mr	r5, r6
+
+plprcr_loop:
+	mtspr	IC_ADR, r5
+	addi	r5, r5, _CACHE_ALIGN_SIZE	/* increment by one line */
+
+	lis	r4, CACHE_CMD_LOAD_LOCK@h
+	ori	r4, r4, CACHE_CMD_LOAD_LOCK@l
+	mtspr	IC_CST, r4
+	isync
+
+	cmpw	r5, r7
+	blt	plprcr_loop
+
+	/* IC_CST error bits not evaluated
+	 */
+
+	/* switch PLPRCR
+	 */
+	mfspr	r4, IMMR		/* read IMMR */
+	rlwinm	r4, r4, 0, 0, 15	/* only high 16 bits count */
+
+	/* write sequence according to MPC866 Errata
+	 */
+	stw	r3, PLPRCR(r4)
+	isync
+
+	lis	r3, SPEED_PLPRCR_WAIT_5CYC@h
+	ori	r3, r3, SPEED_PLPRCR_WAIT_5CYC@l
+
+plprcr_wait:
+	cmpwi	r3, 0
+	beq	plprcr_wait_end
+	nop
+	subi	r3, r3, 1
+	b	plprcr_wait
+
+plprcr_wait_end:
+
+	/* turn instruction cache off
+	 */
+	lis	r4, CACHE_CMD_UNLOCK_ALL@h
+	ori	r4, r4, CACHE_CMD_UNLOCK_ALL@l
+	mtspr	IC_CST, r4
+	isync
+
+	lis	r4, CACHE_CMD_INVALIDATE@h
+	ori	r4, r4, CACHE_CMD_INVALIDATE@l
+	mtspr	IC_CST, r4
+	isync
+
+	lis	r4, CACHE_CMD_DISABLE@h
+	ori	r4, r4, CACHE_CMD_DISABLE@l
+	mtspr	IC_CST, r4
+	isync
+
+	mtspr	LR, r10		/* restore original Link Register value */
+	blr
+
+plprcr_end:
diff --git a/cpu/mpc8xx/speed.c b/cpu/mpc8xx/speed.c
index 3815537..8583eef 100644
--- a/cpu/mpc8xx/speed.c
+++ b/cpu/mpc8xx/speed.c
@@ -25,6 +25,8 @@
 #include <mpc8xx.h>
 #include <asm/processor.h>
 
+#ifndef CONFIG_TQM866M
+
 #define PITC_SHIFT 16
 #define PITR_SHIFT 16
 /* pitc values to time for 58/8192 seconds (about 70.8 milliseconds) */
@@ -203,4 +205,117 @@
 	return (0);
 }
 
+#else /* CONFIG_MPC866_et_al */
+
+static long init_pll_866 (long clk);
+
+/* This function sets up PLL (init_pll_866() is called) and
+ * fills gd->cpu_clk and gd->bus_clk according to the environment
+ * variable 'cpuclk' or to CFG_866_CPUCLK_DEFAULT (if 'cpuclk'
+ * contains invalid value).
+ * This functions requires an MPC866 series CPU.
+ */
+int get_clocks_866 (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	volatile immap_t *immr = (immap_t *) CFG_IMMR;
+	char              tmp[64];
+	long              cpuclk = 0;
+
+	if (getenv_r ("cpuclk", tmp, sizeof (tmp)) > 0)
+		cpuclk = simple_strtoul (tmp, NULL, 10) * 1000000;
+
+	if ((CFG_866_CPUCLK_MIN > cpuclk) || (CFG_866_CPUCLK_MAX < cpuclk))
+		cpuclk = CFG_866_CPUCLK_DEFAULT;
+
+	gd->cpu_clk = init_pll_866 (cpuclk);
+
+	if ((immr->im_clkrst.car_sccr & SCCR_EBDF11) == 0)
+		gd->bus_clk = gd->cpu_clk;
+	else
+		gd->bus_clk = gd->cpu_clk / 2;
+
+	return (0);
+}
+
+/* Adjust sdram refresh rate to actual CPU clock.
+ */
+int sdram_adjust_866 (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	volatile immap_t *immr = (immap_t *) CFG_IMMR;
+	long              mamr;
+
+	mamr = immr->im_memctl.memc_mamr;
+	mamr &= ~MAMR_PTA_MSK;
+	mamr |= ((gd->cpu_clk / CFG_866_PTA_PER_CLK) << MAMR_PTA_SHIFT);
+	immr->im_memctl.memc_mamr = mamr;
+
+	return (0);
+}
+
+/* Configure PLL for MPC866/859 CPU series
+ * PLL multiplication factor is set to the value nearest to the desired clk,
+ * assuming a oscclk of 10 MHz.
+ */
+static long init_pll_866 (long clk)
+{
+	extern void plprcr_write_866 (long);
+
+	volatile immap_t *immr = (immap_t *) CFG_IMMR;
+	long              n, plprcr;
+	char              mfi, mfn, mfd, s, pdf;
+	long              step_mfi, step_mfn;
+
+	pdf = 0;
+	if (clk < 80000000) {
+		s = 1;
+		step_mfi = CFG_866_OSCCLK / 2;
+		mfd = 14;
+		step_mfn = CFG_866_OSCCLK / 30;
+	} else {
+		s = 0;
+		step_mfi = CFG_866_OSCCLK;
+		mfd = 29;
+		step_mfn = CFG_866_OSCCLK / 30;
+	}
+
+	/* Calculate integer part of multiplication factor
+	 */
+	n = clk / step_mfi;
+	mfi = (char)n;
+
+	/* Calculate numerator of fractional part of multiplication factor
+	 */
+	n = clk - (n * step_mfi);
+	mfn = (char)(n / step_mfn);
+
+	/* Calculate effective clk
+	 */
+	n = (mfi * step_mfi) + (mfn * step_mfn);
+
+	immr->im_clkrstk.cark_plprcrk = KAPWR_KEY;
+
+	plprcr = (immr->im_clkrst.car_plprcr & ~(PLPRCR_MFN_MSK
+			| PLPRCR_MFD_MSK | PLPRCR_S_MSK
+			| PLPRCR_MFI_MSK | PLPRCR_DBRMO))
+			| (mfn << PLPRCR_MFN_SHIFT)
+			| (mfd << PLPRCR_MFD_SHIFT)
+			| (s << PLPRCR_S_SHIFT)
+			| (mfi << PLPRCR_MFI_SHIFT)
+			| (pdf << PLPRCR_PDF_SHIFT);
+
+	if( (mfn > 0) && ((mfd / mfn) > 10) )
+		plprcr |= PLPRCR_DBRMO;
+
+	plprcr_write_866 (plprcr);		/* set value using SIU4/9 workaround */
+	immr->im_clkrstk.cark_plprcrk = 0x00000000;
+
+	return (n);
+}
+
+#endif /* CONFIG_MPC866_et_al */
+
 /* ------------------------------------------------------------------------- */
diff --git a/include/common.h b/include/common.h
index 206f8cf..c04a9d3 100644
--- a/include/common.h
+++ b/include/common.h
@@ -355,6 +355,8 @@
 
 /* $(CPU)/speed.c */
 int	get_clocks (void);
+int	get_clocks_866 (void);
+int	sdram_adjust_866 (void);
 #if defined(CONFIG_8260)
 int	prt_8260_clks (void);
 #endif
diff --git a/include/configs/TQM866M.h b/include/configs/TQM866M.h
index 0219836..31f6d73 100644
--- a/include/configs/TQM866M.h
+++ b/include/configs/TQM866M.h
@@ -12,7 +12,7 @@
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
@@ -36,27 +36,32 @@
 #define CONFIG_MPC866		1	/* This is a MPC866 CPU		*/
 #define CONFIG_TQM866M		1	/* ...on a TQM8xxM module	*/
 
-#define	CFG_8XX_XIN	10000000 /* XXX XXX XXX */
+#define CFG_866_OSCCLK		10000000	/*  10 MHz - PLL input clock		*/
+#define CFG_866_CPUCLK_MIN	40000000	/*  40 MHz - CPU minimum clock		*/
+#define CFG_866_CPUCLK_MAX	133000000	/* 133 MHz - CPU maximum clock		*/
+#define CFG_866_CPUCLK_DEFAULT	100000000	/* 100 MHz - CPU default clock		*/
+						/* (it will be used if there is no	*/
+						/* 'cpuclk' variable with valid value)	*/
 
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
+#define CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
 #undef	CONFIG_8xx_CONS_SMC2
 #undef	CONFIG_8xx_CONS_NONE
 
 #define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
 
-#define	CONFIG_BOOTCOUNT_LIMIT
+#define CONFIG_BOOTCOUNT_LIMIT
 
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
 
 #define CONFIG_BOARD_TYPES	1	/* support board types		*/
 
-#define CONFIG_PREBOOT	"echo;"	\
+#define CONFIG_PREBOOT	"echo;" \
 	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
 	"echo"
 
 #undef	CONFIG_BOOTARGS
 
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
+#define CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=$(serverip):$(rootpath)\0"			\
@@ -81,13 +86,13 @@
 
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define	CONFIG_STATUS_LED	1	/* Status LED enabled		*/
+#define CONFIG_STATUS_LED	1	/* Status LED enabled		*/
 
 #undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/
 
 /* enable I2C and select the hardware/software driver */
 #undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define	CONFIG_SOFT_I2C         1	/* I2C bit-banged		*/
+#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
 
 #define CFG_I2C_SPEED		93000	/* 93 kHz is supposed to work	*/
 #define CFG_I2C_SLAVE		0xFE
@@ -104,14 +109,14 @@
 #define I2C_TRISTATE	(immr->im_cpm.cp_pbdir &= ~PB_SDA)
 #define I2C_READ	((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
 #define I2C_SDA(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
-			else    immr->im_cpm.cp_pbdat &= ~PB_SDA
+			else	immr->im_cpm.cp_pbdat &= ~PB_SDA
 #define I2C_SCL(bit)	if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
-			else    immr->im_cpm.cp_pbdat &= ~PB_SCL
+			else	immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY	udelay(2)	/* 1/4 I2C clock duration */
 #endif	/* CONFIG_SOFT_I2C */
 
 #define CFG_I2C_EEPROM_ADDR	0x50		/* EEPROM AT24C256	*/
-#define CFG_I2C_EEPROM_ADDR_LEN	2		/* two byte address	*/
+#define CFG_I2C_EEPROM_ADDR_LEN 2		/* two byte address	*/
 #define CFG_EEPROM_PAGE_WRITE_BITS	4
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
 
@@ -120,7 +125,7 @@
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
 
-#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
+#define CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/
 
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
 				CFG_CMD_ASKENV	| \
@@ -136,31 +141,31 @@
 /*
  * Miscellaneous configurable options
  */
-#define	CFG_LONGHELP			/* undef to save memory		*/
-#define	CFG_PROMPT		"=> "	/* Monitor Command Prompt	*/
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT		"=> "	/* Monitor Command Prompt	*/
 
 #if 0
-#define	CFG_HUSH_PARSER		1	/* use "hush" command parser	*/
+#define CFG_HUSH_PARSER		1	/* use "hush" command parser	*/
 #endif
 #ifdef	CFG_HUSH_PARSER
-#define	CFG_PROMPT_HUSH_PS2	"> "
+#define CFG_PROMPT_HUSH_PS2	"> "
 #endif
 
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE		1024	/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE		1024	/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE		256	/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE		256	/* Console I/O Buffer Size	*/
 #endif
-#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define	CFG_MAXARGS		16	/* max number of command args	*/
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#define	CFG_LOAD_ADDR		0x100000	/* default load address	*/
+#define CFG_LOAD_ADDR		0x100000	/* default load address */
 
-#define	CFG_HZ			1000	/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
 
 #define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
@@ -178,28 +183,28 @@
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CFG_INIT_RAM_ADDR	CFG_IMMR
-#define	CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
-#define	CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
+#define CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
+#define CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define	CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
-#define	CFG_SDRAM_BASE		0x00000000
+#define CFG_SDRAM_BASE		0x00000000
 #define CFG_FLASH_BASE		0x40000000
-#define	CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
 #define CFG_MONITOR_BASE	CFG_FLASH_BASE
-#define	CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*-----------------------------------------------------------------------
  * FLASH organization
@@ -210,10 +215,10 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define	CFG_ENV_IS_IN_FLASH	1
-#define	CFG_ENV_OFFSET		0x40000	/*   Offset   of Environment Sector	*/
-#define	CFG_ENV_SIZE		0x08000	/* Total Size of Environment Sector	*/
-#define	CFG_ENV_SECT_SIZE	0x20000	/* Total Size of Environment Sector	*/
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_OFFSET		0x40000 /*   Offset   of Environment Sector	*/
+#define CFG_ENV_SIZE		0x08000 /* Total Size of Environment Sector	*/
+#define CFG_ENV_SECT_SIZE	0x20000 /* Total Size of Environment Sector	*/
 
 /* Address and size of Redundant Environment Sector	*/
 #define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
@@ -223,7 +228,7 @@
  * Hardware Information Block
  */
 #define CFG_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-#define CFG_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
+#define CFG_HWINFO_SIZE		0x00000040	/* size	  of HW Info block */
 #define CFG_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
 
 /*-----------------------------------------------------------------------
@@ -252,7 +257,7 @@
  *-----------------------------------------------------------------------
  * PCMCIA config., multi-function pin tri-state
  */
-#ifndef	CONFIG_CAN_DRIVER
+#ifndef CONFIG_CAN_DRIVER
 #define CFG_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
 #else	/* we must activate GPL5 in the SIUMCR for CAN */
 #define CFG_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
@@ -279,51 +284,15 @@
 #define CFG_PISCR	(PISCR_PS | PISCR_PITF)
 
 /*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit
- *
- * set PLL multiplication factor
- */
-#if defined(CONFIG_133MHz)
-    /* for 133 MHz, we use a 10 MHz clock:
-     * MFN = 0x09, MFD = 0x1D, S = 0, MFI = 13
-     */
-#define CFG_PLPRCR							\
-		( 9 << PLPRCR_MFN_SHIFT | 0x1D << PLPRCR_MFD_SHIFT  |	\
-		  0 << PLPRCR_S_SHIFT	| 0x0D << PLPRCR_MFI_SHIFT  |	\
-		  PLPRCR_TEXPS )
-#elif defined(CONFIG_80MHz) /* for  80 MHz, we use a 16 MHz clock *  5 */
-#define CFG_PLPRCR							\
-		( (5-1)<<PLPRCR_MFI_SHIFT | PLPRCR_TEXPS )
-#else			/* up to 66 MHz we use a 1:1 clock */
-#define CFG_PLPRCR	( PLPRCR_SPLSS | PLPRCR_TEXPS )
-#endif	/* CONFIG_??MHz */
-
-/*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
  *-----------------------------------------------------------------------
  * Set clock output, timebase and RTC source and divider,
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
-#if defined(CONFIG_133MHz)  /* for 133 MHz, we use a 10 MHz clock * 13 */
-#define CFG_SCCR	(/* SCCR_TBS  | */ \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#elif defined(CONFIG_80MHz) /* for  80 MHz, we use a 16 MHz clock *  5 */
-#define CFG_SCCR	(/* SCCR_TBS  | */ \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
-			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
-			 SCCR_DFALCD00)
-#else			/* up to 66 MHz we use a 1:1 clock */
-#define CFG_SCCR	(SCCR_TBS     | \
-			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
+#define CFG_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)
-#endif	/* CONFIG_??MHz */
 
 /*-----------------------------------------------------------------------
  * PCMCIA stuff
@@ -344,10 +313,10 @@
  *-----------------------------------------------------------------------
  */
 
-#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
+#define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
 
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
-#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
+#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
+#undef	CONFIG_IDE_LED			/* LED	 for ide not supported	*/
 #undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
 
 #define CFG_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
@@ -371,7 +340,7 @@
  *-----------------------------------------------------------------------
  *
  */
-#define CFG_DER	0
+#define CFG_DER 0
 
 /*
  * Init Memory Controller:
@@ -390,27 +359,10 @@
 #define CFG_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
 
 /*
- * FLASH timing:
+ * FLASH timing: Default value of OR0 after reset
  */
-#if defined(CONFIG_133MHz)
-/* 133 MHz CPU - 66 MHz bus: */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_100MHz)
-/* 100 MHz CPU - 50 MHz bus: */
-#elif defined(CONFIG_80MHz)
-/* 80 MHz CPU - 40 MHz bus: ACS = 00, TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | 0       | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#elif defined(CONFIG_66MHz)
-/* 66 MHz CPU - 66 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_3_CLK | OR_EHTR | OR_BI)
-#else		/*   50 MHz */
-/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
-				 OR_SCY_2_CLK | OR_EHTR | OR_BI)
-#endif	/*CONFIG_??MHz */
+#define CFG_OR_TIMING_FLASH	(OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
+				 OR_SCY_15_CLK | OR_TRLX)
 
 #define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
 #define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
@@ -426,7 +378,7 @@
  */
 #define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
 #define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
-#define	SDRAM_MAX_SIZE		(256 << 20)	/* max 256 MB per bank	*/
+#define SDRAM_MAX_SIZE		(256 << 20)	/* max 256 MB per bank	*/
 
 /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
 #define CFG_OR_TIMING_SDRAM	0x00000A00
@@ -434,11 +386,11 @@
 #define CFG_OR2_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
 #define CFG_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
 
-#ifndef	CONFIG_CAN_DRIVER
-#define	CFG_OR3_PRELIM	CFG_OR2_PRELIM
+#ifndef CONFIG_CAN_DRIVER
+#define CFG_OR3_PRELIM	CFG_OR2_PRELIM
 #define CFG_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
 #else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
-#define	CFG_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
+#define CFG_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
 #define CFG_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
 #define CFG_OR3_CAN		(CFG_CAN_OR_AM | OR_G5LA | OR_BI)
 #define CFG_BR3_CAN		((CFG_CAN_BASE & BR_BA_MSK) | \
@@ -446,42 +398,21 @@
 #endif	/* CONFIG_CAN_DRIVER */
 
 /*
+ * 
+ * 4096	Rows from SDRAM example configuration
+ * 1000	factor s -> ms
+ * 64	PTP (pre-divider from MPTPR) from SDRAM example configuration
+ * 4	Number of refresh cycles per period
+ * 64	Refresh cycle in ms per number of rows
+ */
+#define CFG_866_PTA_PER_CLK	((4096 * 64 * 1000) / (4 * 64))
+
+/*
  * Memory Periodic Timer Prescaler
- *
- * The Divider for PTA (refresh timer) configuration is based on an
- * example SDRAM configuration (64 MBit, one bank). The adjustment to
- * the number of chip selects (NCS) and the actually needed refresh
- * rate is done by setting MPTPR.
- *
- * PTA is calculated from
- *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
- *
- *	gclk	  CPU clock (not bus clock!)
- *	Trefresh  Refresh cycle * 4 (four word bursts used)
- *
- * 4096  Rows from SDRAM example configuration
- * 1000  factor s -> ms
- *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
- *    4  Number of refresh cycles per period
- *   64  Refresh cycle in ms per number of rows
- * --------------------------------------------
- * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
- *
- * 50 MHz => 50.000.000 / Divider =  98
- * 66 Mhz => 66.000.000 / Divider = 129
- * 80 Mhz => 80.000.000 / Divider = 156
+ * Periodic timer for refresh, start with refresh rate for 40 MHz clock
+ * (CFG_866_CPUCLK_MIN / CFG_866_PTA_PER_CLK)
  */
-#if   defined(CONFIG_133MHz)
-#define CFG_MAMR_PTA		129
-#elif defined(CONFIG_100MHz)
-#define CFG_MAMR_PTA		 98
-#elif defined(CONFIG_80MHz)
-#define CFG_MAMR_PTA		156
-#elif defined(CONFIG_66MHz)
-#define CFG_MAMR_PTA		129
-#else		/*   50 MHz */
-#define CFG_MAMR_PTA		 98
-#endif	/*CONFIG_??MHz */
+#define CFG_MAMR_PTA		39
 
 /*
  * For 16 MBit, refresh rates could be 31.3 us
@@ -510,13 +441,17 @@
 #define CFG_MAMR_9COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
 			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
 			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
+/* 10 column SDRAM */
+#define CFG_MAMR_10COL	((CFG_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
+			 MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9  |	\
+			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
 
 /*
  * Internal Definitions
  *
  * Boot Flags
  */
-#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/
 
 #define CONFIG_SCC1_ENET
diff --git a/lib_ppc/board.c b/lib_ppc/board.c
index c495d49..5b0dd4d 100644
--- a/lib_ppc/board.c
+++ b/lib_ppc/board.c
@@ -260,8 +260,11 @@
 #if defined(CONFIG_BOARD_EARLY_INIT_F)
 	board_early_init_f,
 #endif
+
+#if !defined(CONFIG_TQM866M)
 	get_clocks,		/* get CPU and bus clocks (etc.) */
 	init_timebase,
+#endif
 #ifdef CFG_ALLOC_DPRAM
 #if !(defined(CONFIG_8260) || defined(CONFIG_MPC8560))
 	dpram_init,
@@ -271,6 +274,11 @@
 	board_postclk_init,
 #endif
 	env_init,
+#if defined(CONFIG_TQM866M)
+	get_clocks_866,		/* get CPU and bus clocks according to the environment variable */
+	sdram_adjust_866,	/* adjust sdram refresh rate according to the new clock */
+	init_timebase,
+#endif
 	init_baudrate,
 	serial_init,
 	console_init_f,
@@ -741,7 +749,7 @@
 #endif
 
 #if defined(CFG_GT_6426x) || defined(CONFIG_PN62) || defined(CONFIG_PPCHAMELEONEVB) || \
-     defined(CONFIG_MPC8540ADS) || defined(CONFIG_MPC8560ADS)
+    defined(CONFIG_MPC8540ADS) || defined(CONFIG_MPC8560ADS)
 	/* handle the 2nd ethernet address */
 
 	s = getenv ("eth1addr");