esd config files updated
diff --git a/include/configs/CPCI405.h b/include/configs/CPCI405.h
index 7c600d9..b159182 100644
--- a/include/configs/CPCI405.h
+++ b/include/configs/CPCI405.h
@@ -44,30 +44,17 @@
#define CONFIG_BAUDRATE 9600
#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-#if 0
-#define CONFIG_PREBOOT \
- "crc32 f0207004 ffc 0;" \
- "if cmp 0 f0207000 1;" \
- "then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;" \
- "else;echo Old CRC is bad;fi"
-#endif
-
#undef CONFIG_BOOTARGS
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000 ffca0000"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm ffc00000"
-#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
+#undef CONFIG_BOOTCOMMAND
+
+#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \
CONFIG_BOOTP_DNS | \
@@ -79,6 +66,7 @@
CFG_CMD_PCI | \
CFG_CMD_IRQ | \
CFG_CMD_IDE | \
+ CFG_CMD_FAT | \
CFG_CMD_ELF | \
CFG_CMD_MII | \
CFG_CMD_EEPROM )
@@ -86,6 +74,8 @@
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
@@ -134,35 +124,39 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
-#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
-#define PCI_HOST_FORCE 1 /* configure as pci host */
-#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
+#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
+#define PCI_HOST_FORCE 1 /* configure as pci host */
+#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
-#define CONFIG_PCI /* include pci support */
-#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
- /* resource configuration */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+ /* resource configuration */
-#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
+#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
-#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
-#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
-#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
-#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
-#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
-#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
-#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
+#define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
+#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
+#define CFG_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */
+#define CFG_PCI_PTM1MS 0xfc000001 /* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
+#define CFG_PCI_PTM2LA 0xffc00000 /* point to flash */
+#define CFG_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
+#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* IDE/ATA stuff
@@ -221,23 +215,24 @@
#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
+#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */
+#define CFG_VXWORKS_MAC_PTR (CFG_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/
+
#if 1 /* Use NVRAM for environment variables */
/*-----------------------------------------------------------------------
* NVRAM organization
*/
#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
-#define CFG_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
-#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */
#define CFG_ENV_SIZE 0x1000 /* Size of Environment vars */
#define CFG_ENV_ADDR \
(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CFG_ENV_SIZE) /* Env */
-#define CFG_NVRAM_VXWORKS_OFFS 0x6900 /* Offset for VxWorks eth-addr */
#else /* Use EEPROM for environment variables */
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x200 /* 512 bytes may be used for env vars */
+#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars */
/* total size of a CAT24WC08 is 1024 bytes */
#endif