Add support for SX151x SPI GPIO Expanders
Signed-off-by: Viktar Palstsiuk <viktar.palstsiuk@promwad.com>
diff --git a/drivers/gpio/sx151x.c b/drivers/gpio/sx151x.c
new file mode 100644
index 0000000..167cf40
--- /dev/null
+++ b/drivers/gpio/sx151x.c
@@ -0,0 +1,242 @@
+/*
+ * (C) Copyright 2013
+ * Viktar Palstsiuk, Promwad, viktar.palstsiuk@promwad.com
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * Driver for Semtech SX151x SPI GPIO Expanders
+ */
+
+#include <common.h>
+#include <spi.h>
+#include <sx151x.h>
+
+#ifndef CONFIG_SX151X_SPI_BUS
+#define CONFIG_SX151X_SPI_BUS 0
+#endif
+
+/*
+ * The SX151x registers
+ */
+
+#ifdef CONFIG_SX151X_GPIO_COUNT_8
+/* 8bit: SX1511 */
+#define SX151X_REG_DIR 0x07
+#define SX151X_REG_DATA 0x08
+#else
+/* 16bit: SX1512 */
+#define SX151X_REG_DIR 0x0F
+#define SX151X_REG_DATA 0x11
+#endif
+#define SX151X_REG_RESET 0x7D
+
+static int sx151x_spi_write(int chip, unsigned char reg, unsigned char val)
+{
+ struct spi_slave *slave;
+ unsigned char buf[2];
+ int ret;
+
+ slave = spi_setup_slave(CONFIG_SX151X_SPI_BUS, chip, 1000000,
+ SPI_MODE_0);
+ if (!slave)
+ return 0;
+
+ spi_claim_bus(slave);
+
+ buf[0] = reg;
+ buf[1] = val;
+
+ ret = spi_xfer(slave, 16, buf, NULL, SPI_XFER_BEGIN | SPI_XFER_END);
+ if (ret < 0)
+ printf("spi%d.%d write fail: can't write %02x to %02x: %d\n",
+ CONFIG_SX151X_SPI_BUS, chip, val, reg, ret);
+ else
+ printf("spi%d.%d write 0x%02x to register 0x%02x\n",
+ CONFIG_SX151X_SPI_BUS, chip, val, reg);
+ spi_release_bus(slave);
+ spi_free_slave(slave);
+
+ return ret;
+}
+
+static int sx151x_spi_read(int chip, unsigned char reg)
+{
+ struct spi_slave *slave;
+ int ret;
+
+ slave = spi_setup_slave(CONFIG_SX151X_SPI_BUS, chip, 1000000,
+ SPI_MODE_0);
+ if (!slave)
+ return 0;
+
+ spi_claim_bus(slave);
+
+ ret = spi_w8r8(slave, reg | 0x80);
+ if (ret < 0)
+ printf("spi%d.%d read fail: can't read %02x: %d\n",
+ CONFIG_SX151X_SPI_BUS, chip, reg, ret);
+ else
+ printf("spi%d.%d read register 0x%02x: 0x%02x\n",
+ CONFIG_SX151X_SPI_BUS, chip, reg, ret);
+
+ spi_release_bus(slave);
+ spi_free_slave(slave);
+
+ return ret;
+}
+
+static inline void sx151x_find_cfg(int gpio, unsigned char *reg, unsigned char *mask)
+{
+ *reg -= gpio / 8;
+ *mask = 1 << (gpio % 8);
+}
+
+static int sx151x_write_cfg(int chip, unsigned char gpio, unsigned char reg, int val)
+{
+ unsigned char mask;
+ unsigned char data;
+ int ret;
+
+ sx151x_find_cfg(gpio, ®, &mask);
+ ret = sx151x_spi_read(chip, reg);
+ if (ret < 0)
+ return ret;
+ else
+ data = ret;
+ data &= ~mask;
+ data |= (val << (gpio % 8)) & mask;
+ return sx151x_spi_write(chip, reg, data);
+}
+
+int sx151x_get_value(int chip, int gpio)
+{
+ unsigned char reg = SX151X_REG_DATA;
+ unsigned char mask;
+ int ret;
+
+ sx151x_find_cfg(gpio, ®, &mask);
+ ret = sx151x_spi_read(chip, reg);
+ if (ret >= 0)
+ ret = (ret & mask) != 0 ? 1 : 0;
+
+ return ret;
+}
+
+int sx151x_set_value(int chip, int gpio, int val)
+{
+ return sx151x_write_cfg(chip, gpio, SX151X_REG_DATA, (val ? 1 : 0));
+}
+
+int sx151x_direction_input(int chip, int gpio)
+{
+ return sx151x_write_cfg(chip, gpio, SX151X_REG_DIR, 1);
+}
+
+int sx151x_direction_output(int chip, int gpio)
+{
+ return sx151x_write_cfg(chip, gpio, SX151X_REG_DIR, 0);
+}
+
+int sx151x_reset(int chip)
+{
+ int err;
+
+ err = sx151x_spi_write(chip, SX151X_REG_RESET, 0x12);
+ if (err < 0)
+ return err;
+
+ err = sx151x_spi_write(chip, SX151X_REG_RESET, 0x34);
+ return err;
+}
+
+#ifdef CONFIG_CMD_SX151X
+
+int do_sx151x(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ int ret = CMD_RET_USAGE, chip = 0, gpio = 0, val = 0;
+
+ if (argc < 3)
+ return CMD_RET_USAGE;
+
+ /* arg2 used as chip number */
+ chip = simple_strtoul(argv[2], NULL, 10);
+
+ if (strcmp(argv[1], "reset") == 0) {
+ ret = sx151x_reset(chip);
+ if (!ret) {
+ printf("Device at spi%d.%d was reset\n",
+ CONFIG_SX151X_SPI_BUS, chip);
+ }
+ return ret;
+ }
+
+ if (argc < 4)
+ return CMD_RET_USAGE;
+
+ /* arg3 used as gpio number */
+ gpio = simple_strtoul(argv[3], NULL, 10);
+
+ if (strcmp(argv[1], "get") == 0) {
+ ret = sx151x_get_value(chip, gpio);
+ if (ret < 0)
+ printf("Failed to get value at spi%d.%d gpio %d\n",
+ CONFIG_SX151X_SPI_BUS, chip, gpio);
+ else {
+ printf("Value at spi%d.%d gpio %d is %d\n",
+ CONFIG_SX151X_SPI_BUS, chip, gpio, ret);
+ ret = 0;
+ }
+ return ret;
+ }
+
+ if (argc < 5)
+ return CMD_RET_USAGE;
+
+ /* arg4 used as value or direction */
+ val = simple_strtoul(argv[4], NULL, 10);
+
+ if (strcmp(argv[1], "set") == 0) {
+ ret = sx151x_set_value(chip, gpio, val);
+ if (ret < 0)
+ printf("Failed to set value at spi%d.%d gpio %d\n",
+ CONFIG_SX151X_SPI_BUS, chip, gpio);
+ else
+ printf("New value at spi%d.%d gpio %d is %d\n",
+ CONFIG_SX151X_SPI_BUS, chip, gpio, val);
+ return ret;
+ } else if (strcmp(argv[1], "dir") == 0) {
+ if (val == 0)
+ ret = sx151x_direction_output(chip, gpio);
+ else
+ ret = sx151x_direction_input(chip, gpio);
+
+ if (ret < 0)
+ printf("Failed to set direction of spi%d.%d gpio %d\n",
+ CONFIG_SX151X_SPI_BUS, chip, gpio);
+ else
+ printf("New direction of spi%d.%d gpio %d is %d\n",
+ CONFIG_SX151X_SPI_BUS, chip, gpio, val);
+ return ret;
+ }
+
+ printf("Please see usage\n");
+
+ return ret;
+}
+
+U_BOOT_CMD(
+ sx151x, 5, 1, do_sx151x,
+ "sx151x gpio access",
+ "dir chip gpio 0|1\n"
+ " - set gpio direction (0 for output, 1 for input)\n"
+ "sx151x get chip gpio\n"
+ " - get gpio value\n"
+ "sx151x set chip gpio 0|1\n"
+ " - set gpio value\n"
+ "sx151x reset chip\n"
+ " - reset chip"
+);
+
+#endif /* CONFIG_CMD_SX151X */