mpc83xx: Migrate BATS config to Kconfig
The BATs (block address translation registers) determine the initial
memory window mappings. Hence, they must be known at compile time and
cannot be implemented in the DT mechanism.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
diff --git a/configs/kmeter1_defconfig b/configs/kmeter1_defconfig
index 600a1ad..10f7fdf 100644
--- a/configs/kmeter1_defconfig
+++ b/configs/kmeter1_defconfig
@@ -2,6 +2,7 @@
CONFIG_SYS_TEXT_BASE=0xF0000000
CONFIG_SYS_CLK_FREQ=66000000
CONFIG_MPC83xx=y
+CONFIG_HIGH_BATS=y
CONFIG_TARGET_KMETER1=y
CONFIG_DDR_MC_CLOCK_MODE_1_1=y
CONFIG_SYSTEM_PLL_VCO_DIV_4=y
@@ -12,6 +13,58 @@
CONFIG_BOOT_ROM_INTERFACE_GPCM_16BIT=y
CONFIG_LALE_TIMING_EARLIER=y
CONFIG_LDP_PIN_MUX_STATE_0=y
+CONFIG_BAT0=y
+CONFIG_BAT0_NAME="SDRAM"
+CONFIG_BAT0_BASE=0x00000000
+CONFIG_BAT0_LENGTH_256_MBYTES=y
+CONFIG_BAT0_ACCESS_RW=y
+CONFIG_BAT0_ICACHE_INHIBITED=y
+CONFIG_BAT0_ICACHE_GUARDED=y
+CONFIG_BAT0_DCACHE_INHIBITED=y
+CONFIG_BAT0_DCACHE_GUARDED=y
+CONFIG_BAT0_USER_MODE_VALID=y
+CONFIG_BAT0_SUPERVISOR_MODE_VALID=y
+CONFIG_BAT1=y
+CONFIG_BAT1_NAME="IMMR"
+CONFIG_BAT1_BASE=0xE0000000
+CONFIG_BAT1_LENGTH_4_MBYTES=y
+CONFIG_BAT1_ACCESS_RW=y
+CONFIG_BAT1_ICACHE_INHIBITED=y
+CONFIG_BAT1_ICACHE_GUARDED=y
+CONFIG_BAT1_DCACHE_INHIBITED=y
+CONFIG_BAT1_DCACHE_GUARDED=y
+CONFIG_BAT1_USER_MODE_VALID=y
+CONFIG_BAT1_SUPERVISOR_MODE_VALID=y
+CONFIG_BAT2=y
+CONFIG_BAT2_NAME="KMBEC_FPGA"
+CONFIG_BAT2_BASE=0xE8000000
+CONFIG_BAT2_LENGTH_128_MBYTES=y
+CONFIG_BAT2_ACCESS_RW=y
+CONFIG_BAT2_ICACHE_MEMORYCOHERENCE=y
+CONFIG_BAT2_DCACHE_INHIBITED=y
+CONFIG_BAT2_DCACHE_GUARDED=y
+CONFIG_BAT2_USER_MODE_VALID=y
+CONFIG_BAT2_SUPERVISOR_MODE_VALID=y
+CONFIG_BAT3=y
+CONFIG_BAT3_NAME="FLASH"
+CONFIG_BAT3_BASE=0xF0000000
+CONFIG_BAT3_LENGTH_256_MBYTES=y
+CONFIG_BAT3_ACCESS_RW=y
+CONFIG_BAT3_ICACHE_MEMORYCOHERENCE=y
+CONFIG_BAT3_DCACHE_INHIBITED=y
+CONFIG_BAT3_DCACHE_GUARDED=y
+CONFIG_BAT3_USER_MODE_VALID=y
+CONFIG_BAT3_SUPERVISOR_MODE_VALID=y
+CONFIG_BAT5=y
+CONFIG_BAT5_NAME="PAXE"
+CONFIG_BAT5_BASE=0xA0000000
+CONFIG_BAT5_LENGTH_256_MBYTES=y
+CONFIG_BAT5_ACCESS_RW=y
+CONFIG_BAT5_ICACHE_MEMORYCOHERENCE=y
+CONFIG_BAT5_DCACHE_INHIBITED=y
+CONFIG_BAT5_DCACHE_GUARDED=y
+CONFIG_BAT5_USER_MODE_VALID=y
+CONFIG_BAT5_SUPERVISOR_MODE_VALID=y
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_STDOUT_VIA_ALIAS=y
CONFIG_MISC_INIT_R=y