MIPS: Remove SLOW_DOWN_IO
CONF_SLOWDOWN_IO is never set for any target, so remove the dead code in
the SLOW_DOWN_IO macro. This is done in preparation for changes to
mips_io_port_base which can be avoided in this path by removing it
entirely.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
diff --git a/arch/mips/include/asm/io.h b/arch/mips/include/asm/io.h
index f71e342..4f9ec19 100644
--- a/arch/mips/include/asm/io.h
+++ b/arch/mips/include/asm/io.h
@@ -26,11 +26,6 @@
#include <spaces.h>
/*
- * Slowdown I/O port space accesses for antique hardware.
- */
-#undef CONF_SLOWDOWN_IO
-
-/*
* Raw operations are never swapped in software. OTOH values that raw
* operations are working on may or may not have been swapped by the bus
* hardware. An example use would be for flash memory that's used for
@@ -72,33 +67,6 @@
}
/*
- * Thanks to James van Artsdalen for a better timing-fix than
- * the two short jumps: using outb's to a nonexistent port seems
- * to guarantee better timings even on fast machines.
- *
- * On the other hand, I'd like to be sure of a non-existent port:
- * I feel a bit unsafe about using 0x80 (should be safe, though)
- *
- * Linus
- *
- */
-
-#define __SLOW_DOWN_IO \
- __asm__ __volatile__( \
- "sb\t$0,0x80(%0)" \
- : : "r" (mips_io_port_base));
-
-#ifdef CONF_SLOWDOWN_IO
-#ifdef REALLY_SLOW_IO
-#define SLOW_DOWN_IO { __SLOW_DOWN_IO; __SLOW_DOWN_IO; __SLOW_DOWN_IO; __SLOW_DOWN_IO; }
-#else
-#define SLOW_DOWN_IO __SLOW_DOWN_IO
-#endif
-#else
-#define SLOW_DOWN_IO
-#endif
-
-/*
* virt_to_phys - map virtual addresses to physical
* @address: address to remap
*
@@ -316,7 +284,7 @@
return pfx##ioswab##bwlq(__mem, __val); \
}
-#define __BUILD_IOPORT_SINGLE(pfx, bwlq, type, p, slow) \
+#define __BUILD_IOPORT_SINGLE(pfx, bwlq, type, p) \
\
static inline void pfx##out##bwlq##p(type val, unsigned long port) \
{ \
@@ -333,7 +301,6 @@
BUILD_BUG_ON(sizeof(type) > sizeof(unsigned long)); \
\
*__addr = __val; \
- slow; \
} \
\
static inline type pfx##in##bwlq##p(unsigned long port) \
@@ -346,7 +313,6 @@
BUILD_BUG_ON(sizeof(type) > sizeof(unsigned long)); \
\
__val = *__addr; \
- slow; \
\
return pfx##ioswab##bwlq(__addr, __val); \
}
@@ -367,8 +333,8 @@
BUILDIO_MEM(q, u64)
#define __BUILD_IOPORT_PFX(bus, bwlq, type) \
- __BUILD_IOPORT_SINGLE(bus, bwlq, type, ,) \
- __BUILD_IOPORT_SINGLE(bus, bwlq, type, _p, SLOW_DOWN_IO)
+ __BUILD_IOPORT_SINGLE(bus, bwlq, type, ) \
+ __BUILD_IOPORT_SINGLE(bus, bwlq, type, _p)
#define BUILDIO_IOPORT(bwlq, type) \
__BUILD_IOPORT_PFX(, bwlq, type) \