arm: dts: k3-am64: Sync DT with Linux v6.5-rc1
Sync all am642-evm/am642-sk related DT files
with Linux v6.5-rc1.
- drop timer1 in favor of main_timer0 in am64-main.dtsi.
Need to delete clock & power domain properties of
main_timer1 in -r5.dts else won't boot. This is because
timer_init is done during rproc_start to start System Firmware,
but we can't do any clock/power-domain operations before
System Firmware starts.
- same constraint applies to main_uart0
- drop cpsw3g custom DT property 'mac_efuse' and custom
DT node cpsw-phy-sel as driver picks these from standard
property/node.
- include board dts file in -r5 dts file to avoid duplication
of nodes. Include -u-boot.dtsi on top.
- drop duplicate nodes in -r5 dts and -u-boot.dtsi
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
diff --git a/arch/arm/dts/k3-am642-r5-sk.dts b/arch/arm/dts/k3-am642-r5-sk.dts
index 32d4c31..def4622 100644
--- a/arch/arm/dts/k3-am642-r5-sk.dts
+++ b/arch/arm/dts/k3-am642-r5-sk.dts
@@ -3,33 +3,18 @@
* Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
*/
-/dts-v1/;
-
-#include <dt-bindings/mux/ti-serdes.h>
-#include <dt-bindings/phy/phy.h>
-#include <dt-bindings/net/ti-dp83867.h>
-#include "k3-am642.dtsi"
+#include "k3-am642-sk.dts"
#include "k3-am64-sk-lp4-1600MTs.dtsi"
#include "k3-am64-ddr.dtsi"
-/ {
- chosen {
- stdout-path = "serial2:115200n8";
- tick-timer = &timer1;
- };
+#include "k3-am642-sk-u-boot.dtsi"
+/ {
aliases {
remoteproc0 = &sysctrler;
remoteproc1 = &a53_0;
};
- memory@80000000 {
- device_type = "memory";
- /* 2G RAM */
- reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
- bootph-pre-ram;
- };
-
a53_0: a53@0 {
compatible = "ti,am654-rproc";
reg = <0x00 0x00a90000 0x00 0x10>;
@@ -47,18 +32,6 @@
bootph-pre-ram;
};
- reserved-memory {
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- secure_ddr: optee@9e800000 {
- reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
- alignment = <0x1000>;
- no-map;
- };
- };
-
clk_200mhz: dummy-clock-200mhz {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -76,108 +49,12 @@
};
};
-&cbass_main {
- main_esm: esm@420000 {
- compatible = "ti,j721e-esm";
- reg = <0x0 0x420000 0x0 0x1000>;
- ti,esm-pins = <160>, <161>;
- bootph-pre-ram;
- };
-};
-
-&cbass_mcu {
+&main_esm {
bootph-pre-ram;
- mcu_esm: esm@4100000 {
- compatible = "ti,j721e-esm";
- reg = <0x0 0x4100000 0x0 0x1000>;
- ti,esm-pins = <0>, <1>;
- bootph-pre-ram;
- };
};
-&main_pmx0 {
+&mcu_esm {
bootph-pre-ram;
- main_uart0_pins_default: main-uart0-pins-default {
- bootph-pre-ram;
- pinctrl-single,pins = <
- AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */
- AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */
- AM64X_IOPAD(0x0230, PIN_INPUT, 0) /* (D15) UART0_RXD */
- AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* (C16) UART0_TXD */
- >;
- };
-
- main_uart1_pins_default: main-uart1-pins-default {
- bootph-pre-ram;
- pinctrl-single,pins = <
- AM64X_IOPAD(0x0248, PIN_INPUT, 0) /* (D16) UART1_CTSn */
- AM64X_IOPAD(0x024c, PIN_OUTPUT, 0) /* (E16) UART1_RTSn */
- AM64X_IOPAD(0x0240, PIN_INPUT, 0) /* (E15) UART1_RXD */
- AM64X_IOPAD(0x0244, PIN_OUTPUT, 0) /* (E14) UART1_TXD */
- >;
- };
-
- main_mmc1_pins_default: main-mmc1-pins-default {
- bootph-pre-ram;
- pinctrl-single,pins = <
- AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */
- AM64X_IOPAD(0x028c, PIN_INPUT_PULLDOWN, 0) /* (L20) MMC1_CLK */
- AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0) /* (K21) MMC1_DAT0 */
- AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0) /* (L21) MMC1_DAT1 */
- AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0) /* (K19) MMC1_DAT2 */
- AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0) /* (K18) MMC1_DAT3 */
- AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */
- AM64X_IOPAD(0x029c, PIN_INPUT_PULLUP, 0) /* (C20) MMC1_SDWP */
- >;
- };
-
- main_usb0_pins_default: main-usb0-pins-default {
- bootph-pre-ram;
- pinctrl-single,pins = <
- AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */
- >;
- };
-
- mdio1_pins_default: mdio1-pins-default {
- pinctrl-single,pins = <
- AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */
- AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */
- >;
- };
-
- rgmii1_pins_default: rgmii1-pins-default {
- pinctrl-single,pins = <
- AM64X_IOPAD(0x011c, PIN_INPUT, 4) /* (AA13) PRG1_PRU1_GPO5.RGMII1_RD0 */
- AM64X_IOPAD(0x0128, PIN_INPUT, 4) /* (U12) PRG1_PRU1_GPO8.RGMII1_RD1 */
- AM64X_IOPAD(0x0150, PIN_INPUT, 4) /* (Y13) PRG1_PRU1_GPO18.RGMII1_RD2 */
- AM64X_IOPAD(0x0154, PIN_INPUT, 4) /* (V12) PRG1_PRU1_GPO19.RGMII1_RD3 */
- AM64X_IOPAD(0x00d8, PIN_INPUT, 4) /* (W13) PRG1_PRU0_GPO8.RGMII1_RXC */
- AM64X_IOPAD(0x00cc, PIN_INPUT, 4) /* (V13) PRG1_PRU0_GPO5.RGMII1_RX_CTL */
- AM64X_IOPAD(0x0124, PIN_OUTPUT, 4) /* (V15) PRG1_PRU1_GPO7.RGMII1_TD0 */
- AM64X_IOPAD(0x012c, PIN_OUTPUT, 4) /* (V14) PRG1_PRU1_GPO9.RGMII1_TD1 */
- AM64X_IOPAD(0x0130, PIN_OUTPUT, 4) /* (W14) PRG1_PRU1_GPO10.RGMII1_TD2 */
- AM64X_IOPAD(0x014c, PIN_OUTPUT, 4) /* (AA14) PRG1_PRU1_GPO17.RGMII1_TD3 */
- AM64X_IOPAD(0x00e0, PIN_OUTPUT, 4) /* (U14) PRG1_PRU0_GPO10.RGMII1_TXC */
- AM64X_IOPAD(0x00dc, PIN_OUTPUT, 4) /* (U15) PRG1_PRU0_GPO9.RGMII1_TX_CTL */
- >;
- };
-
- rgmii2_pins_default: rgmii2-pins-default {
- pinctrl-single,pins = <
- AM64X_IOPAD(0x0108, PIN_INPUT, 4) /* (W11) PRG1_PRU1_GPO0.RGMII2_RD0 */
- AM64X_IOPAD(0x010c, PIN_INPUT, 4) /* (V11) PRG1_PRU1_GPO1.RGMII2_RD1 */
- AM64X_IOPAD(0x0110, PIN_INPUT, 4) /* (AA12) PRG1_PRU1_GPO2.RGMII2_RD2 */
- AM64X_IOPAD(0x0114, PIN_INPUT, 4) /* (Y12) PRG1_PRU1_GPO3.RGMII2_RD3 */
- AM64X_IOPAD(0x0120, PIN_INPUT, 4) /* (U11) PRG1_PRU1_GPO6.RGMII2_RXC */
- AM64X_IOPAD(0x0118, PIN_INPUT, 4) /* (W12) PRG1_PRU1_GPO4.RGMII2_RX_CTL */
- AM64X_IOPAD(0x0134, PIN_OUTPUT, 4) /* (AA10) PRG1_PRU1_GPO11.RGMII2_TD0 */
- AM64X_IOPAD(0x0138, PIN_OUTPUT, 4) /* (V10) PRG1_PRU1_GPO12.RGMII2_TD1 */
- AM64X_IOPAD(0x013c, PIN_OUTPUT, 4) /* (U10) PRG1_PRU1_GPO13.RGMII2_TD2 */
- AM64X_IOPAD(0x0140, PIN_OUTPUT, 4) /* (AA11) PRG1_PRU1_GPO14.RGMII2_TD3 */
- AM64X_IOPAD(0x0148, PIN_OUTPUT, 4) /* (Y10) PRG1_PRU1_GPO16.RGMII2_TXC */
- AM64X_IOPAD(0x0144, PIN_OUTPUT, 4) /* (Y11) PRG1_PRU1_GPO15.RGMII2_TX_CTL */
- >;
- };
};
&dmsc {
@@ -189,79 +66,36 @@
ti,secure-host;
};
-&main_uart0 {
- /delete-property/ power-domains;
- /delete-property/ clocks;
- /delete-property/ clock-names;
- pinctrl-names = "default";
- pinctrl-0 = <&main_uart0_pins_default>;
- status = "okay";
-};
-
-&main_uart1 {
- bootph-pre-ram;
- pinctrl-names = "default";
- pinctrl-0 = <&main_uart1_pins_default>;
-};
-
&sdhci1 {
- /delete-property/ power-domains;
clocks = <&clk_200mhz>;
clock-names = "clk_xin";
- ti,driver-strength-ohm = <50>;
- disable-wp;
- pinctrl-0 = <&main_mmc1_pins_default>;
};
-&serdes_ln_ctrl {
- idle-states = <AM64_SERDES0_LANE0_USB>;
-};
-
&serdes_wiz0 {
status = "okay";
};
-&serdes0 {
- serdes0_usb_link: link@0 {
- reg = <0>;
- cdns,num-lanes = <1>;
- #phy-cells = <0>;
- cdns,phy-type = <PHY_TYPE_USB3>;
- resets = <&serdes_wiz0 1>;
- };
-};
-
-&usbss0 {
- ti,vbus-divider;
-};
-
-&usb0 {
- dr_mode = "host";
- maximum-speed = "super-speed";
- pinctrl-names = "default";
- pinctrl-0 = <&main_usb0_pins_default>;
- phys = <&serdes0_usb_link>;
- phy-names = "cdns3,usb3-phy";
-};
-
-&cpsw3g {
- pinctrl-names = "default";
- pinctrl-0 = <&mdio1_pins_default
- &rgmii1_pins_default
- &rgmii2_pins_default>;
-};
-
-&cpsw_port2 {
- phy-mode = "rgmii-rxid";
- phy-handle = <&cpsw3g_phy1>;
+/* UART is initialized before SYSFW is started
+ * so we can't do any power-domain/clock operations.
+ * Delete clock/power-domain properties to avoid
+ * UART init failure
+ */
+&main_uart0 {
+ /delete-property/ power-domains;
+ /delete-property/ clocks;
+ /delete-property/ clock-names;
};
-&cpsw3g_mdio {
- cpsw3g_phy1: ethernet-phy@1 {
- reg = <1>;
- ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
- ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
- };
+/* timer init is called as part of rproc_start() while
+ * starting System Firmware, so any clock/power-domain
+ * operations will fail as SYSFW is not yet up and running.
+ * Delete all clock/power-domain properties to avoid
+ * timer init failure.
+ * This is an always on timer at 20MHz.
+ */
+&main_timer0 {
+ /delete-property/ clocks;
+ /delete-property/ assigned-clocks;
+ /delete-property/ assigned-clock-parents;
+ /delete-property/ power-domains;
};
-
-#include "k3-am642-sk-u-boot.dtsi"