diff --git a/board/renesas/koelsch/Makefile b/board/renesas/koelsch/Makefile
index 15f111c..77cf067 100644
--- a/board/renesas/koelsch/Makefile
+++ b/board/renesas/koelsch/Makefile
@@ -6,4 +6,8 @@
 # SPDX-License-Identifier: GPL-2.0
 #
 
-obj-y	:= koelsch.o qos.o ../rcar-common/common.o
+ifdef CONFIG_SPL_BUILD
+obj-y	:= koelsch_spl.o
+else
+obj-y	:= koelsch.o qos.o
+endif
diff --git a/board/renesas/koelsch/koelsch.c b/board/renesas/koelsch/koelsch.c
index e7b47ae..4a4007b 100644
--- a/board/renesas/koelsch/koelsch.c
+++ b/board/renesas/koelsch/koelsch.c
@@ -48,13 +48,7 @@
 	qos_init();
 }
 
-#define TMU0_MSTP125	(1 << 25)
-#define SCIF0_MSTP721	(1 << 21)
-#define ETHER_MSTP813	(1 << 13)
-
-#define SDHI0_MSTP314	(1 << 14)
-#define SDHI1_MSTP312	(1 << 12)
-#define SDHI2_MSTP311	(1 << 11)
+#define TMU0_MSTP125	BIT(25)
 
 #define SD1CKCR		0xE6150078
 #define SD2CKCR		0xE615026C
@@ -64,16 +58,6 @@
 {
 	mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125);
 
-	/* SCIF0 */
-	mstp_clrbits_le32(MSTPSR7, SMSTPCR7, SCIF0_MSTP721);
-
-	/* ETHER */
-	mstp_clrbits_le32(MSTPSR8, SMSTPCR8, ETHER_MSTP813);
-
-	/* SDHI  */
-	mstp_clrbits_le32(MSTPSR3, SMSTPCR3,
-			  SDHI0_MSTP314 | SDHI1_MSTP312 | SDHI2_MSTP311);
-
 	/*
 	 * SD0 clock is set to 97.5MHz by default.
 	 * Set SD1 and SD2 to the 97.5MHz as well.
@@ -84,133 +68,40 @@
 	return 0;
 }
 
+#define ETHERNET_PHY_RESET	176	/* GPIO 5 22 */
+
-/* LSI pin pull-up control */
-#define PUPR5 0xe6060114
-#define PUPR5_ETH 0x3FFC0000
-#define PUPR5_ETH_MAGIC	(1 << 27)
 int board_init(void)
 {
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 
-	/* Init PFC controller */
-	r8a7791_pinmux_init();
-
-	/* ETHER Enable */
-	gpio_request(GPIO_FN_ETH_CRS_DV, NULL);
-	gpio_request(GPIO_FN_ETH_RX_ER, NULL);
-	gpio_request(GPIO_FN_ETH_RXD0, NULL);
-	gpio_request(GPIO_FN_ETH_RXD1, NULL);
-	gpio_request(GPIO_FN_ETH_LINK, NULL);
-	gpio_request(GPIO_FN_ETH_REFCLK, NULL);
-	gpio_request(GPIO_FN_ETH_MDIO, NULL);
-	gpio_request(GPIO_FN_ETH_TXD1, NULL);
-	gpio_request(GPIO_FN_ETH_TX_EN, NULL);
-	gpio_request(GPIO_FN_ETH_TXD0, NULL);
-	gpio_request(GPIO_FN_ETH_MDC, NULL);
-	gpio_request(GPIO_FN_IRQ0, NULL);
-
-	mstp_clrbits_le32(PUPR5, PUPR5, PUPR5_ETH & ~PUPR5_ETH_MAGIC);
-	gpio_request(GPIO_GP_5_22, NULL); /* PHY_RST */
-	mstp_clrbits_le32(PUPR5, PUPR5, PUPR5_ETH_MAGIC);
-
-	gpio_direction_output(GPIO_GP_5_22, 0);
-	mdelay(20);
-	gpio_set_value(GPIO_GP_5_22, 1);
-	udelay(1);
+	/* Force ethernet PHY out of reset */
+	gpio_request(ETHERNET_PHY_RESET, "phy_reset");
+	gpio_direction_output(ETHERNET_PHY_RESET, 0);
+	mdelay(10);
+	gpio_direction_output(ETHERNET_PHY_RESET, 1);
 
 	return 0;
 }
 
-#define CXR24 0xEE7003C0 /* MAC address high register */
-#define CXR25 0xEE7003C8 /* MAC address low register */
-int board_eth_init(bd_t *bis)
+int dram_init(void)
 {
-#ifdef CONFIG_SH_ETHER
-	int ret = -ENODEV;
-	u32 val;
-	unsigned char enetaddr[6];
+	if (fdtdec_setup_memory_size() != 0)
+		return -EINVAL;
 
-	ret = sh_eth_initialize(bis);
-	if (!eth_env_get_enetaddr("ethaddr", enetaddr))
-		return ret;
-
-	/* Set Mac address */
-	val = enetaddr[0] << 24 | enetaddr[1] << 16 |
-		enetaddr[2] << 8 | enetaddr[3];
-	writel(val, CXR24);
-
-	val = enetaddr[4] << 8 | enetaddr[5];
-	writel(val, CXR25);
-
-	return ret;
-#else
 	return 0;
-#endif
 }
 
-int board_mmc_init(bd_t *bis)
+int dram_init_banksize(void)
 {
-	int ret = -ENODEV;
-
-#ifdef CONFIG_SH_SDHI
-	gpio_request(GPIO_FN_SD0_DATA0, NULL);
-	gpio_request(GPIO_FN_SD0_DATA1, NULL);
-	gpio_request(GPIO_FN_SD0_DATA2, NULL);
-	gpio_request(GPIO_FN_SD0_DATA3, NULL);
-	gpio_request(GPIO_FN_SD0_CLK, NULL);
-	gpio_request(GPIO_FN_SD0_CMD, NULL);
-	gpio_request(GPIO_FN_SD0_CD, NULL);
-	gpio_request(GPIO_FN_SD2_DATA0, NULL);
-	gpio_request(GPIO_FN_SD2_DATA1, NULL);
-	gpio_request(GPIO_FN_SD2_DATA2, NULL);
-	gpio_request(GPIO_FN_SD2_DATA3, NULL);
-	gpio_request(GPIO_FN_SD2_CLK, NULL);
-	gpio_request(GPIO_FN_SD2_CMD, NULL);
-	gpio_request(GPIO_FN_SD2_CD, NULL);
-
-	/* SDHI 0 */
-	gpio_request(GPIO_GP_7_17, NULL);
-	gpio_request(GPIO_GP_2_12, NULL);
-	gpio_direction_output(GPIO_GP_7_17, 1); /* power on */
-	gpio_direction_output(GPIO_GP_2_12, 1); /* 1: 3.3V, 0: 1.8V */
-
-	ret = sh_sdhi_init(CONFIG_SYS_SH_SDHI0_BASE, 0,
-			   SH_SDHI_QUIRK_16BIT_BUF);
-	if (ret)
-		return ret;
-
-	/* SDHI 1 */
-	gpio_request(GPIO_GP_7_18, NULL);
-	gpio_request(GPIO_GP_2_13, NULL);
-	gpio_direction_output(GPIO_GP_7_18, 1); /* power on */
-	gpio_direction_output(GPIO_GP_2_13, 1); /* 1: 3.3V, 0: 1.8V */
-
-	ret = sh_sdhi_init(CONFIG_SYS_SH_SDHI1_BASE, 1, 0);
-	if (ret)
-		return ret;
-
-	/* SDHI 2 */
-	gpio_request(GPIO_GP_7_19, NULL);
-	gpio_request(GPIO_GP_2_26, NULL);
-	gpio_direction_output(GPIO_GP_7_19, 1); /* power on */
-	gpio_direction_output(GPIO_GP_2_26, 1); /* 1: 3.3V, 0: 1.8V */
-
-	ret = sh_sdhi_init(CONFIG_SYS_SH_SDHI2_BASE, 2, 0);
-#endif
-	return ret;
-}
-
-int dram_init(void)
-{
-	gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
+	fdtdec_setup_memory_banksize();
 
 	return 0;
 }
 
-/* koelsch has KSZ8041NL/RNL */
-#define PHY_CONTROL1	0x1E
-#define PHY_LED_MODE	0xC0000
+/* Koelsch has KSZ8041NL/RNL */
+#define PHY_CONTROL1		0x1E
+#define PHY_LED_MODE		0xC0000
 #define PHY_LED_MODE_ACK	0x4000
 int board_phy_config(struct phy_device *phydev)
 {
@@ -228,22 +119,38 @@
 
 void reset_cpu(ulong addr)
 {
-	u8 val;
+	struct udevice *dev;
+	const u8 pmic_bus = 6;
+	const u8 pmic_addr = 0x58;
+	u8 data;
+	int ret;
+
+	ret = i2c_get_chip_for_busnum(pmic_bus, pmic_addr, 1, &dev);
+	if (ret)
+		hang();
+
+	ret = dm_i2c_read(dev, 0x13, &data, 1);
+	if (ret)
+		hang();
+
+	data |= BIT(1);
 
-	i2c_set_bus_num(2); /* PowerIC connected to ch2 */
-	i2c_read(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1);
-	val |= 0x02;
-	i2c_write(CONFIG_SYS_I2C_POWERIC_ADDR, 0x13, 1, &val, 1);
+	ret = dm_i2c_write(dev, 0x13, &data, 1);
+	if (ret)
+		hang();
 }
 
-static const struct sh_serial_platdata serial_platdata = {
-	.base = SCIF0_BASE,
-	.type = PORT_SCIF,
-	.clk = 14745600,
-	.clk_mode = EXT_CLK,
-};
+enum env_location env_get_location(enum env_operation op, int prio)
+{
+	const u32 load_magic = 0xb33fc0de;
 
-U_BOOT_DEVICE(koelsch_serials) = {
-	.name = "serial_sh",
-	.platdata = &serial_platdata,
-};
+	/* Block environment access if loaded using JTAG */
+	if ((readl(CONFIG_SPL_TEXT_BASE + 0x24) == load_magic) &&
+	    (op != ENVOP_INIT))
+		return ENVL_UNKNOWN;
+
+	if (prio)
+		return ENVL_UNKNOWN;
+
+	return ENVL_SPI_FLASH;
+}
diff --git a/board/renesas/koelsch/koelsch_spl.c b/board/renesas/koelsch/koelsch_spl.c
new file mode 100644
index 0000000..de6c1c0
--- /dev/null
+++ b/board/renesas/koelsch/koelsch_spl.c
@@ -0,0 +1,410 @@
+/*
+ * board/renesas/koelsch/koelsch_spl.c
+ *
+ * Copyright (C) 2018 Marek Vasut <marek.vasut@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <dm/platform_data/serial_sh.h>
+#include <asm/processor.h>
+#include <asm/mach-types.h>
+#include <asm/io.h>
+#include <linux/errno.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/arch/rmobile.h>
+#include <asm/arch/rcar-mstp.h>
+
+#include <spl.h>
+
+#define TMU0_MSTP125	BIT(25)
+#define SCIF0_MSTP721	BIT(21)
+#define QSPI_MSTP917	BIT(17)
+
+#define SD2CKCR		0xE615026C
+#define SD_97500KHZ	0x7
+
+struct reg_config {
+	u16	off;
+	u32	val;
+};
+
+static void dbsc_wait(u16 reg)
+{
+	static const u32 dbsc3_0_base = DBSC3_0_BASE;
+	static const u32 dbsc3_1_base = DBSC3_0_BASE + 0x10000;
+
+	while (!(readl(dbsc3_0_base + reg) & BIT(0)))
+		;
+
+	while (!(readl(dbsc3_1_base + reg) & BIT(0)))
+		;
+}
+
+static void spl_init_sys(void)
+{
+	u32 r0 = 0;
+
+	writel(0xa5a5a500, 0xe6020004);
+	writel(0xa5a5a500, 0xe6030004);
+
+	asm volatile(
+		/* ICIALLU - Invalidate I$ to PoU */
+		"mcr	15, 0, %0, cr7, cr5, 0	\n"
+		/* BPIALL - Invalidate branch predictors */
+		"mcr	15, 0, %0, cr7, cr5, 6	\n"
+		/* Set SCTLR[IZ] */
+		"mrc	15, 0, %0, cr1, cr0, 0	\n"
+		"orr	%0, #0x1800		\n"
+		"mcr	15, 0, %0, cr1, cr0, 0	\n"
+		"isb	sy			\n"
+		:"=r"(r0));
+}
+
+static void spl_init_pfc(void)
+{
+	static const struct reg_config pfc_with_unlock[] = {
+		{ 0x0090, 0x60000000 },
+		{ 0x0094, 0x60000000 },
+		{ 0x0098, 0x00800200 },
+		{ 0x009c, 0x00000000 },
+		{ 0x0020, 0x00000000 },
+		{ 0x0024, 0x00000000 },
+		{ 0x0028, 0x000244c8 },
+		{ 0x002c, 0x00000000 },
+		{ 0x0030, 0x00002400 },
+		{ 0x0034, 0x01520000 },
+		{ 0x0038, 0x00724003 },
+		{ 0x003c, 0x00000000 },
+		{ 0x0040, 0x00000000 },
+		{ 0x0044, 0x00000000 },
+		{ 0x0048, 0x00000000 },
+		{ 0x004c, 0x00000000 },
+		{ 0x0050, 0x00000000 },
+		{ 0x0054, 0x00000000 },
+		{ 0x0058, 0x00000000 },
+		{ 0x005c, 0x00000000 },
+		{ 0x0160, 0x00000000 },
+		{ 0x0004, 0xffffffff },
+		{ 0x0008, 0x00ec3fff },
+		{ 0x000c, 0x3bc001e7 },
+		{ 0x0010, 0x5bffffff },
+		{ 0x0014, 0x1ffffffb },
+		{ 0x0018, 0x01bffff0 },
+		{ 0x001c, 0xcf7fffff },
+		{ 0x0074, 0x0381fc00 },
+	};
+
+	static const struct reg_config pfc_without_unlock[] = {
+		{ 0x0100, 0xffffffdf },
+		{ 0x0104, 0xc883c3ff },
+		{ 0x0108, 0x1201f3c9 },
+		{ 0x010c, 0x00000000 },
+		{ 0x0110, 0xffffeb04 },
+		{ 0x0114, 0xc003ffff },
+		{ 0x0118, 0x0800000f },
+		{ 0x011c, 0x001800f0 },
+	};
+
+	static const u32 pfc_base = 0xe6060000;
+
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(pfc_with_unlock); i++) {
+		writel(~pfc_with_unlock[i].val, pfc_base);
+		writel(pfc_with_unlock[i].val,
+		       pfc_base | pfc_with_unlock[i].off);
+	}
+
+	for (i = 0; i < ARRAY_SIZE(pfc_without_unlock); i++)
+		writel(pfc_without_unlock[i].val,
+		       pfc_base | pfc_without_unlock[i].off);
+}
+
+static void spl_init_gpio(void)
+{
+	static const u16 gpio_offs[] = {
+		0x1000, 0x2000, 0x3000, 0x4000, 0x5000, 0x5400, 0x5800
+	};
+
+	static const struct reg_config gpio_set[] = {
+		{ 0x2000, 0x04381000 },
+		{ 0x5000, 0x00000000 },
+		{ 0x5800, 0x000e0000 },
+
+	};
+
+	static const struct reg_config gpio_clr[] = {
+		{ 0x1000, 0x00000000 },
+		{ 0x2000, 0x04381010 },
+		{ 0x3000, 0x00000000 },
+		{ 0x4000, 0x00000000 },
+		{ 0x5000, 0x00400000 },
+		{ 0x5400, 0x00000000 },
+		{ 0x5800, 0x000e0380 },
+	};
+
+	static const u32 gpio_base = 0xe6050000;
+
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(gpio_offs); i++)
+		writel(0, gpio_base | 0x20 | gpio_offs[i]);
+
+	for (i = 0; i < ARRAY_SIZE(gpio_offs); i++)
+		writel(0, gpio_base | 0x00 | gpio_offs[i]);
+
+	for (i = 0; i < ARRAY_SIZE(gpio_set); i++)
+		writel(gpio_set[i].val, gpio_base | 0x08 | gpio_set[i].off);
+
+	for (i = 0; i < ARRAY_SIZE(gpio_clr); i++)
+		writel(gpio_clr[i].val, gpio_base | 0x04 | gpio_clr[i].off);
+}
+
+static void spl_init_lbsc(void)
+{
+	static const struct reg_config lbsc_config[] = {
+		{ 0x00, 0x00000020 },
+		{ 0x08, 0x00002020 },
+		{ 0x30, 0x2a103320 },
+		{ 0x38, 0xff70ff70 },
+	};
+
+	static const u16 lbsc_offs[] = {
+		0x80, 0x84, 0x88, 0x8c, 0xa0, 0xc0, 0xc4, 0xc8, 0x180
+	};
+
+	static const u32 lbsc_base = 0xfec00200;
+
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(lbsc_config); i++) {
+		writel(lbsc_config[i].val,
+		       lbsc_base | lbsc_config[i].off);
+		writel(lbsc_config[i].val,
+		       lbsc_base | (lbsc_config[i].off + 4));
+	}
+
+	for (i = 0; i < ARRAY_SIZE(lbsc_offs); i++)
+		writel(0, lbsc_base | lbsc_offs[i]);
+}
+
+static void spl_init_dbsc(void)
+{
+	static const struct reg_config dbsc_config1[] = {
+		{ 0x0018, 0x21000000 },
+		{ 0x0018, 0x11000000 },
+		{ 0x0018, 0x10000000 },
+		{ 0x0280, 0x0000a55a },
+		{ 0x0290, 0x00000010 },
+		{ 0x02a0, 0xf004649b },
+		{ 0x0020, 0x00000007 },
+		{ 0x0024, 0x0f030a02 },
+		{ 0x0030, 0x00000001 },
+		{ 0x00b0, 0x00000000 },
+		{ 0x0040, 0x0000000b },
+		{ 0x0044, 0x00000008 },
+		{ 0x0048, 0x00000000 },
+		{ 0x0050, 0x0000000b },
+		{ 0x0054, 0x000c000b },
+		{ 0x0058, 0x00000027 },
+		{ 0x005c, 0x0000001c },
+		{ 0x0060, 0x00000006 },
+		{ 0x0064, 0x00000020 },
+		{ 0x0068, 0x00000008 },
+		{ 0x006c, 0x0000000c },
+		{ 0x0070, 0x00000009 },
+		{ 0x0074, 0x00000012 },
+		{ 0x0078, 0x000000d0 },
+		{ 0x007c, 0x00140005 },
+		{ 0x0080, 0x00050004 },
+		{ 0x0084, 0x70233005 },
+		{ 0x0088, 0x000c0000 },
+		{ 0x008c, 0x00000300 },
+		{ 0x0090, 0x00000040 },
+		{ 0x0100, 0x00000001 },
+		{ 0x00c0, 0x00020001 },
+		{ 0x00c8, 0x20082008 },
+		{ 0x0380, 0x00020002 },
+		{ 0x0390, 0x0000001f },
+	};
+
+	static const struct reg_config dbsc_config5[] = {
+		{ 0x0244, 0x00000011 },
+		{ 0x0290, 0x00000006 },
+		{ 0x02a0, 0x0005c000 },
+		{ 0x0290, 0x00000003 },
+		{ 0x02a0, 0x0300c481 },
+		{ 0x0290, 0x00000023 },
+		{ 0x02a0, 0x00fdb6c0 },
+		{ 0x0290, 0x00000011 },
+		{ 0x02a0, 0x1000040b },
+		{ 0x0290, 0x00000012 },
+		{ 0x02a0, 0x9d9cbb66 },
+		{ 0x0290, 0x00000013 },
+		{ 0x02a0, 0x1a868400 },
+		{ 0x0290, 0x00000014 },
+		{ 0x02a0, 0x300214d8 },
+		{ 0x0290, 0x00000015 },
+		{ 0x02a0, 0x00000d70 },
+		{ 0x0290, 0x00000016 },
+		{ 0x02a0, 0x00000006 },
+		{ 0x0290, 0x00000017 },
+		{ 0x02a0, 0x00000018 },
+		{ 0x0290, 0x0000001a },
+		{ 0x02a0, 0x910035c7 },
+		{ 0x0290, 0x00000004 },
+	};
+
+	static const struct reg_config dbsc_config6[] = {
+		{ 0x0290, 0x00000001 },
+		{ 0x02a0, 0x00000181 },
+		{ 0x0018, 0x11000000 },
+		{ 0x0290, 0x00000004 },
+	};
+
+	static const struct reg_config dbsc_config7[] = {
+		{ 0x0290, 0x00000001 },
+		{ 0x02a0, 0x0000fe01 },
+		{ 0x0290, 0x00000004 },
+	};
+
+	static const struct reg_config dbsc_config8[] = {
+		{ 0x0304, 0x00000000 },
+		{ 0x00f4, 0x01004c20 },
+		{ 0x00f8, 0x014000aa },
+		{ 0x00e0, 0x00000140 },
+		{ 0x00e4, 0x00081860 },
+		{ 0x00e8, 0x00010000 },
+		{ 0x0014, 0x00000001 },
+		{ 0x0010, 0x00000001 },
+		{ 0x0280, 0x00000000 },
+	};
+
+	static const u32 dbsc3_0_base = DBSC3_0_BASE;
+	static const u32 dbsc3_1_base = DBSC3_0_BASE + 0x10000;
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(dbsc_config1); i++) {
+		writel(dbsc_config1[i].val, dbsc3_0_base | dbsc_config1[i].off);
+		writel(dbsc_config1[i].val, dbsc3_1_base | dbsc_config1[i].off);
+	}
+
+	dbsc_wait(0x240);
+
+	for (i = 0; i < ARRAY_SIZE(dbsc_config5); i++) {
+		writel(dbsc_config5[i].val, dbsc3_0_base | dbsc_config5[i].off);
+		writel(dbsc_config5[i].val, dbsc3_1_base | dbsc_config5[i].off);
+	}
+
+	dbsc_wait(0x2a0);
+
+	for (i = 0; i < ARRAY_SIZE(dbsc_config6); i++) {
+		writel(dbsc_config6[i].val, dbsc3_0_base | dbsc_config6[i].off);
+		writel(dbsc_config6[i].val, dbsc3_1_base | dbsc_config6[i].off);
+	}
+
+	dbsc_wait(0x2a0);
+
+	for (i = 0; i < ARRAY_SIZE(dbsc_config7); i++) {
+		writel(dbsc_config7[i].val, dbsc3_0_base | dbsc_config7[i].off);
+		writel(dbsc_config7[i].val, dbsc3_1_base | dbsc_config7[i].off);
+	}
+
+	dbsc_wait(0x2a0);
+
+	for (i = 0; i < ARRAY_SIZE(dbsc_config8); i++) {
+		writel(dbsc_config8[i].val, dbsc3_0_base | dbsc_config8[i].off);
+		writel(dbsc_config8[i].val, dbsc3_1_base | dbsc_config8[i].off);
+	}
+
+}
+
+static void spl_init_qspi(void)
+{
+	mstp_clrbits_le32(MSTPSR9, SMSTPCR9, QSPI_MSTP917);
+
+	static const u32 qspi_base = 0xe6b10000;
+
+	writeb(0x08, qspi_base + 0x00);
+	writeb(0x00, qspi_base + 0x01);
+	writeb(0x06, qspi_base + 0x02);
+	writeb(0x01, qspi_base + 0x0a);
+	writeb(0x00, qspi_base + 0x0b);
+	writeb(0x00, qspi_base + 0x0c);
+	writeb(0x00, qspi_base + 0x0d);
+	writeb(0x00, qspi_base + 0x0e);
+
+	writew(0xe080, qspi_base + 0x10);
+
+	writeb(0xc0, qspi_base + 0x18);
+	writeb(0x00, qspi_base + 0x18);
+	writeb(0x00, qspi_base + 0x08);
+	writeb(0x48, qspi_base + 0x00);
+}
+
+void board_init_f(ulong dummy)
+{
+	int i;
+
+	mstp_clrbits_le32(MSTPSR1, SMSTPCR1, TMU0_MSTP125);
+	mstp_clrbits_le32(MSTPSR7, SMSTPCR7, SCIF0_MSTP721);
+
+	/*
+	 * SD0 clock is set to 97.5MHz by default.
+	 * Set SD2 to the 97.5MHz as well.
+	 */
+	writel(SD_97500KHZ, SD2CKCR);
+
+	spl_init_sys();
+	spl_init_pfc();
+	spl_init_gpio();
+	spl_init_lbsc();
+
+	/* Unknown, likely ES1.0-specific delay */
+	for (i = 0; i < 100000; i++)
+		asm volatile("nop");
+
+	spl_init_dbsc();
+	spl_init_qspi();
+}
+
+void spl_board_init(void)
+{
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+}
+
+void board_boot_order(u32 *spl_boot_list)
+{
+	const u32 jtag_magic = 0x1337c0de;
+	const u32 load_magic = 0xb33fc0de;
+
+	/*
+	 * If JTAG probe sets special word at 0xe6300020, then it must
+	 * put U-Boot into RAM and SPL will start it from RAM.
+	 */
+	if (readl(CONFIG_SPL_TEXT_BASE + 0x20) == jtag_magic) {
+		printf("JTAG boot detected!\n");
+
+		while (readl(CONFIG_SPL_TEXT_BASE + 0x24) != load_magic)
+			;
+
+		spl_boot_list[0] = BOOT_DEVICE_RAM;
+		spl_boot_list[1] = BOOT_DEVICE_NONE;
+
+		return;
+	}
+
+	/* Boot from SPI NOR with YMODEM UART fallback. */
+	spl_boot_list[0] = BOOT_DEVICE_SPI;
+	spl_boot_list[1] = BOOT_DEVICE_UART;
+	spl_boot_list[2] = BOOT_DEVICE_NONE;
+}
+
+void reset_cpu(ulong addr)
+{
+}