ls1088a: Add VID support for QDS and RDB platforms
This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems.
It reads the fusesr register and changes the VDD accordingly by adjusting
the voltage via LTC3882 regulator.
This patch also takes care of the special case of 0.9V VDD is present in
fusesr register. In that case,it also changes the SERDES voltage by
disabling the SERDES, changing the SVDD and then re-enabling SERDES.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
diff --git a/include/configs/ls1088aqds.h b/include/configs/ls1088aqds.h
index ff2f916..bf76ed4 100644
--- a/include/configs/ls1088aqds.h
+++ b/include/configs/ls1088aqds.h
@@ -286,6 +286,17 @@
#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
+#define I2C_SVDD_MONITOR_ADDR 0x4F
+
+#define CONFIG_VID_FLS_ENV "ls1088aqds_vdd_mv"
+#define CONFIG_VID
+
+/* The lowest and highest voltage allowed for LS1088AQDS */
+#define VDD_MV_MIN 819
+#define VDD_MV_MAX 1212
+
+#define CONFIG_VOL_MONITOR_LTC3882_SET
+#define CONFIG_VOL_MONITOR_LTC3882_READ
/* PM Bus commands code for LTC3882*/
#define PMBUS_CMD_PAGE 0x0
diff --git a/include/configs/ls1088ardb.h b/include/configs/ls1088ardb.h
index 4c290c5..7b046e1 100644
--- a/include/configs/ls1088ardb.h
+++ b/include/configs/ls1088ardb.h
@@ -151,6 +151,7 @@
#endif
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
+#define QIXIS_BRDCFG4_OFFSET 0x54
#define QIXIS_LBMAP_SWITCH 2
#define QIXIS_QMAP_MASK 0xe0
#define QIXIS_QMAP_SHIFT 5
@@ -231,6 +232,17 @@
#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
+#define I2C_SVDD_MONITOR_ADDR 0x4F
+
+#define CONFIG_VID_FLS_ENV "ls1088ardb_vdd_mv"
+#define CONFIG_VID
+
+/* The lowest and highest voltage allowed for LS1088ARDB */
+#define VDD_MV_MIN 819
+#define VDD_MV_MAX 1212
+
+#define CONFIG_VOL_MONITOR_LTC3882_SET
+#define CONFIG_VOL_MONITOR_LTC3882_READ
/* PM Bus commands code for LTC3882*/
#define PMBUS_CMD_PAGE 0x0