# SPDX-License-Identifier: GPL-2.0+
#
# Copyright (C) 2019, Pascal Linder <pascal.linder@edu.hefr.ch>

config VENDOR_KM
	bool
	help
	  Selected by any KM board to have additional configurations.

if VENDOR_KM

menu "KM Board Setup"

config SYS_I2C_INIT_BOARD
	def_bool y if ARM

config HUSH_INIT_VAR
	def_bool y

config KM_PNVRAM
	hex "Pseudo RAM"
	default 0x80000
	depends on !ARCH_SOCFPGA
	help
	  Start address of the pseudo non-volatile RAM for application.

config KM_PHRAM
	hex "Physical RAM"
	default 0x17F000 if ARM && !ARCH_LS1021A
	default 0x100000 if PPC || ARCH_LS1021A
	depends on !ARCH_SOCFPGA
	help
	  Start address of the physical RAM, which is the mounted /var folder.

config KM_RESERVED_PRAM
	hex "Reserved RAM"
	default 0x0 if MPC83xx
	default 0x1000 if MPC85xx || ARCH_LS1021A
	depends on !ARCH_SOCFPGA
	help
	  Reserved physical RAM area at the end of memory for special purposes.

config KM_CRAMFS_ADDR
	hex "CRAMFS Address"
	default 0x83000000 if ARCH_LS1021A
	default 0x3000000
	depends on !ARCH_SOCFPGA
	help
	  Start address of the CRAMFS containing the Linux kernel.

config KM_KERNEL_ADDR
	hex "Kernel Load Address"
	default 0x82000000 if ARCH_LS1021A
	default 0x2000000
	help
	  Address where to load Linux kernel in RAM.

config KM_FDT_ADDR
	hex "FDT Load Address"
	default 0x82FC0000 if ARCH_LS1021A
	default 0x2FC0000
	help
	  Address where to load flattened device tree in RAM.

config SYS_PAX_BASE
	hex "PAX IFC Base Address"
	default 0x78000000
	depends on ARCH_LS1021A
	help
	  IFC Base Address for PAXx FPGA.

config SYS_CLIPS_BASE
	hex "CLIPS IFC Base Address"
	default 0x78000000
	depends on ARCH_LS1021A
	help
	  IFC Base Address for CLIPS FPGA.

config KM_COMMON_ETH_INIT
	bool "Common Ethernet Initialization"
	default y if MPC83xx
	default n if MPC85xx || ARCH_SOCFPGA || ARCH_LS1021A
	help
	  Use the Ethernet initialization implemented in common code that
	  detects if a Piggy board is present.

config PIGGY_MAC_ADDRESS_OFFSET
	int "Piggy Address Offset"
	default 0
	help
	  MAC address offset for the Piggy board.

config KM_MVEXTSW_ADDR
	hex "Marvell Switch Address"
	depends on MV88E6352_SWITCH
	default 0x10
	help
	  Address of external Marvell switch.

config KM_IVM_BUS
	int "IVM I2C Bus"
	default 0 if ARCH_SOCFPGA
	default 1 if PPC || ARCH_LS1021A
	help
	  Identifier number of I2C bus, where the inventory EEPROM is connected to.

config SYS_IVM_EEPROM_ADR
	hex "IVM I2C Address"
	default 0x50
	help
	  I2C address of the EEPROM containing the inventory.

config SYS_IVM_EEPROM_MAX_LEN
	hex "IVM Length"
	default 0x400
	help
	  Maximum length of inventory in EEPROM.

config SYS_IVM_EEPROM_PAGE_LEN
	hex "IVM Page Size"
	default 0x100
	help
	  Page size of inventory in EEPROM.

config PG_WCOM_UBOOT_UPDATE_SUPPORTED
	bool "Enable U-boot Field Fail-Safe Update Functionality"
	default n
	help
	  Indicates that field fail-safe u-boot update is supported.
	  This functionality works only for designs that are booting
	  from parallel NOR flash.

config PG_WCOM_UBOOT_BOOTPACKAGE
	bool "U-boot Is Part Of Factory Boot-Package Image"
	default n
	help
	  Indicates that u-boot will be a part of the factory programmed
	  boot-package image.
	  Has to be set for original u-boot programmed at factory.

config PG_WCOM_UBOOT_UPDATE_TEXT_BASE
	hex "Text Base For U-boot Programmed Outside Factory"
	default 0xFFFFFFFF
	help
	  Text base of an updated u-boot that is not factory programmed but
	  later when the unit is rolled out on the field.
	  Has to be set for original u-boot programmed at factory.

config PG_WCOM_UBOOT_UPDATE
	bool "U-boot Is Part Of Factory Boot-Package Image"
	default n
	help
	  Indicates that u-boot will be a part of the embedded software and
	  programmed at field.
	  Has to be set for updated u-boot version programmed at field.

source "board/keymile/km83xx/Kconfig"
source "board/keymile/kmcent2/Kconfig"
source "board/keymile/pg-wcom-ls102xa/Kconfig"

endmenu

endif