ARM: imx: Auto-detect PHY on Data Modul i.MX8M Mini/Plus eDM SBC
Implement fdtdec_board_setup() auto-detection of ethernet PHY.
This uses properties of the hardware and pull resistor placement.
If GPIO1_16 RGMII_MDC is HIGH, then R530 (MX8MM eDM SBC) or
R390 (MX8MP eDM SBC) is populated. R530 or R390 is populated
only on boards with AR8031 PHY.
If GPIO1_16 RGMII_MDC is LOW, then the in-SoM pull down is the
dominant pull resistor. This is the case on boards with BCM54213PE
PHY.
In case AR8031 PHY is populated, the PHY MDIO address is 0, in
case BCM54213PE PHY is populated, the PHY MDIO address is 1, the
fdtdec_board_setup() is used to patch the correct address into
the U-Boot control DT.
Enable broadcom PHY support to support both PHYs.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
diff --git a/arch/arm/dts/imx8mp-data-modul-edm-sbc-u-boot.dtsi b/arch/arm/dts/imx8mp-data-modul-edm-sbc-u-boot.dtsi
index a2b5976..cb6ea35 100644
--- a/arch/arm/dts/imx8mp-data-modul-edm-sbc-u-boot.dtsi
+++ b/arch/arm/dts/imx8mp-data-modul-edm-sbc-u-boot.dtsi
@@ -51,12 +51,6 @@
};
};
-&eqos {
- /delete-property/ assigned-clocks;
- /delete-property/ assigned-clock-parents;
- /delete-property/ assigned-clock-rates;
-};
-
&gpio1 {
bootph-pre-ram;
};
diff --git a/board/data_modul/imx8mm_edm_sbc/imx8mm_data_modul_edm_sbc.c b/board/data_modul/imx8mm_edm_sbc/imx8mm_data_modul_edm_sbc.c
index ff89333..bfb2bdd 100644
--- a/board/data_modul/imx8mm_edm_sbc/imx8mm_data_modul_edm_sbc.c
+++ b/board/data_modul/imx8mm_edm_sbc/imx8mm_data_modul_edm_sbc.c
@@ -5,9 +5,11 @@
#include <common.h>
#include <asm/arch/clock.h>
+#include <asm/arch/imx8mm_pins.h>
#include <asm/io.h>
#include <dm.h>
#include <dm/device-internal.h>
+#include <linux/bitfield.h>
#include <malloc.h>
#include <spl.h>
@@ -34,3 +36,43 @@
return 0;
}
+
+int fdtdec_board_setup(const void *fdt_blob)
+{
+ const void __iomem *mux = (void __iomem *)IOMUXC_BASE_ADDR +
+ FIELD_GET(MUX_CTRL_OFS_MASK, IMX8MM_PAD_ENET_MDC_GPIO1_IO16);
+ const char *phy_compat = "ethernet-phy-ieee802.3-c22";
+ bool is_bcmphy;
+ int phy_node;
+ int ret;
+
+ /* Do nothing if not i.MX8MM eDM SBC */
+ ret = fdt_node_check_compatible(fdt_blob, 0, "dmo,imx8mm-data-modul-edm-sbc");
+ if (ret)
+ return 0;
+
+ /*
+ * If GPIO1_16 RGMII_MDC is HIGH, then R530 is populated.
+ * R530 is populated only on boards with AR8031 PHY.
+ *
+ * If GPIO1_16 RGMII_MDC is LOW, then the in-SoM pull down
+ * is the dominant pull resistor. This is the case on boards
+ * with BCM54213PE PHY.
+ */
+ setbits_le32(mux, IOMUX_CONFIG_SION);
+ is_bcmphy = !(readl(GPIO1_BASE_ADDR) & BIT(16));
+ clrbits_le32(mux, IOMUX_CONFIG_SION);
+
+ phy_node = fdt_node_offset_by_compatible(fdt_blob, -1, phy_compat);
+ if (phy_node < 0)
+ return 0;
+
+ /*
+ * Update PHY MDC address in control DT based on the populated
+ * PHY type. AR8031 is at address 0, BCM54213PE is at address 1.
+ */
+ fdt_setprop_inplace_u32((void *)fdt_blob, phy_node,
+ "reg", is_bcmphy ? 1 : 0);
+
+ return 0;
+}
diff --git a/board/data_modul/imx8mp_edm_sbc/imx8mp_data_modul_edm_sbc.c b/board/data_modul/imx8mp_edm_sbc/imx8mp_data_modul_edm_sbc.c
index 9fbbbc1..f0f373a 100644
--- a/board/data_modul/imx8mp_edm_sbc/imx8mp_data_modul_edm_sbc.c
+++ b/board/data_modul/imx8mp_edm_sbc/imx8mp_data_modul_edm_sbc.c
@@ -5,11 +5,13 @@
#include <common.h>
#include <asm/arch/clock.h>
+#include <asm/arch/imx8mp_pins.h>
#include <asm/io.h>
#include <dm.h>
#include <dm/device-internal.h>
#include <env.h>
#include <env_internal.h>
+#include <linux/bitfield.h>
#include <malloc.h>
#include <net.h>
#include <spl.h>
@@ -65,3 +67,51 @@
return 0;
}
+
+int fdtdec_board_setup(const void *fdt_blob)
+{
+ const void __iomem *mux = (void __iomem *)IOMUXC_BASE_ADDR +
+ FIELD_GET(MUX_CTRL_OFS_MASK, MX8MP_PAD_ENET_MDC__ENET_QOS_MDC);
+ const char *phy_compat = "ethernet-phy-ieee802.3-c22";
+ bool is_bcmphy;
+ int phy_node;
+ int ret;
+
+ /* Do nothing if not i.MX8MP eDM SBC */
+ ret = fdt_node_check_compatible(fdt_blob, 0, "dmo,imx8mp-data-modul-edm-sbc");
+ if (ret)
+ return 0;
+
+ /*
+ * If GPIO1_16 RGMII_MDC is HIGH, then R390 is populated.
+ * R390 is populated only on boards with AR8031 PHY.
+ *
+ * If GPIO1_16 RGMII_MDC is LOW, then the in-SoM pull down
+ * is the dominant pull resistor. This is the case on boards
+ * with BCM54213PE PHY.
+ */
+ setbits_le32(mux, IOMUX_CONFIG_SION);
+ is_bcmphy = !(readl(GPIO1_BASE_ADDR) & BIT(16));
+ clrbits_le32(mux, IOMUX_CONFIG_SION);
+
+ phy_node = fdt_node_offset_by_compatible(fdt_blob, -1, phy_compat);
+ if (phy_node < 0)
+ return 0;
+
+ /*
+ * Update PHY MDC address in control DT based on the populated
+ * PHY type. AR8031 is at address 0, BCM54213PE is at address 1.
+ */
+ fdt_setprop_inplace_u32((void *)fdt_blob, phy_node,
+ "reg", is_bcmphy ? 1 : 0);
+
+ /* Apply the same modification to EQoS PHY */
+ phy_node = fdt_node_offset_by_compatible(fdt_blob, phy_node, phy_compat);
+ if (phy_node < 0)
+ return 0;
+
+ fdt_setprop_inplace_u32((void *)fdt_blob, phy_node,
+ "reg", is_bcmphy ? 1 : 0);
+
+ return 0;
+}
diff --git a/configs/imx8mm_data_modul_edm_sbc_defconfig b/configs/imx8mm_data_modul_edm_sbc_defconfig
index b16800d..7e9c48e 100644
--- a/configs/imx8mm_data_modul_edm_sbc_defconfig
+++ b/configs/imx8mm_data_modul_edm_sbc_defconfig
@@ -195,6 +195,7 @@
CONFIG_SPI_FLASH_MTD=y
CONFIG_PHYLIB=y
CONFIG_PHY_ATHEROS=y
+CONFIG_PHY_BROADCOM=y
CONFIG_DM_MDIO=y
CONFIG_DM_ETH_PHY=y
CONFIG_FEC_MXC=y
diff --git a/configs/imx8mp_data_modul_edm_sbc_defconfig b/configs/imx8mp_data_modul_edm_sbc_defconfig
index b6a3730..ba4730a 100644
--- a/configs/imx8mp_data_modul_edm_sbc_defconfig
+++ b/configs/imx8mp_data_modul_edm_sbc_defconfig
@@ -207,6 +207,7 @@
CONFIG_SPI_FLASH_WINBOND=y
CONFIG_SPI_FLASH_MTD=y
CONFIG_PHY_ATHEROS=y
+CONFIG_PHY_BROADCOM=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
CONFIG_DM_MDIO=y