arm64: a37xx: pci: add support for aardvark pcie driver
This patch introduced the Aardvark PCIe driver based
driver model.
The PCIe driver is supposed to work in Root Complex
mode. It only supports X1 lane width.
Signed-off-by: Wilson Ding <dingwei@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/38725
Reviewed-by: Victor Gu <xigu@marvell.com>
Reviewed-by: Hua Jing <jinghua@marvell.com>
Tested-by: Hua Jing <jinghua@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/drivers/pci/Kconfig b/drivers/pci/Kconfig
index da6421f..c20a0cc 100644
--- a/drivers/pci/Kconfig
+++ b/drivers/pci/Kconfig
@@ -26,6 +26,16 @@
measure when porting a board to use driver model for PCI. Once the
board is fully supported, this option should be disabled.
+config PCI_AARDVARK
+ bool "Enable Aardvark PCIe driver"
+ default n
+ depends on DM_PCI
+ depends on ARMADA_3700
+ help
+ Say Y here if you want to enable PCIe controller support on
+ Armada37x0 SoCs. The PCIe controller on Armada37x0 is based on
+ Aardvark hardware.
+
config PCI_PNP
bool "Enable Plug & Play support for PCI"
depends on PCI || DM_PCI
diff --git a/drivers/pci/Makefile b/drivers/pci/Makefile
index 8fbab46..40ebc06 100644
--- a/drivers/pci/Makefile
+++ b/drivers/pci/Makefile
@@ -30,6 +30,7 @@
obj-$(CONFIG_SH7751_PCI) +=pci_sh7751.o
obj-$(CONFIG_SH7780_PCI) +=pci_sh7780.o
obj-$(CONFIG_PCI_TEGRA) += pci_tegra.o
+obj-$(CONFIG_PCI_AARDVARK) += pci-aardvark.o
obj-$(CONFIG_PCIE_DW_MVEBU) += pcie_dw_mvebu.o
obj-$(CONFIG_PCIE_LAYERSCAPE) += pcie_layerscape.o
obj-$(CONFIG_PCIE_LAYERSCAPE) += pcie_layerscape_fixup.o
diff --git a/drivers/pci/pci-aardvark.c b/drivers/pci/pci-aardvark.c
new file mode 100644
index 0000000..69a4d81
--- /dev/null
+++ b/drivers/pci/pci-aardvark.c
@@ -0,0 +1,690 @@
+/*
+ * ***************************************************************************
+ * Copyright (C) 2015 Marvell International Ltd.
+ * ***************************************************************************
+ * This program is free software: you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the Free
+ * Software Foundation, either version 2 of the License, or any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ * ***************************************************************************
+ */
+/* pcie_advk.c
+ *
+ * Ported from Linux driver - driver/pci/host/pci-aardvark.c
+ *
+ * Author: Victor Gu <xigu@marvell.com>
+ * Hezi Shahmoon <hezi.shahmoon@marvell.com>
+ *
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <pci.h>
+#include <asm/io.h>
+#include <asm-generic/gpio.h>
+#include <linux/ioport.h>
+
+/* PCIe core registers */
+#define PCIE_CORE_CMD_STATUS_REG 0x4
+#define PCIE_CORE_CMD_IO_ACCESS_EN BIT(0)
+#define PCIE_CORE_CMD_MEM_ACCESS_EN BIT(1)
+#define PCIE_CORE_CMD_MEM_IO_REQ_EN BIT(2)
+#define PCIE_CORE_DEV_CTRL_STATS_REG 0xc8
+#define PCIE_CORE_DEV_CTRL_STATS_RELAX_ORDER_DISABLE (0 << 4)
+#define PCIE_CORE_DEV_CTRL_STATS_SNOOP_DISABLE (0 << 11)
+#define PCIE_CORE_LINK_CTRL_STAT_REG 0xd0
+#define PCIE_CORE_LINK_TRAINING BIT(5)
+#define PCIE_CORE_ERR_CAPCTL_REG 0x118
+#define PCIE_CORE_ERR_CAPCTL_ECRC_CHK_TX BIT(5)
+#define PCIE_CORE_ERR_CAPCTL_ECRC_CHK_TX_EN BIT(6)
+#define PCIE_CORE_ERR_CAPCTL_ECRC_CHECK BIT(7)
+#define PCIE_CORE_ERR_CAPCTL_ECRC_CHECK_RCV BIT(8)
+
+/* PIO registers base address and register offsets */
+#define PIO_BASE_ADDR 0x4000
+#define PIO_CTRL (PIO_BASE_ADDR + 0x0)
+#define PIO_CTRL_TYPE_MASK GENMASK(3, 0)
+#define PIO_CTRL_ADDR_WIN_DISABLE BIT(24)
+#define PIO_STAT (PIO_BASE_ADDR + 0x4)
+#define PIO_COMPLETION_STATUS_SHIFT 7
+#define PIO_COMPLETION_STATUS_MASK GENMASK(9, 7)
+#define PIO_COMPLETION_STATUS_OK 0
+#define PIO_COMPLETION_STATUS_UR 1
+#define PIO_COMPLETION_STATUS_CRS 2
+#define PIO_COMPLETION_STATUS_CA 4
+#define PIO_NON_POSTED_REQ BIT(10)
+#define PIO_ERR_STATUS BIT(11)
+#define PIO_ADDR_LS (PIO_BASE_ADDR + 0x8)
+#define PIO_ADDR_MS (PIO_BASE_ADDR + 0xc)
+#define PIO_WR_DATA (PIO_BASE_ADDR + 0x10)
+#define PIO_WR_DATA_STRB (PIO_BASE_ADDR + 0x14)
+#define PIO_RD_DATA (PIO_BASE_ADDR + 0x18)
+#define PIO_START (PIO_BASE_ADDR + 0x1c)
+#define PIO_ISR (PIO_BASE_ADDR + 0x20)
+
+/* Aardvark Control registers */
+#define CONTROL_BASE_ADDR 0x4800
+#define PCIE_CORE_CTRL0_REG (CONTROL_BASE_ADDR + 0x0)
+#define PCIE_GEN_SEL_MSK 0x3
+#define PCIE_GEN_SEL_SHIFT 0x0
+#define SPEED_GEN_1 0
+#define SPEED_GEN_2 1
+#define SPEED_GEN_3 2
+#define IS_RC_MSK 1
+#define IS_RC_SHIFT 2
+#define LANE_CNT_MSK 0x18
+#define LANE_CNT_SHIFT 0x3
+#define LANE_COUNT_1 (0 << LANE_CNT_SHIFT)
+#define LANE_COUNT_2 (1 << LANE_CNT_SHIFT)
+#define LANE_COUNT_4 (2 << LANE_CNT_SHIFT)
+#define LANE_COUNT_8 (3 << LANE_CNT_SHIFT)
+#define LINK_TRAINING_EN BIT(6)
+#define PCIE_CORE_CTRL2_REG (CONTROL_BASE_ADDR + 0x8)
+#define PCIE_CORE_CTRL2_RESERVED 0x7
+#define PCIE_CORE_CTRL2_TD_ENABLE BIT(4)
+#define PCIE_CORE_CTRL2_STRICT_ORDER_ENABLE BIT(5)
+#define PCIE_CORE_CTRL2_ADDRWIN_MAP_ENABLE BIT(6)
+
+/* LMI registers base address and register offsets */
+#define LMI_BASE_ADDR 0x6000
+#define CFG_REG (LMI_BASE_ADDR + 0x0)
+#define LTSSM_SHIFT 24
+#define LTSSM_MASK 0x3f
+#define LTSSM_L0 0x10
+
+/* PCIe core controller registers */
+#define CTRL_CORE_BASE_ADDR 0x18000
+#define CTRL_CONFIG_REG (CTRL_CORE_BASE_ADDR + 0x0)
+#define CTRL_MODE_SHIFT 0x0
+#define CTRL_MODE_MASK 0x1
+#define PCIE_CORE_MODE_DIRECT 0x0
+#define PCIE_CORE_MODE_COMMAND 0x1
+
+/* Transaction types */
+#define PCIE_CONFIG_RD_TYPE0 0x8
+#define PCIE_CONFIG_RD_TYPE1 0x9
+#define PCIE_CONFIG_WR_TYPE0 0xa
+#define PCIE_CONFIG_WR_TYPE1 0xb
+
+/* PCI_BDF shifts 8bit, so we need extra 4bit shift */
+#define PCIE_BDF(dev) (dev << 4)
+#define PCIE_CONF_BUS(bus) (((bus) & 0xff) << 20)
+#define PCIE_CONF_DEV(dev) (((dev) & 0x1f) << 15)
+#define PCIE_CONF_FUNC(fun) (((fun) & 0x7) << 12)
+#define PCIE_CONF_REG(reg) ((reg) & 0xffc)
+#define PCIE_CONF_ADDR(bus, devfn, where) \
+ (PCIE_CONF_BUS(bus) | PCIE_CONF_DEV(PCI_SLOT(devfn)) | \
+ PCIE_CONF_FUNC(PCI_FUNC(devfn)) | PCIE_CONF_REG(where))
+
+/* PCIe Retries & Timeout definitions */
+#define MAX_RETRIES 10
+#define PIO_WAIT_TIMEOUT 100
+#define LINK_WAIT_TIMEOUT 100000
+
+#define CFG_RD_UR_VAL 0xFFFFFFFF
+#define CFG_RD_CRS_VAL 0xFFFF0001
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/**
+ * struct pcie_advk - Advk PCIe controller state
+ *
+ * @reg_base: The base address of the register space.
+ * @first_busno: This driver supports multiple PCIe controllers.
+ * first_busno stores the bus number of the PCIe root-port
+ * number which may vary depending on the PCIe setup
+ * (PEX switches etc).
+ * @device: The pointer to PCI uclass device.
+ */
+struct pcie_advk {
+ void *base;
+ int first_busno;
+ struct udevice *dev;
+};
+
+static inline void advk_writel(struct pcie_advk *pcie, uint val, uint reg)
+{
+ writel(val, pcie->base + reg);
+}
+
+static inline uint advk_readl(struct pcie_advk *pcie, uint reg)
+{
+ return readl(pcie->base + reg);
+}
+
+/**
+ * pcie_advk_addr_valid() - Check for valid bus address
+ *
+ * @bdf: The PCI device to access
+ * @first_busno: Bus number of the PCIe controller root complex
+ *
+ * Return: 1 on valid, 0 on invalid
+ */
+static int pcie_advk_addr_valid(pci_dev_t bdf, int first_busno)
+{
+ /*
+ * In PCIE-E only a single device (0) can exist
+ * on the local bus. Beyound the local bus, there might be
+ * a Switch and everything is possible.
+ */
+ if ((PCI_BUS(bdf) == first_busno) && (PCI_DEV(bdf) > 0))
+ return 0;
+
+ return 1;
+}
+
+/**
+ * pcie_advk_wait_pio() - Wait for PIO access to be accomplished
+ *
+ * @pcie: The PCI device to access
+ *
+ * Wait up to 1 micro second for PIO access to be accomplished.
+ *
+ * Return 1 (true) if PIO access is accomplished.
+ * Return 0 (false) if PIO access is timed out.
+ */
+static int pcie_advk_wait_pio(struct pcie_advk *pcie)
+{
+ uint start, isr;
+ uint count;
+
+ for (count = 0; count < MAX_RETRIES; count++) {
+ start = advk_readl(pcie, PIO_START);
+ isr = advk_readl(pcie, PIO_ISR);
+ if (!start && isr)
+ return 1;
+ /*
+ * Do not check the PIO state too frequently,
+ * 100us delay is appropriate.
+ */
+ udelay(PIO_WAIT_TIMEOUT);
+ }
+
+ dev_err(pcie->dev, "config read/write timed out\n");
+ return 0;
+}
+
+/**
+ * pcie_advk_check_pio_status() - Validate PIO status and get the read result
+ *
+ * @pcie: Pointer to the PCI bus
+ * @read: Read from or write to configuration space - true(read) false(write)
+ * @read_val: Pointer to the read result, only valid when read is true
+ *
+ */
+static int pcie_advk_check_pio_status(struct pcie_advk *pcie,
+ bool read,
+ uint *read_val)
+{
+ uint reg;
+ unsigned int status;
+ char *strcomp_status, *str_posted;
+
+ reg = advk_readl(pcie, PIO_STAT);
+ status = (reg & PIO_COMPLETION_STATUS_MASK) >>
+ PIO_COMPLETION_STATUS_SHIFT;
+
+ switch (status) {
+ case PIO_COMPLETION_STATUS_OK:
+ if (reg & PIO_ERR_STATUS) {
+ strcomp_status = "COMP_ERR";
+ break;
+ }
+ /* Get the read result */
+ if (read)
+ *read_val = advk_readl(pcie, PIO_RD_DATA);
+ /* No error */
+ strcomp_status = NULL;
+ break;
+ case PIO_COMPLETION_STATUS_UR:
+ if (read) {
+ /* For reading, UR is not an error status. */
+ *read_val = CFG_RD_UR_VAL;
+ strcomp_status = NULL;
+ } else {
+ strcomp_status = "UR";
+ }
+ break;
+ case PIO_COMPLETION_STATUS_CRS:
+ if (read) {
+ /* For reading, CRS is not an error status. */
+ *read_val = CFG_RD_CRS_VAL;
+ strcomp_status = NULL;
+ } else {
+ strcomp_status = "CRS";
+ }
+ break;
+ case PIO_COMPLETION_STATUS_CA:
+ strcomp_status = "CA";
+ break;
+ default:
+ strcomp_status = "Unknown";
+ break;
+ }
+
+ if (!strcomp_status)
+ return 0;
+
+ if (reg & PIO_NON_POSTED_REQ)
+ str_posted = "Non-posted";
+ else
+ str_posted = "Posted";
+
+ dev_err(pcie->dev, "%s PIO Response Status: %s, %#x @ %#x\n",
+ str_posted, strcomp_status, reg,
+ advk_readl(pcie, PIO_ADDR_LS));
+
+ return -EFAULT;
+}
+
+/**
+ * pcie_advk_read_config() - Read from configuration space
+ *
+ * @bus: Pointer to the PCI bus
+ * @bdf: Identifies the PCIe device to access
+ * @offset: The offset into the device's configuration space
+ * @valuep: A pointer at which to store the read value
+ * @size: Indicates the size of access to perform
+ *
+ * Read a value of size @size from offset @offset within the configuration
+ * space of the device identified by the bus, device & function numbers in @bdf
+ * on the PCI bus @bus.
+ *
+ * Return: 0 on success
+ */
+static int pcie_advk_read_config(struct udevice *bus, pci_dev_t bdf,
+ uint offset, ulong *valuep,
+ enum pci_size_t size)
+{
+ struct pcie_advk *pcie = dev_get_priv(bus);
+ uint reg;
+ int ret;
+
+ dev_dbg(pcie->dev, "PCIE CFG read: (b,d,f)=(%2d,%2d,%2d) ",
+ PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
+
+ if (!pcie_advk_addr_valid(bdf, pcie->first_busno)) {
+ dev_dbg(pcie->dev, "- out of range\n");
+ *valuep = pci_get_ff(size);
+ return 0;
+ }
+
+ /* Start PIO */
+ advk_writel(pcie, 0, PIO_START);
+ advk_writel(pcie, 1, PIO_ISR);
+
+ /* Program the control register */
+ reg = advk_readl(pcie, PIO_CTRL);
+ reg &= ~PIO_CTRL_TYPE_MASK;
+ if (PCI_BUS(bdf) == pcie->first_busno)
+ reg |= PCIE_CONFIG_RD_TYPE0;
+ else
+ reg |= PCIE_CONFIG_RD_TYPE1;
+ advk_writel(pcie, reg, PIO_CTRL);
+
+ /* Program the address registers */
+ reg = PCIE_BDF(bdf) | PCIE_CONF_REG(offset);
+ advk_writel(pcie, reg, PIO_ADDR_LS);
+ advk_writel(pcie, 0, PIO_ADDR_MS);
+
+ /* Start the transfer */
+ advk_writel(pcie, 1, PIO_START);
+
+ if (!pcie_advk_wait_pio(pcie))
+ return -EINVAL;
+
+ /* Check PIO status and get the read result */
+ ret = pcie_advk_check_pio_status(pcie, true, ®);
+ if (ret)
+ return ret;
+
+ dev_dbg(pcie->dev, "(addr,size,val)=(0x%04x, %d, 0x%08x)\n",
+ offset, size, reg);
+ *valuep = pci_conv_32_to_size(reg, offset, size);
+
+ return 0;
+}
+
+/**
+ * pcie_calc_datastrobe() - Calculate data strobe
+ *
+ * @offset: The offset into the device's configuration space
+ * @size: Indicates the size of access to perform
+ *
+ * Calculate data strobe according to offset and size
+ *
+ */
+static uint pcie_calc_datastrobe(uint offset, enum pci_size_t size)
+{
+ uint bytes, data_strobe;
+
+ switch (size) {
+ case PCI_SIZE_8:
+ bytes = 1;
+ break;
+ case PCI_SIZE_16:
+ bytes = 2;
+ break;
+ default:
+ bytes = 4;
+ }
+
+ data_strobe = GENMASK(bytes - 1, 0) << (offset & 0x3);
+
+ return data_strobe;
+}
+
+/**
+ * pcie_advk_write_config() - Write to configuration space
+ *
+ * @bus: Pointer to the PCI bus
+ * @bdf: Identifies the PCIe device to access
+ * @offset: The offset into the device's configuration space
+ * @value: The value to write
+ * @size: Indicates the size of access to perform
+ *
+ * Write the value @value of size @size from offset @offset within the
+ * configuration space of the device identified by the bus, device & function
+ * numbers in @bdf on the PCI bus @bus.
+ *
+ * Return: 0 on success
+ */
+static int pcie_advk_write_config(struct udevice *bus, pci_dev_t bdf,
+ uint offset, ulong value,
+ enum pci_size_t size)
+{
+ struct pcie_advk *pcie = dev_get_priv(bus);
+ uint reg;
+
+ dev_dbg(pcie->dev, "PCIE CFG write: (b,d,f)=(%2d,%2d,%2d) ",
+ PCI_BUS(bdf), PCI_DEV(bdf), PCI_FUNC(bdf));
+ dev_dbg(pcie->dev, "(addr,size,val)=(0x%04x, %d, 0x%08lx)\n",
+ offset, size, value);
+
+ if (!pcie_advk_addr_valid(bdf, pcie->first_busno)) {
+ dev_dbg(pcie->dev, "- out of range\n");
+ return 0;
+ }
+
+ /* Start PIO */
+ advk_writel(pcie, 0, PIO_START);
+ advk_writel(pcie, 1, PIO_ISR);
+
+ /* Program the control register */
+ reg = advk_readl(pcie, PIO_CTRL);
+ reg &= ~PIO_CTRL_TYPE_MASK;
+ if (PCI_BUS(bdf) == pcie->first_busno)
+ reg |= PCIE_CONFIG_WR_TYPE0;
+ else
+ reg |= PCIE_CONFIG_WR_TYPE1;
+ advk_writel(pcie, reg, PIO_CTRL);
+
+ /* Program the address registers */
+ reg = PCIE_BDF(bdf) | PCIE_CONF_REG(offset);
+ advk_writel(pcie, reg, PIO_ADDR_LS);
+ advk_writel(pcie, 0, PIO_ADDR_MS);
+ dev_dbg(pcie->dev, "\tPIO req. - addr = 0x%08x\n", reg);
+
+ /* Program the data register */
+ reg = pci_conv_size_to_32(0, value, offset, size);
+ advk_writel(pcie, reg, PIO_WR_DATA);
+ dev_dbg(pcie->dev, "\tPIO req. - val = 0x%08x\n", reg);
+
+ /* Program the data strobe */
+ reg = pcie_calc_datastrobe(offset, size);
+ advk_writel(pcie, reg, PIO_WR_DATA_STRB);
+ dev_dbg(pcie->dev, "\tPIO req. - strb = 0x%02x\n", reg);
+
+ /* Start the transfer */
+ advk_writel(pcie, 1, PIO_START);
+
+ if (!pcie_advk_wait_pio(pcie)) {
+ dev_dbg(pcie->dev, "- wait pio timeout\n");
+ return -EINVAL;
+ }
+
+ /* Check PIO status */
+ pcie_advk_check_pio_status(pcie, false, ®);
+
+ return 0;
+}
+
+/**
+ * pcie_advk_link_up() - Check if PCIe link is up or not
+ *
+ * @pcie: The PCI device to access
+ *
+ * Return 1 (true) on link up.
+ * Return 0 (false) on link down.
+ */
+static int pcie_advk_link_up(struct pcie_advk *pcie)
+{
+ u32 val, ltssm_state;
+
+ val = advk_readl(pcie, CFG_REG);
+ ltssm_state = (val >> LTSSM_SHIFT) & LTSSM_MASK;
+ return ltssm_state >= LTSSM_L0;
+}
+
+/**
+ * pcie_advk_wait_for_link() - Wait for link training to be accomplished
+ *
+ * @pcie: The PCI device to access
+ *
+ * Wait up to 1 second for link training to be accomplished.
+ *
+ * Return 1 (true) if link training ends up with link up success.
+ * Return 0 (false) if link training ends up with link up failure.
+ */
+static int pcie_advk_wait_for_link(struct pcie_advk *pcie)
+{
+ int retries;
+
+ /* check if the link is up or not */
+ for (retries = 0; retries < MAX_RETRIES; retries++) {
+ if (pcie_advk_link_up(pcie)) {
+ printf("PCIE-%d: Link up\n", pcie->first_busno);
+ return 0;
+ }
+
+ udelay(LINK_WAIT_TIMEOUT);
+ }
+
+ printf("PCIE-%d: Link down\n", pcie->first_busno);
+
+ return -ETIMEDOUT;
+}
+
+/**
+ * pcie_advk_setup_hw() - PCIe initailzation
+ *
+ * @pcie: The PCI device to access
+ *
+ * Return: 0 on success
+ */
+static int pcie_advk_setup_hw(struct pcie_advk *pcie)
+{
+ u32 reg;
+
+ /* Set to Direct mode */
+ reg = advk_readl(pcie, CTRL_CONFIG_REG);
+ reg &= ~(CTRL_MODE_MASK << CTRL_MODE_SHIFT);
+ reg |= ((PCIE_CORE_MODE_DIRECT & CTRL_MODE_MASK) << CTRL_MODE_SHIFT);
+ advk_writel(pcie, reg, CTRL_CONFIG_REG);
+
+ /* Set PCI global control register to RC mode */
+ reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
+ reg |= (IS_RC_MSK << IS_RC_SHIFT);
+ advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
+
+ /* Set Advanced Error Capabilities and Control PF0 register */
+ reg = PCIE_CORE_ERR_CAPCTL_ECRC_CHK_TX |
+ PCIE_CORE_ERR_CAPCTL_ECRC_CHK_TX_EN |
+ PCIE_CORE_ERR_CAPCTL_ECRC_CHECK |
+ PCIE_CORE_ERR_CAPCTL_ECRC_CHECK_RCV;
+ advk_writel(pcie, reg, PCIE_CORE_ERR_CAPCTL_REG);
+
+ /* Set PCIe Device Control and Status 1 PF0 register */
+ reg = PCIE_CORE_DEV_CTRL_STATS_RELAX_ORDER_DISABLE |
+ PCIE_CORE_DEV_CTRL_STATS_SNOOP_DISABLE;
+ advk_writel(pcie, reg, PCIE_CORE_DEV_CTRL_STATS_REG);
+
+ /* Program PCIe Control 2 to disable strict ordering */
+ reg = PCIE_CORE_CTRL2_RESERVED |
+ PCIE_CORE_CTRL2_TD_ENABLE;
+ advk_writel(pcie, reg, PCIE_CORE_CTRL2_REG);
+
+ /* Set GEN2 */
+ reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
+ reg &= ~PCIE_GEN_SEL_MSK;
+ reg |= SPEED_GEN_2;
+ advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
+
+ /* Set lane X1 */
+ reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
+ reg &= ~LANE_CNT_MSK;
+ reg |= LANE_COUNT_1;
+ advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
+
+ /* Enable link training */
+ reg = advk_readl(pcie, PCIE_CORE_CTRL0_REG);
+ reg |= LINK_TRAINING_EN;
+ advk_writel(pcie, reg, PCIE_CORE_CTRL0_REG);
+
+ /*
+ * Enable AXI address window location generation:
+ * When it is enabled, the default outbound window
+ * configurations (Default User Field: 0xD0074CFC)
+ * are used to transparent address translation for
+ * the outbound transactions. Thus, PCIe address
+ * windows are not required.
+ */
+ reg = advk_readl(pcie, PCIE_CORE_CTRL2_REG);
+ reg |= PCIE_CORE_CTRL2_ADDRWIN_MAP_ENABLE;
+ advk_writel(pcie, reg, PCIE_CORE_CTRL2_REG);
+
+ /*
+ * Bypass the address window mapping for PIO:
+ * Since PIO access already contains all required
+ * info over AXI interface by PIO registers, the
+ * address window is not required.
+ */
+ reg = advk_readl(pcie, PIO_CTRL);
+ reg |= PIO_CTRL_ADDR_WIN_DISABLE;
+ advk_writel(pcie, reg, PIO_CTRL);
+
+ /* Start link training */
+ reg = advk_readl(pcie, PCIE_CORE_LINK_CTRL_STAT_REG);
+ reg |= PCIE_CORE_LINK_TRAINING;
+ advk_writel(pcie, reg, PCIE_CORE_LINK_CTRL_STAT_REG);
+
+ /* Wait for PCIe link up */
+ if (pcie_advk_wait_for_link(pcie))
+ return -ENXIO;
+
+ reg = advk_readl(pcie, PCIE_CORE_CMD_STATUS_REG);
+ reg |= PCIE_CORE_CMD_MEM_ACCESS_EN |
+ PCIE_CORE_CMD_IO_ACCESS_EN |
+ PCIE_CORE_CMD_MEM_IO_REQ_EN;
+ advk_writel(pcie, reg, PCIE_CORE_CMD_STATUS_REG);
+
+ return 0;
+}
+
+/**
+ * pcie_advk_probe() - Probe the PCIe bus for active link
+ *
+ * @dev: A pointer to the device being operated on
+ *
+ * Probe for an active link on the PCIe bus and configure the controller
+ * to enable this port.
+ *
+ * Return: 0 on success, else -ENODEV
+ */
+static int pcie_advk_probe(struct udevice *dev)
+{
+ struct pcie_advk *pcie = dev_get_priv(dev);
+
+#ifdef CONFIG_DM_GPIO
+ struct gpio_desc reset_gpio;
+
+ gpio_request_by_name(dev, "reset-gpio", 0, &reset_gpio,
+ GPIOD_IS_OUT);
+ /*
+ * Issue reset to add-in card through the dedicated GPIO.
+ * Some boards are connecting the card reset pin to common system
+ * reset wire and others are using separate GPIO port.
+ * In the last case we have to release a reset of the addon card
+ * using this GPIO.
+ *
+ * FIX-ME:
+ * The PCIe RESET signal is not supposed to be released along
+ * with the SOC RESET signal. It should be lowered as early as
+ * possible before PCIe PHY initialization. Moreover, the PCIe
+ * clock should be gated as well.
+ */
+ if (dm_gpio_is_valid(&reset_gpio)) {
+ dev_dbg(pcie->dev, "Toggle PCIE Reset GPIO ...\n");
+ dm_gpio_set_value(&reset_gpio, 0);
+ mdelay(200);
+ dm_gpio_set_value(&reset_gpio, 1);
+ }
+#else
+ dev_dbg(pcie->dev, "PCIE Reset on GPIO support is missing\n");
+#endif /* CONFIG_DM_GPIO */
+
+ pcie->first_busno = dev->seq;
+ pcie->dev = pci_get_controller(dev);
+
+ return pcie_advk_setup_hw(pcie);
+}
+
+/**
+ * pcie_advk_ofdata_to_platdata() - Translate from DT to device state
+ *
+ * @dev: A pointer to the device being operated on
+ *
+ * Translate relevant data from the device tree pertaining to device @dev into
+ * state that the driver will later make use of. This state is stored in the
+ * device's private data structure.
+ *
+ * Return: 0 on success, else -EINVAL
+ */
+static int pcie_advk_ofdata_to_platdata(struct udevice *dev)
+{
+ struct pcie_advk *pcie = dev_get_priv(dev);
+
+ /* Get the register base address */
+ pcie->base = (void *)dev_read_addr_index(dev, 0);
+ if ((fdt_addr_t)pcie->base == FDT_ADDR_T_NONE)
+ return -EINVAL;
+
+ return 0;
+}
+
+static const struct dm_pci_ops pcie_advk_ops = {
+ .read_config = pcie_advk_read_config,
+ .write_config = pcie_advk_write_config,
+};
+
+static const struct udevice_id pcie_advk_ids[] = {
+ { .compatible = "marvell,armada-37xx-pcie" },
+ { }
+};
+
+U_BOOT_DRIVER(pcie_advk) = {
+ .name = "pcie_advk",
+ .id = UCLASS_PCI,
+ .of_match = pcie_advk_ids,
+ .ops = &pcie_advk_ops,
+ .ofdata_to_platdata = pcie_advk_ofdata_to_platdata,
+ .probe = pcie_advk_probe,
+ .priv_auto_alloc_size = sizeof(struct pcie_advk),
+};