85xx: convert SBC8540/SBC8560/SBC8548 over to use new LAW init code
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
diff --git a/board/sbc8548/Makefile b/board/sbc8548/Makefile
index 1596525..c346fdf 100644
--- a/board/sbc8548/Makefile
+++ b/board/sbc8548/Makefile
@@ -28,9 +28,8 @@
LIB = $(obj)lib$(BOARD).a
-COBJS := $(BOARD).o
+COBJS := $(BOARD).o law.o
SOBJS := init.o
-#SOBJS :=
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
diff --git a/board/sbc8548/init.S b/board/sbc8548/init.S
index cafa214..6696dd9 100644
--- a/board/sbc8548/init.S
+++ b/board/sbc8548/init.S
@@ -191,51 +191,3 @@
.long FSL_BOOKE_MAS3(CFG_EPLD_BASE, 0, (MAS3_SX|MAS3_SW|MAS3_SR))
entry_end
-
-/*
- * LAW(Local Access Window) configuration:
- *
- * 0x0000_0000 0x0fff_ffff DDR 256M
- * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M
- * 0xe000_0000 0xe000_ffff CCSR 1M
- * 0xe200_0000 0xe2ff_ffff PCI1 IO 16M
- * 0xf000_0000 0xf7ff_ffff SDRAM 128M
- * 0xf8b0_0000 0xf80f_ffff EEPROM 1M
- * 0xfb80_0000 0xff7f_ffff FLASH (2nd bank) 64M
- * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M
- *
- * Notes:
- * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
- * If flash is 8M at default position (last 8M), no LAW needed.
- *
- * The defines below are 1-off of the actual LAWAR0 usage.
- * So LAWAR3 define uses the LAWAR4 register in the ECM.
- */
-
-
-#if !defined(CONFIG_SPD_EEPROM)
- #define LAWBAR0 ((CFG_DDR_SDRAM_BASE>>12) & 0xfffff)
- #define LAWAR0 (LAWAR_EN | LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_256M))
-#else
- #define LAWBAR0 0
- #define LAWAR0 ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_256M)) & ~LAWAR_EN)
-#endif
-
-#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
-#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M))
-
-#define LAWBAR2 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
-#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M))
-
-/* LBC window - maps 256M 0xf0000000 -> 0xffffffff */
-#define LAWBAR3 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff)
-#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M))
-
- .section .bootpg, "ax"
- .globl law_entry
-
-law_entry:
- entry_start
- .long 4
- .long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3
- entry_end
diff --git a/board/sbc8548/law.c b/board/sbc8548/law.c
new file mode 100644
index 0000000..6bf4199
--- /dev/null
+++ b/board/sbc8548/law.c
@@ -0,0 +1,57 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+/*
+ * LAW(Local Access Window) configuration:
+ *
+ * 0x0000_0000 0x0fff_ffff DDR 256M
+ * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M
+ * 0xe000_0000 0xe000_ffff CCSR 1M
+ * 0xe200_0000 0xe2ff_ffff PCI1 IO 16M
+ * 0xf000_0000 0xf7ff_ffff SDRAM 128M
+ * 0xf8b0_0000 0xf80f_ffff EEPROM 1M
+ * 0xfb80_0000 0xff7f_ffff FLASH (2nd bank) 64M
+ * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M
+ *
+ * Notes:
+ * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ * If flash is 8M at default position (last 8M), no LAW needed.
+ */
+
+struct law_entry law_table[] = {
+#ifndef CONFIG_SPD_EEPROM
+ SET_LAW_ENTRY(1, CFG_DDR_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_DDR),
+#endif
+ SET_LAW_ENTRY(2, CFG_PCI1_MEM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_PCI),
+ SET_LAW_ENTRY(3, CFG_PCI1_IO_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_PCI),
+ /* LBC window - maps 256M 0xf0000000 -> 0xffffffff */
+ SET_LAW_ENTRY(4, CFG_LBC_SDRAM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/sbc8560/Makefile b/board/sbc8560/Makefile
index 1596525..c346fdf 100644
--- a/board/sbc8560/Makefile
+++ b/board/sbc8560/Makefile
@@ -28,9 +28,8 @@
LIB = $(obj)lib$(BOARD).a
-COBJS := $(BOARD).o
+COBJS := $(BOARD).o law.o
SOBJS := init.o
-#SOBJS :=
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
diff --git a/board/sbc8560/init.S b/board/sbc8560/init.S
index 95cb85a..e149fbd 100644
--- a/board/sbc8560/init.S
+++ b/board/sbc8560/init.S
@@ -40,51 +40,6 @@
mtlr r1 ; \
blr ;
-
-/* LAW(Local Access Window) configuration:
- * 0000_0000-0800_0000: DDR(512M) -or- larger
- * c000_0000-cfff_ffff: PCI(256M)
- * d000_0000-dfff_ffff: RapidIO(256M)
- * e000_0000-ffff_ffff: localbus(512M)
- * e000_0000-e3ff_ffff: LBC 64M, 32-bit flash on CS6
- * e400_0000-e7ff_ffff: LBC 64M, 32-bit flash on CS1
- * e800_0000-efff_ffff: LBC 128M, nothing here
- * f000_0000-f3ff_ffff: LBC 64M, SDRAM on CS3
- * f400_0000-f7ff_ffff: LBC 64M, SDRAM on CS4
- * f800_0000-fdff_ffff: LBC 64M, nothing here
- * fc00_0000-fcff_ffff: LBC 16M, CSR,RTC,UART,etc on CS5
- * fd00_0000-fdff_ffff: LBC 16M, nothing here
- * fe00_0000-feff_ffff: LBC 16M, nothing here
- * ff00_0000-ff6f_ffff: LBC 7M, nothing here
- * ff70_0000-ff7f_ffff: CCSRBAR 1M
- * ff80_0000-ffff_ffff: LBC 8M, 8-bit flash on CS0
- * Note: CCSRBAR and L2-as-SRAM don't need configure Local Access
- * Window.
- * Note: If flash is 8M at default position(last 8M),no LAW needed.
- */
-
-#if !defined(CONFIG_SPD_EEPROM)
- #define LAWBAR0 ((CFG_DDR_SDRAM_BASE>>12) & 0xfffff)
- #define LAWAR0 (LAWAR_EN | LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_512M))
-#else
- #define LAWBAR0 0
- #define LAWAR0 ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_512M)) & ~LAWAR_EN)
-#endif
-
-#define LAWBAR1 ((CFG_PCI_MEM_BASE>>12) & 0xfffff)
-#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_256M))
-
-#define LAWBAR2 ((0xe0000000>>12) & 0xfffff)
-#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_512M))
-
- .section .bootpg, "ax"
- .globl law_entry
-law_entry:
- entry_start
- .long 0x03
- .long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2
- entry_end
-
/* TLB1 entries configuration: */
.section .bootpg, "ax"
diff --git a/board/sbc8560/law.c b/board/sbc8560/law.c
new file mode 100644
index 0000000..d1c6dc2
--- /dev/null
+++ b/board/sbc8560/law.c
@@ -0,0 +1,60 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+/* LAW(Local Access Window) configuration:
+ * 0000_0000-0800_0000: DDR(512M) -or- larger
+ * c000_0000-cfff_ffff: PCI(256M)
+ * d000_0000-dfff_ffff: RapidIO(256M)
+ * e000_0000-ffff_ffff: localbus(512M)
+ * e000_0000-e3ff_ffff: LBC 64M, 32-bit flash on CS6
+ * e400_0000-e7ff_ffff: LBC 64M, 32-bit flash on CS1
+ * e800_0000-efff_ffff: LBC 128M, nothing here
+ * f000_0000-f3ff_ffff: LBC 64M, SDRAM on CS3
+ * f400_0000-f7ff_ffff: LBC 64M, SDRAM on CS4
+ * f800_0000-fdff_ffff: LBC 64M, nothing here
+ * fc00_0000-fcff_ffff: LBC 16M, CSR,RTC,UART,etc on CS5
+ * fd00_0000-fdff_ffff: LBC 16M, nothing here
+ * fe00_0000-feff_ffff: LBC 16M, nothing here
+ * ff00_0000-ff6f_ffff: LBC 7M, nothing here
+ * ff70_0000-ff7f_ffff: CCSRBAR 1M
+ * ff80_0000-ffff_ffff: LBC 8M, 8-bit flash on CS0
+ * Note: CCSRBAR and L2-as-SRAM don't need configure Local Access
+ * Window.
+ * Note: If flash is 8M at default position(last 8M),no LAW needed.
+ */
+
+struct law_entry law_table[] = {
+#ifndef CONFIG_SPD_EEPROM
+ SET_LAW_ENTRY(1, CFG_DDR_SDRAM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_DDR),
+#endif
+ SET_LAW_ENTRY(2, CFG_PCI_MEM_BASE, LAW_SIZE_256M, LAW_TRGT_IF_PCI),
+ SET_LAW_ENTRY(3, CFG_LBC_SDRAM_BASE, LAW_SIZE_512M, LAW_TRGT_IF_LBC),
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h
index 3ca85b8..2bbfe9a 100644
--- a/include/configs/SBC8540.h
+++ b/include/configs/SBC8540.h
@@ -56,6 +56,7 @@
#undef CONFIG_PCI /* pci ethernet support */
#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
#define CONFIG_ENV_OVERWRITE
diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h
index c050a06..0a7a904 100644
--- a/include/configs/sbc8548.h
+++ b/include/configs/sbc8548.h
@@ -56,6 +56,7 @@
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */
diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h
index b71ba78..f9ede5f 100644
--- a/include/configs/sbc8560.h
+++ b/include/configs/sbc8560.h
@@ -50,6 +50,7 @@
#undef CONFIG_PCI /* pci ethernet support */
#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
#define CONFIG_ENV_OVERWRITE