mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL
Cleanup this driver to use dt in U-boot and static platdata in SPL.
This requires the following steps:
1. Move all platdata assignment from probe() to ofdata_to_platdata().
This function is only called in U-boot.
2. Replicate all the platdata assignment being done in
ofdata_to_platdata() in the omapl138 board file. This data is used in
the SPL case where SPL_OF_CONTROL is not enabled.
3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig
This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
diff --git a/drivers/mmc/davinci_mmc.c b/drivers/mmc/davinci_mmc.c
index 2408a68..4ef9f7c 100644
--- a/drivers/mmc/davinci_mmc.c
+++ b/drivers/mmc/davinci_mmc.c
@@ -18,7 +18,6 @@
#include <asm-generic/gpio.h>
#include <linux/delay.h>
-#define DAVINCI_MAX_BLOCKS (32)
#define WATCHDOG_COUNT (100000)
#define get_val(addr) REG(addr)
@@ -34,12 +33,6 @@
struct gpio_desc cd_gpio; /* Card Detect GPIO */
struct gpio_desc wp_gpio; /* Write Protect GPIO */
};
-
-struct davinci_mmc_plat
-{
- struct mmc_config cfg;
- struct mmc mmc;
-};
#endif
/* Set davinci clock prescalar value based on the required clock in HZ */
@@ -487,43 +480,16 @@
struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
struct davinci_mmc_plat *plat = dev_get_platdata(dev);
struct davinci_mmc_priv *priv = dev_get_priv(dev);
- struct mmc_config *cfg = &plat->cfg;
-#ifdef CONFIG_SPL_BUILD
- int ret;
-#endif
-
- cfg->f_min = 200000;
- cfg->f_max = 25000000;
- cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
- cfg->host_caps = MMC_MODE_4BIT, /* DA850 supports only 4-bit SD/MMC */
- cfg->b_max = DAVINCI_MAX_BLOCKS;
- cfg->name = "da830-mmc";
- priv->reg_base = (struct davinci_mmc_regs *)dev_read_addr(dev);
+ priv->reg_base = plat->reg_base;
priv->input_clk = clk_get(DAVINCI_MMCSD_CLKID);
-
#if CONFIG_IS_ENABLED(DM_GPIO)
/* These GPIOs are optional */
gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio, GPIOD_IS_IN);
gpio_request_by_name(dev, "wp-gpios", 0, &priv->wp_gpio, GPIOD_IS_IN);
#endif
-
upriv->mmc = &plat->mmc;
-#ifdef CONFIG_SPL_BUILD
- /*
- * FIXME This is a temporary workaround to enable the driver model in
- * SPL on omapl138-lcdk. For some reason the bind() callback is not
- * being called in SPL for MMC which breaks the mmc boot - the hack
- * is to call mmc_bind() from probe(). We also don't have full DT
- * support in SPL, hence the hard-coded base register address.
- */
- priv->reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE;
- ret = mmc_bind(dev, &plat->mmc, &plat->cfg);
- if (ret)
- return ret;
-#endif
-
return davinci_dm_mmc_init(dev);
}
@@ -534,21 +500,44 @@
return mmc_bind(dev, &plat->mmc, &plat->cfg);
}
+#if CONFIG_IS_ENABLED(OF_CONTROL)
+static int davinci_mmc_ofdata_to_platdata(struct udevice *dev)
+{
+ struct davinci_mmc_plat *plat = dev_get_platdata(dev);
+ struct mmc_config *cfg = &plat->cfg;
+
+ plat->reg_base = (struct davinci_mmc_regs *)dev_read_addr(dev);
+ cfg->f_min = 200000;
+ cfg->f_max = 25000000;
+ cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
+ cfg->host_caps = MMC_MODE_4BIT, /* DA850 supports only 4-bit SD/MMC */
+ cfg->b_max = DAVINCI_MAX_BLOCKS;
+ cfg->name = "da830-mmc";
+
+ return 0;
+}
+
static const struct udevice_id davinci_mmc_ids[] = {
{ .compatible = "ti,da830-mmc" },
{},
};
-
+#endif
U_BOOT_DRIVER(davinci_mmc_drv) = {
.name = "davinci_mmc",
.id = UCLASS_MMC,
+#if CONFIG_IS_ENABLED(OF_CONTROL)
.of_match = davinci_mmc_ids,
+ .platdata_auto_alloc_size = sizeof(struct davinci_mmc_plat),
+ .ofdata_to_platdata = davinci_mmc_ofdata_to_platdata,
+#endif
#if CONFIG_BLK
.bind = davinci_mmc_bind,
#endif
.probe = davinci_mmc_probe,
.ops = &davinci_mmc_ops,
- .platdata_auto_alloc_size = sizeof(struct davinci_mmc_plat),
.priv_auto_alloc_size = sizeof(struct davinci_mmc_priv),
+#if !CONFIG_IS_ENABLED(OF_CONTROL)
+ .flags = DM_FLAG_PRE_RELOC,
+#endif
};
#endif