| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (C) 2018 Texas Instruments Incorporated - https://www.ti.com/ |
| * |
| * Texas Instruments' K3 SD Host Controller Interface |
| */ |
| |
| #include <clk.h> |
| #include <common.h> |
| #include <dm.h> |
| #include <malloc.h> |
| #include <mmc.h> |
| #include <power-domain.h> |
| #include <regmap.h> |
| #include <sdhci.h> |
| #include <soc.h> |
| #include <dm/device_compat.h> |
| #include <linux/bitops.h> |
| #include <linux/err.h> |
| |
| /* CTL_CFG Registers */ |
| #define CTL_CFG_2 0x14 |
| |
| #define SLOTTYPE_MASK GENMASK(31, 30) |
| #define SLOTTYPE_EMBEDDED BIT(30) |
| |
| /* PHY Registers */ |
| #define PHY_CTRL1 0x100 |
| #define PHY_CTRL2 0x104 |
| #define PHY_CTRL3 0x108 |
| #define PHY_CTRL4 0x10C |
| #define PHY_CTRL5 0x110 |
| #define PHY_CTRL6 0x114 |
| #define PHY_STAT1 0x130 |
| #define PHY_STAT2 0x134 |
| |
| #define IOMUX_ENABLE_SHIFT 31 |
| #define IOMUX_ENABLE_MASK BIT(IOMUX_ENABLE_SHIFT) |
| #define OTAPDLYENA_SHIFT 20 |
| #define OTAPDLYENA_MASK BIT(OTAPDLYENA_SHIFT) |
| #define OTAPDLYSEL_SHIFT 12 |
| #define OTAPDLYSEL_MASK GENMASK(15, 12) |
| #define STRBSEL_SHIFT 24 |
| #define STRBSEL_4BIT_MASK GENMASK(27, 24) |
| #define STRBSEL_8BIT_MASK GENMASK(31, 24) |
| #define SEL50_SHIFT 8 |
| #define SEL50_MASK BIT(SEL50_SHIFT) |
| #define SEL100_SHIFT 9 |
| #define SEL100_MASK BIT(SEL100_SHIFT) |
| #define FREQSEL_SHIFT 8 |
| #define FREQSEL_MASK GENMASK(10, 8) |
| #define CLKBUFSEL_SHIFT 0 |
| #define CLKBUFSEL_MASK GENMASK(2, 0) |
| #define DLL_TRIM_ICP_SHIFT 4 |
| #define DLL_TRIM_ICP_MASK GENMASK(7, 4) |
| #define DR_TY_SHIFT 20 |
| #define DR_TY_MASK GENMASK(22, 20) |
| #define ENDLL_SHIFT 1 |
| #define ENDLL_MASK BIT(ENDLL_SHIFT) |
| #define DLLRDY_SHIFT 0 |
| #define DLLRDY_MASK BIT(DLLRDY_SHIFT) |
| #define PDB_SHIFT 0 |
| #define PDB_MASK BIT(PDB_SHIFT) |
| #define CALDONE_SHIFT 1 |
| #define CALDONE_MASK BIT(CALDONE_SHIFT) |
| #define RETRIM_SHIFT 17 |
| #define RETRIM_MASK BIT(RETRIM_SHIFT) |
| #define SELDLYTXCLK_SHIFT 17 |
| #define SELDLYTXCLK_MASK BIT(SELDLYTXCLK_SHIFT) |
| #define SELDLYRXCLK_SHIFT 16 |
| #define SELDLYRXCLK_MASK BIT(SELDLYRXCLK_SHIFT) |
| #define ITAPDLYSEL_SHIFT 0 |
| #define ITAPDLYSEL_MASK GENMASK(4, 0) |
| #define ITAPDLYENA_SHIFT 8 |
| #define ITAPDLYENA_MASK BIT(ITAPDLYENA_SHIFT) |
| #define ITAPCHGWIN_SHIFT 9 |
| #define ITAPCHGWIN_MASK BIT(ITAPCHGWIN_SHIFT) |
| |
| #define DRIVER_STRENGTH_50_OHM 0x0 |
| #define DRIVER_STRENGTH_33_OHM 0x1 |
| #define DRIVER_STRENGTH_66_OHM 0x2 |
| #define DRIVER_STRENGTH_100_OHM 0x3 |
| #define DRIVER_STRENGTH_40_OHM 0x4 |
| |
| #define AM654_SDHCI_MIN_FREQ 400000 |
| #define CLOCK_TOO_SLOW_HZ 50000000 |
| |
| struct am654_sdhci_plat { |
| struct mmc_config cfg; |
| struct mmc mmc; |
| struct regmap *base; |
| bool non_removable; |
| u32 otap_del_sel[MMC_MODES_END]; |
| u32 itap_del_sel[MMC_MODES_END]; |
| u32 trm_icp; |
| u32 drv_strength; |
| u32 strb_sel; |
| u32 clkbuf_sel; |
| u32 flags; |
| #define DLL_PRESENT BIT(0) |
| #define IOMUX_PRESENT BIT(1) |
| #define FREQSEL_2_BIT BIT(2) |
| #define STRBSEL_4_BIT BIT(3) |
| #define DLL_CALIB BIT(4) |
| }; |
| |
| struct timing_data { |
| const char *otap_binding; |
| const char *itap_binding; |
| u32 capability; |
| }; |
| |
| static const struct timing_data td[] = { |
| [MMC_LEGACY] = {"ti,otap-del-sel-legacy", |
| "ti,itap-del-sel-legacy", |
| 0}, |
| [MMC_HS] = {"ti,otap-del-sel-mmc-hs", |
| "ti,itap-del-sel-mms-hs", |
| MMC_CAP(MMC_HS)}, |
| [SD_HS] = {"ti,otap-del-sel-sd-hs", |
| "ti,itap-del-sel-sd-hs", |
| MMC_CAP(SD_HS)}, |
| [UHS_SDR12] = {"ti,otap-del-sel-sdr12", |
| "ti,itap-del-sel-sdr12", |
| MMC_CAP(UHS_SDR12)}, |
| [UHS_SDR25] = {"ti,otap-del-sel-sdr25", |
| "ti,itap-del-sel-sdr25", |
| MMC_CAP(UHS_SDR25)}, |
| [UHS_SDR50] = {"ti,otap-del-sel-sdr50", |
| NULL, |
| MMC_CAP(UHS_SDR50)}, |
| [UHS_SDR104] = {"ti,otap-del-sel-sdr104", |
| NULL, |
| MMC_CAP(UHS_SDR104)}, |
| [UHS_DDR50] = {"ti,otap-del-sel-ddr50", |
| NULL, |
| MMC_CAP(UHS_DDR50)}, |
| [MMC_DDR_52] = {"ti,otap-del-sel-ddr52", |
| "ti,itap-del-sel-ddr52", |
| MMC_CAP(MMC_DDR_52)}, |
| [MMC_HS_200] = {"ti,otap-del-sel-hs200", |
| NULL, |
| MMC_CAP(MMC_HS_200)}, |
| [MMC_HS_400] = {"ti,otap-del-sel-hs400", |
| NULL, |
| MMC_CAP(MMC_HS_400)}, |
| }; |
| |
| struct am654_driver_data { |
| const struct sdhci_ops *ops; |
| u32 flags; |
| }; |
| |
| static int am654_sdhci_setup_dll(struct am654_sdhci_plat *plat, |
| unsigned int speed) |
| { |
| int sel50, sel100, freqsel; |
| u32 mask, val; |
| int ret; |
| |
| /* Disable delay chain mode */ |
| regmap_update_bits(plat->base, PHY_CTRL5, |
| SELDLYTXCLK_MASK | SELDLYRXCLK_MASK, 0); |
| |
| if (plat->flags & FREQSEL_2_BIT) { |
| switch (speed) { |
| case 200000000: |
| sel50 = 0; |
| sel100 = 0; |
| break; |
| case 100000000: |
| sel50 = 0; |
| sel100 = 1; |
| break; |
| default: |
| sel50 = 1; |
| sel100 = 0; |
| } |
| |
| /* Configure PHY DLL frequency */ |
| mask = SEL50_MASK | SEL100_MASK; |
| val = (sel50 << SEL50_SHIFT) | (sel100 << SEL100_SHIFT); |
| regmap_update_bits(plat->base, PHY_CTRL5, mask, val); |
| } else { |
| switch (speed) { |
| case 200000000: |
| freqsel = 0x0; |
| break; |
| default: |
| freqsel = 0x4; |
| } |
| regmap_update_bits(plat->base, PHY_CTRL5, FREQSEL_MASK, |
| freqsel << FREQSEL_SHIFT); |
| } |
| |
| /* Configure DLL TRIM */ |
| mask = DLL_TRIM_ICP_MASK; |
| val = plat->trm_icp << DLL_TRIM_ICP_SHIFT; |
| |
| /* Configure DLL driver strength */ |
| mask |= DR_TY_MASK; |
| val |= plat->drv_strength << DR_TY_SHIFT; |
| regmap_update_bits(plat->base, PHY_CTRL1, mask, val); |
| |
| /* Enable DLL */ |
| regmap_update_bits(plat->base, PHY_CTRL1, ENDLL_MASK, |
| 0x1 << ENDLL_SHIFT); |
| /* |
| * Poll for DLL ready. Use a one second timeout. |
| * Works in all experiments done so far |
| */ |
| ret = regmap_read_poll_timeout(plat->base, PHY_STAT1, val, |
| val & DLLRDY_MASK, 1000, 1000000); |
| |
| return ret; |
| } |
| |
| static void am654_sdhci_write_itapdly(struct am654_sdhci_plat *plat, |
| u32 itapdly) |
| { |
| /* Set ITAPCHGWIN before writing to ITAPDLY */ |
| regmap_update_bits(plat->base, PHY_CTRL4, ITAPCHGWIN_MASK, |
| 1 << ITAPCHGWIN_SHIFT); |
| regmap_update_bits(plat->base, PHY_CTRL4, ITAPDLYSEL_MASK, |
| itapdly << ITAPDLYSEL_SHIFT); |
| regmap_update_bits(plat->base, PHY_CTRL4, ITAPCHGWIN_MASK, 0); |
| } |
| |
| static void am654_sdhci_setup_delay_chain(struct am654_sdhci_plat *plat, |
| int mode) |
| { |
| u32 mask, val; |
| |
| val = 1 << SELDLYTXCLK_SHIFT | 1 << SELDLYRXCLK_SHIFT; |
| mask = SELDLYTXCLK_MASK | SELDLYRXCLK_MASK; |
| regmap_update_bits(plat->base, PHY_CTRL5, mask, val); |
| |
| am654_sdhci_write_itapdly(plat, plat->itap_del_sel[mode]); |
| } |
| |
| static int am654_sdhci_set_ios_post(struct sdhci_host *host) |
| { |
| struct udevice *dev = host->mmc->dev; |
| struct am654_sdhci_plat *plat = dev_get_plat(dev); |
| unsigned int speed = host->mmc->clock; |
| int mode = host->mmc->selected_mode; |
| u32 otap_del_sel; |
| u32 mask, val; |
| int ret; |
| |
| /* Reset SD Clock Enable */ |
| val = sdhci_readw(host, SDHCI_CLOCK_CONTROL); |
| val &= ~SDHCI_CLOCK_CARD_EN; |
| sdhci_writew(host, val, SDHCI_CLOCK_CONTROL); |
| |
| regmap_update_bits(plat->base, PHY_CTRL1, ENDLL_MASK, 0); |
| |
| /* restart clock */ |
| sdhci_set_clock(host->mmc, speed); |
| |
| /* switch phy back on */ |
| otap_del_sel = plat->otap_del_sel[mode]; |
| mask = OTAPDLYENA_MASK | OTAPDLYSEL_MASK; |
| val = (1 << OTAPDLYENA_SHIFT) | |
| (otap_del_sel << OTAPDLYSEL_SHIFT); |
| |
| /* Write to STRBSEL for HS400 speed mode */ |
| if (host->mmc->selected_mode == MMC_HS_400) { |
| if (plat->flags & STRBSEL_4_BIT) |
| mask |= STRBSEL_4BIT_MASK; |
| else |
| mask |= STRBSEL_8BIT_MASK; |
| |
| val |= plat->strb_sel << STRBSEL_SHIFT; |
| } |
| |
| regmap_update_bits(plat->base, PHY_CTRL4, mask, val); |
| |
| if (mode > UHS_SDR25 && speed >= CLOCK_TOO_SLOW_HZ) { |
| ret = am654_sdhci_setup_dll(plat, speed); |
| if (ret) |
| return ret; |
| } else { |
| am654_sdhci_setup_delay_chain(plat, mode); |
| } |
| |
| regmap_update_bits(plat->base, PHY_CTRL5, CLKBUFSEL_MASK, |
| plat->clkbuf_sel); |
| |
| return 0; |
| } |
| |
| int am654_sdhci_init(struct am654_sdhci_plat *plat) |
| { |
| u32 ctl_cfg_2 = 0; |
| u32 mask, val; |
| int ret; |
| |
| /* Reset OTAP to default value */ |
| mask = OTAPDLYENA_MASK | OTAPDLYSEL_MASK; |
| regmap_update_bits(plat->base, PHY_CTRL4, mask, 0x0); |
| |
| if (plat->flags & DLL_CALIB) { |
| regmap_read(plat->base, PHY_STAT1, &val); |
| if (~val & CALDONE_MASK) { |
| /* Calibrate IO lines */ |
| regmap_update_bits(plat->base, PHY_CTRL1, PDB_MASK, |
| PDB_MASK); |
| ret = regmap_read_poll_timeout(plat->base, PHY_STAT1, |
| val, val & CALDONE_MASK, |
| 1, 20); |
| if (ret) |
| return ret; |
| } |
| } |
| |
| /* Enable pins by setting IO mux to 0 */ |
| if (plat->flags & IOMUX_PRESENT) |
| regmap_update_bits(plat->base, PHY_CTRL1, IOMUX_ENABLE_MASK, 0); |
| |
| /* Set slot type based on SD or eMMC */ |
| if (plat->non_removable) |
| ctl_cfg_2 = SLOTTYPE_EMBEDDED; |
| |
| regmap_update_bits(plat->base, CTL_CFG_2, SLOTTYPE_MASK, ctl_cfg_2); |
| |
| return 0; |
| } |
| |
| #define MAX_SDCD_DEBOUNCE_TIME 2000 |
| static int am654_sdhci_deferred_probe(struct sdhci_host *host) |
| { |
| struct udevice *dev = host->mmc->dev; |
| struct am654_sdhci_plat *plat = dev_get_plat(dev); |
| unsigned long start; |
| int val; |
| |
| /* |
| * The controller takes about 1 second to debounce the card detect line |
| * and doesn't let us power on until that time is up. Instead of waiting |
| * for 1 second at every stage, poll on the CARD_PRESENT bit upto a |
| * maximum of 2 seconds to be safe.. |
| */ |
| start = get_timer(0); |
| do { |
| if (get_timer(start) > MAX_SDCD_DEBOUNCE_TIME) |
| return -ENOMEDIUM; |
| |
| val = mmc_getcd(host->mmc); |
| } while (!val); |
| |
| am654_sdhci_init(plat); |
| |
| return sdhci_probe(dev); |
| } |
| |
| static void am654_sdhci_write_b(struct sdhci_host *host, u8 val, int reg) |
| { |
| if (reg == SDHCI_HOST_CONTROL) { |
| switch (host->mmc->selected_mode) { |
| /* |
| * According to the data manual, HISPD bit |
| * should not be set in these speed modes. |
| */ |
| case SD_HS: |
| case MMC_HS: |
| case UHS_SDR12: |
| case UHS_SDR25: |
| val &= ~SDHCI_CTRL_HISPD; |
| default: |
| break; |
| } |
| } |
| |
| writeb(val, host->ioaddr + reg); |
| } |
| #ifdef MMC_SUPPORTS_TUNING |
| #define ITAP_MAX 32 |
| static int am654_sdhci_execute_tuning(struct mmc *mmc, u8 opcode) |
| { |
| struct udevice *dev = mmc->dev; |
| struct am654_sdhci_plat *plat = dev_get_plat(dev); |
| int cur_val, prev_val = 1, fail_len = 0, pass_window = 0, pass_len; |
| u32 itap; |
| |
| /* Enable ITAPDLY */ |
| regmap_update_bits(plat->base, PHY_CTRL4, ITAPDLYENA_MASK, |
| 1 << ITAPDLYENA_SHIFT); |
| |
| for (itap = 0; itap < ITAP_MAX; itap++) { |
| am654_sdhci_write_itapdly(plat, itap); |
| |
| cur_val = !mmc_send_tuning(mmc, opcode); |
| if (cur_val && !prev_val) |
| pass_window = itap; |
| |
| if (!cur_val) |
| fail_len++; |
| |
| prev_val = cur_val; |
| } |
| /* |
| * Having determined the length of the failing window and start of |
| * the passing window calculate the length of the passing window and |
| * set the final value halfway through it considering the range as a |
| * circular buffer |
| */ |
| pass_len = ITAP_MAX - fail_len; |
| itap = (pass_window + (pass_len >> 1)) % ITAP_MAX; |
| am654_sdhci_write_itapdly(plat, itap); |
| |
| return 0; |
| } |
| #endif |
| const struct sdhci_ops am654_sdhci_ops = { |
| #ifdef MMC_SUPPORTS_TUNING |
| .platform_execute_tuning = am654_sdhci_execute_tuning, |
| #endif |
| .deferred_probe = am654_sdhci_deferred_probe, |
| .set_ios_post = &am654_sdhci_set_ios_post, |
| .set_control_reg = sdhci_set_control_reg, |
| .write_b = am654_sdhci_write_b, |
| }; |
| |
| const struct am654_driver_data am654_drv_data = { |
| .ops = &am654_sdhci_ops, |
| .flags = DLL_PRESENT | IOMUX_PRESENT | FREQSEL_2_BIT | STRBSEL_4_BIT, |
| }; |
| |
| const struct am654_driver_data am654_sr1_drv_data = { |
| .ops = &am654_sdhci_ops, |
| .flags = IOMUX_PRESENT | FREQSEL_2_BIT | DLL_PRESENT | DLL_CALIB | |
| STRBSEL_4_BIT, |
| }; |
| |
| const struct am654_driver_data j721e_8bit_drv_data = { |
| .ops = &am654_sdhci_ops, |
| .flags = DLL_PRESENT | DLL_CALIB, |
| }; |
| |
| static int j721e_4bit_sdhci_set_ios_post(struct sdhci_host *host) |
| { |
| struct udevice *dev = host->mmc->dev; |
| struct am654_sdhci_plat *plat = dev_get_plat(dev); |
| u32 otap_del_sel, mask, val; |
| |
| otap_del_sel = plat->otap_del_sel[host->mmc->selected_mode]; |
| mask = OTAPDLYENA_MASK | OTAPDLYSEL_MASK; |
| val = (1 << OTAPDLYENA_SHIFT) | (otap_del_sel << OTAPDLYSEL_SHIFT); |
| regmap_update_bits(plat->base, PHY_CTRL4, mask, val); |
| |
| regmap_update_bits(plat->base, PHY_CTRL5, CLKBUFSEL_MASK, |
| plat->clkbuf_sel); |
| |
| return 0; |
| } |
| |
| const struct sdhci_ops j721e_4bit_sdhci_ops = { |
| #ifdef MMC_SUPPORTS_TUNING |
| .platform_execute_tuning = am654_sdhci_execute_tuning, |
| #endif |
| .deferred_probe = am654_sdhci_deferred_probe, |
| .set_ios_post = &j721e_4bit_sdhci_set_ios_post, |
| .set_control_reg = sdhci_set_control_reg, |
| .write_b = am654_sdhci_write_b, |
| }; |
| |
| const struct am654_driver_data j721e_4bit_drv_data = { |
| .ops = &j721e_4bit_sdhci_ops, |
| .flags = IOMUX_PRESENT, |
| }; |
| |
| static const struct am654_driver_data sdhci_am64_8bit_drvdata = { |
| .ops = &am654_sdhci_ops, |
| .flags = DLL_PRESENT | DLL_CALIB, |
| }; |
| |
| static const struct am654_driver_data sdhci_am64_4bit_drvdata = { |
| .ops = &j721e_4bit_sdhci_ops, |
| .flags = IOMUX_PRESENT, |
| }; |
| |
| const struct soc_attr am654_sdhci_soc_attr[] = { |
| { .family = "AM65X", .revision = "SR1.0", .data = &am654_sr1_drv_data}, |
| {/* sentinel */} |
| }; |
| |
| static int sdhci_am654_get_otap_delay(struct udevice *dev, |
| struct mmc_config *cfg) |
| { |
| struct am654_sdhci_plat *plat = dev_get_plat(dev); |
| int ret; |
| int i; |
| |
| /* ti,otap-del-sel-legacy is mandatory */ |
| ret = dev_read_u32(dev, "ti,otap-del-sel-legacy", |
| &plat->otap_del_sel[0]); |
| if (ret) |
| return ret; |
| /* |
| * Remove the corresponding capability if an otap-del-sel |
| * value is not found |
| */ |
| for (i = MMC_HS; i <= MMC_HS_400; i++) { |
| ret = dev_read_u32(dev, td[i].otap_binding, |
| &plat->otap_del_sel[i]); |
| if (ret) { |
| dev_dbg(dev, "Couldn't find %s\n", td[i].otap_binding); |
| /* |
| * Remove the corresponding capability |
| * if an otap-del-sel value is not found |
| */ |
| cfg->host_caps &= ~td[i].capability; |
| } |
| |
| if (td[i].itap_binding) |
| dev_read_u32(dev, td[i].itap_binding, |
| &plat->itap_del_sel[i]); |
| } |
| |
| return 0; |
| } |
| |
| static int am654_sdhci_probe(struct udevice *dev) |
| { |
| struct am654_driver_data *drv_data = |
| (struct am654_driver_data *)dev_get_driver_data(dev); |
| struct am654_sdhci_plat *plat = dev_get_plat(dev); |
| struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev); |
| struct sdhci_host *host = dev_get_priv(dev); |
| struct mmc_config *cfg = &plat->cfg; |
| const struct soc_attr *soc; |
| const struct am654_driver_data *soc_drv_data; |
| struct clk clk; |
| unsigned long clock; |
| int ret; |
| |
| ret = clk_get_by_name(dev, "clk_xin", &clk); |
| if (ret) { |
| dev_err(dev, "failed to get clock\n"); |
| return ret; |
| } |
| |
| clock = clk_get_rate(&clk); |
| if (IS_ERR_VALUE(clock)) { |
| dev_err(dev, "failed to get rate\n"); |
| return clock; |
| } |
| |
| host->max_clk = clock; |
| host->mmc = &plat->mmc; |
| host->mmc->dev = dev; |
| host->ops = drv_data->ops; |
| ret = sdhci_setup_cfg(cfg, host, cfg->f_max, |
| AM654_SDHCI_MIN_FREQ); |
| if (ret) |
| return ret; |
| |
| ret = sdhci_am654_get_otap_delay(dev, cfg); |
| if (ret) |
| return ret; |
| |
| /* Update ops based on SoC revision */ |
| soc = soc_device_match(am654_sdhci_soc_attr); |
| if (soc && soc->data) { |
| soc_drv_data = soc->data; |
| host->ops = soc_drv_data->ops; |
| } |
| |
| host->mmc->priv = host; |
| upriv->mmc = host->mmc; |
| |
| regmap_init_mem_index(dev_ofnode(dev), &plat->base, 1); |
| |
| return 0; |
| } |
| |
| static int am654_sdhci_of_to_plat(struct udevice *dev) |
| { |
| struct am654_sdhci_plat *plat = dev_get_plat(dev); |
| struct sdhci_host *host = dev_get_priv(dev); |
| struct mmc_config *cfg = &plat->cfg; |
| u32 drv_strength; |
| int ret; |
| |
| host->name = dev->name; |
| host->ioaddr = dev_read_addr_ptr(dev); |
| plat->non_removable = dev_read_bool(dev, "non-removable"); |
| |
| if (plat->flags & DLL_PRESENT) { |
| ret = dev_read_u32(dev, "ti,trm-icp", &plat->trm_icp); |
| if (ret) |
| return ret; |
| |
| ret = dev_read_u32(dev, "ti,driver-strength-ohm", |
| &drv_strength); |
| if (ret) |
| return ret; |
| |
| switch (drv_strength) { |
| case 50: |
| plat->drv_strength = DRIVER_STRENGTH_50_OHM; |
| break; |
| case 33: |
| plat->drv_strength = DRIVER_STRENGTH_33_OHM; |
| break; |
| case 66: |
| plat->drv_strength = DRIVER_STRENGTH_66_OHM; |
| break; |
| case 100: |
| plat->drv_strength = DRIVER_STRENGTH_100_OHM; |
| break; |
| case 40: |
| plat->drv_strength = DRIVER_STRENGTH_40_OHM; |
| break; |
| default: |
| dev_err(dev, "Invalid driver strength\n"); |
| return -EINVAL; |
| } |
| } |
| |
| dev_read_u32(dev, "ti,strobe-sel", &plat->strb_sel); |
| dev_read_u32(dev, "ti,clkbuf-sel", &plat->clkbuf_sel); |
| |
| ret = mmc_of_parse(dev, cfg); |
| if (ret) |
| return ret; |
| |
| return 0; |
| } |
| |
| static int am654_sdhci_bind(struct udevice *dev) |
| { |
| struct am654_driver_data *drv_data = |
| (struct am654_driver_data *)dev_get_driver_data(dev); |
| struct am654_sdhci_plat *plat = dev_get_plat(dev); |
| const struct soc_attr *soc; |
| const struct am654_driver_data *soc_drv_data; |
| |
| plat->flags = drv_data->flags; |
| |
| /* Update flags based on SoC revision */ |
| soc = soc_device_match(am654_sdhci_soc_attr); |
| if (soc && soc->data) { |
| soc_drv_data = soc->data; |
| plat->flags = soc_drv_data->flags; |
| } |
| |
| return sdhci_bind(dev, &plat->mmc, &plat->cfg); |
| } |
| |
| static const struct udevice_id am654_sdhci_ids[] = { |
| { |
| .compatible = "ti,am654-sdhci-5.1", |
| .data = (ulong)&am654_drv_data, |
| }, |
| { |
| .compatible = "ti,j721e-sdhci-8bit", |
| .data = (ulong)&j721e_8bit_drv_data, |
| }, |
| { |
| .compatible = "ti,j721e-sdhci-4bit", |
| .data = (ulong)&j721e_4bit_drv_data, |
| }, |
| { |
| .compatible = "ti,am64-sdhci-8bit", |
| .data = (ulong)&sdhci_am64_8bit_drvdata, |
| }, |
| { |
| .compatible = "ti,am64-sdhci-4bit", |
| .data = (ulong)&sdhci_am64_4bit_drvdata, |
| }, |
| { |
| .compatible = "ti,am62-sdhci", |
| .data = (ulong)&sdhci_am64_4bit_drvdata, |
| }, |
| { } |
| }; |
| |
| U_BOOT_DRIVER(am654_sdhci_drv) = { |
| .name = "am654_sdhci", |
| .id = UCLASS_MMC, |
| .of_match = am654_sdhci_ids, |
| .of_to_plat = am654_sdhci_of_to_plat, |
| .ops = &sdhci_ops, |
| .bind = am654_sdhci_bind, |
| .probe = am654_sdhci_probe, |
| .priv_auto = sizeof(struct sdhci_host), |
| .plat_auto = sizeof(struct am654_sdhci_plat), |
| }; |