armv8: ls1012a: Add support of ls1012ardb board
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
diff --git a/board/freescale/ls1012ardb/README b/board/freescale/ls1012ardb/README
new file mode 100644
index 0000000..453b432
--- /dev/null
+++ b/board/freescale/ls1012ardb/README
@@ -0,0 +1,54 @@
+Overview
+--------
+QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
+development platform, with a complete debugging environment.
+The LS1012ARDB board supports the QorIQ LS1012A processor and is
+optimized to support the high-bandwidth DDR3L memory and
+a full complement of high-speed SerDes ports.
+
+LS1012A SoC Overview
+--------------------
+Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS2080A
+SoC overview.
+
+LS1012ARDB board Overview
+-----------------------
+ - SERDES Connections, 4 lanes supporting:
+ - PCI Express - 3.0
+ - SGMII, SGMII 2.5
+ - SATA 3.0
+ - DDR Controller
+ - 16-bit, 1 GB DDR3L SDRAM memory, running at data rates up to 1 GT/s
+ -QSPI: A dual 1:3 switch, NX3L4357GM,115 (U35) drives the QSPI chip-select
+ signals to
+ - QSPI NOR flash memory (2 virtual banks)
+ - the QSPI emulator.s
+ - USB 3.0
+ - one high-speed USB 2.0/3.0 port.
+ - Two enhanced secure digital host controllers:
+ - SDHC1 controller can be connected to onboard SDHC connector
+ - SDHC2 controller: Three dual 1:4 mux/demux devices,
+ 74CBTLV3253DS (U30, U31, U33) drive the SDHC2 signals to eMMC,
+ SDIO WiFi, SPI, and Ardiuno shield
+ - 2 I2C controllers
+ - One SATA onboard connectors
+ - UART
+ - The LS1012A processor consists of two UART controllers,
+ out of which only UART1 is used on RDB.
+ - ARM JTAG support
+
+Booting Options
+---------------
+a) QSPI Flash Emu Boot
+b) QSPI Flash 1
+c) QSPI Flash 2
+
+QSPI flash map
+--------------
+Images | Size |QSPI Flash Address
+------------------------------------------
+RCW + PBI | 1MB | 0x4000_0000
+U-boot | 1MB | 0x4010_0000
+U-boot Env | 1MB | 0x4020_0000
+PPA FIT image | 2MB | 0x4050_0000
+Linux ITB | ~53MB | 0x40A0_0000