CONFIG_ARM=y
CONFIG_ARCH_IMX8M=y
CONFIG_SYS_TEXT_BASE=0x40200000
CONFIG_SYS_MALLOC_LEN=0x600000
CONFIG_SYS_MALLOC_F_LEN=0x4000
CONFIG_SPL_GPIO=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_ENV_SIZE=0x1000
CONFIG_ENV_OFFSET=0x400000
CONFIG_SYS_I2C_MXC_I2C1=y
CONFIG_SYS_I2C_MXC_I2C2=y
CONFIG_SYS_I2C_MXC_I2C3=y
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="imx8mq-phanbell"
CONFIG_SPL_TEXT_BASE=0x7E1000
CONFIG_TARGET_IMX8MQ_PHANBELL=y
CONFIG_SPL_MMC=y
CONFIG_SPL_SERIAL=y
CONFIG_SPL_DRIVERS_MISC=y
CONFIG_SPL=y
CONFIG_IMX_BOOTAUX=y
CONFIG_SYS_LOAD_ADDR=0x40480000
CONFIG_FIT=y
CONFIG_FIT_EXTERNAL_OFFSET=0x3000
CONFIG_SPL_LOAD_FIT=y
CONFIG_SPL_FIT_GENERATOR="arch/arm/mach-imx/mkimage_fit_atf.sh"
CONFIG_SD_BOOT=y
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; then run bootscript; else if run loadimage; then run mmcboot; else run netboot; fi; fi; else booti ${loadaddr} - ${fdt_addr}; fi"
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_BOARD_INIT=y
CONFIG_SPL_I2C=y
CONFIG_SPL_POWER=y
CONFIG_HUSH_PARSER=y
# CONFIG_BOOTM_NETBSD is not set
# CONFIG_CMD_EXPORTENV is not set
# CONFIG_CMD_IMPORTENV is not set
# CONFIG_CMD_CRC32 is not set
CONFIG_CMD_FUSE=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_REGULATOR=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
# CONFIG_SPL_DOS_PARTITION is not set
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_SAVED_DRAM_TIMING_BASE=0x40000000
CONFIG_DM_I2C=y
CONFIG_SPL_SYS_I2C_LEGACY=y
CONFIG_SUPPORT_EMMC_BOOT=y
CONFIG_FSL_USDHC=y
CONFIG_PHYLIB=y
CONFIG_DM_ETH=y
CONFIG_PHY_GIGE=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX8M=y
CONFIG_SPL_POWER_LEGACY=y
CONFIG_POWER_DOMAIN=y
CONFIG_IMX8M_POWER_DOMAIN=y
CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_SPL_POWER_I2C=y
CONFIG_DM_RESET=y
CONFIG_MXC_UART=y
CONFIG_DM_THERMAL=y