mmc: use an enumerated type to represent PARTITION_CONFIG fields
Modern eMMC v4+ devices have multiple hardware partitions per the JEDEC
specification described as:
Boot Area Partition 1
Boot Area Partition 2
RPMB Partition
General Purpose Partition 1
General Purpose Partition 2
General Purpose Partition 3
General Purpose Partition 4
User Data Area
These are referenced by fields in the PARTITION_CONFIG register
(Extended CSD Register 179) which is defined as:
bit 7: reserved
bit 6: BOOT_ACK
0x0: No boot acknowledge sent (default
0x1: Boot acknowledge sent during boot operation Bit
bit 5:3: BOOT_PARTITION_ENABLE
0x0: Device not boot enabled (default)
0x1: Boot Area partition 1 enabled for boot
0x2: Boot Area partition 2 enabled for boot
0x3-0x6: Reserved
0x7: User area enabled for boot
bit 2:0 PARTITION_ACCESS
0x0: No access to boot partition (default)
0x1: Boot Area partition 1
0x2: Boot Area partition 2
0x3: Replay Protected Memory Block (RPMB)
0x4: Access to General Purpose partition 1
0x5: Access to General Purpose partition 2
0x6: Access to General Purpose partition 3
0x7: Access to General Purpose partition 4
Note that setting PARTITION_ACCESS to 0x0 results in selecting the User
Data Area partition.
You can see above that the two fields BOOT_PARTITION_ENABLE and
PARTITION_ACCESS do not use the same enumerated values.
U-Boot uses a set of macros to access fields of the PARTITION_CONFIG
register:
There are various places in U-Boot where the BOOT_PARTITION_ENABLE field
is accessed via EXT_CSD_EXTRACT_PARTITION_ACCESS and converted to a
hardware partition consistent with the definition of the
PARTITION_ACCESS field which is also the value used to specify the
hardware partition of the various mmc_switch incarnations.
To add some sanity to the distinction between BOOT_PARTITION_ENABLE
(used to specify the active device on power-cycle) and PARTITION_ACCESS
(used to switch between hardware partitions) create two enumerated types
and use them wherever struct mmc * part_config is used or the above
macros are used.
This represents no code changes.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
diff --git a/arch/arm/mach-imx/image-container.c b/arch/arm/mach-imx/image-container.c
index 35da0ae..bcd4088 100644
--- a/arch/arm/mach-imx/image-container.c
+++ b/arch/arm/mach-imx/image-container.c
@@ -205,7 +205,7 @@
} else {
u8 part = EXT_CSD_EXTRACT_BOOT_PART(mmc->part_config);
- if (part == 1 || part == 2) {
+ if (part == EMMC_BOOT_PART_BOOT1 || part == EMMC_BOOT_PART_BOOT2) {
if (is_imx8qxp() && is_soc_rev(CHIP_REV_B))
offset = CONTAINER_HDR_MMCSD_OFFSET;
else
@@ -294,15 +294,15 @@
int part;
part = EXT_CSD_EXTRACT_BOOT_PART(mmc->part_config);
- if (part == 1 || part == 2) {
+ if (part == EMMC_BOOT_PART_BOOT1 || part == EMMC_BOOT_PART_BOOT2) {
unsigned long sec_set_off = 0;
bool sec_boot = false;
sec_boot = check_secondary_cnt_set(&sec_set_off);
if (sec_boot)
- part = (part == 1) ? 2 : 1;
- } else if (part == 7) {
- part = 0;
+ part = (part == EMMC_BOOT_PART_BOOT1) ? EMMC_HWPART_BOOT2 : EMMC_HWPART_BOOT1;
+ } else if (part == EMMC_BOOT_PART_USER) {
+ part = EMMC_HWPART_DEFAULT;
}
return part;