[Blackfin]PATCH-1/2]: Remove obsolete blackfin port and add bf533 platform support
diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h
new file mode 100644
index 0000000..353a43c
--- /dev/null
+++ b/include/configs/bf533-stamp.h
@@ -0,0 +1,475 @@
+/*
+ * U-boot - Configuration file for BF533 STAMP board
+ */
+
+#ifndef __CONFIG_STAMP_H__
+#define __CONFIG_STAMP_H__
+
+#define CONFIG_STAMP 1
+#define CONFIG_RTC_BFIN 1
+#define CONFIG_BF533 1
+/*
+ * Boot Mode Set
+ * Blackfin can support several boot modes
+ */
+#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
+#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
+#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */
+/* Define the boot mode */
+#define BFIN_BOOT_MODE BF533_BYPASS_BOOT
+//#define BFIN_BOOT_MODE BF533_SPI_BOOT
+
+#define CONFIG_PANIC_HANG 1
+
+#define ADSP_BF531 0x31
+#define ADSP_BF532 0x32
+#define ADSP_BF533 0x33
+#define BFIN_CPU ADSP_BF533
+
+/* This sets the default state of the cache on U-Boot's boot */
+#define CONFIG_ICACHE_ON
+#define CONFIG_DCACHE_ON
+
+/* Define where the uboot will be loaded by on-chip boot rom */
+#define APP_ENTRY 0x00001000
+
+/*
+ * Stringize definitions - needed for environmental settings
+ */
+#define STRINGIZE2(x) #x
+#define STRINGIZE(x) STRINGIZE2(x)
+
+/*
+ * Board settings
+ *
+ */
+#define CONFIG_DRIVER_SMC91111 1
+#define CONFIG_SMC91111_BASE 0x20300300
+
+/* FLASH/ETHERNET uses the same address range */
+#define SHARED_RESOURCES 1
+
+/* Is I2C bit-banged? */
+#define CONFIG_SOFT_I2C 1
+
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PF_SCL PF3
+#define PF_SDA PF2
+
+/*
+ * Video splash screen support
+ */
+#define CONFIG_VIDEO 0
+
+#define CONFIG_VDSP 1
+
+/*
+ * Clock settings
+ *
+ */
+
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 11059200
+/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
+/* 1=CLKIN/2 */
+#define CONFIG_CLKIN_HALF 0
+/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */
+/* 1=bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */
+/* Values can range from 1-64 */
+#define CONFIG_VCO_MULT 36
+/* CONFIG_CCLK_DIV controls what the core clock divider is */
+/* Values can be 1, 2, 4, or 8 ONLY */
+#define CONFIG_CCLK_DIV 1
+/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 5
+/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */
+/* Values can range from 2-65535 */
+/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
+#define CONFIG_SPI_BAUD 2
+
+#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CONFIG_SPI_BAUD_INITBLOCK 4
+#endif
+
+
+/*
+ * Network settings
+ *
+ */
+
+#if (CONFIG_DRIVER_SMC91111)
+#if 0
+#define CONFIG_MII
+#endif
+
+/* network support */
+#define CONFIG_IPADDR 192.168.0.15
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_SERVERIP 192.168.0.2
+#define CONFIG_HOSTNAME STAMP
+#define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs
+
+/* To remove hardcoding and enable MAC storage in EEPROM */
+/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
+#endif /* CONFIG_DRIVER_SMC91111 */
+
+/*
+ * Flash settings
+ *
+ */
+
+#define CFG_FLASH_CFI /* The flash is CFI compatible */
+#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */
+#define CFG_FLASH_CFI_AMD_RESET
+
+#define CFG_FLASH_BASE 0x20000000
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
+
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR 0x20004000
+#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE)
+#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CFG_ENV_IS_IN_EEPROM 1
+#define CFG_ENV_OFFSET 0x4000
+#define CFG_ENV_HEADER (CFG_ENV_OFFSET + 0x12A) /* 0x12A is the length of LDR file header */
+#endif
+
+#define CFG_ENV_SIZE 0x2000
+#define CFG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */
+#define ENV_IS_EMBEDDED
+
+#define CFG_FLASH_ERASE_TOUT 30000 /* Timeout for Chip Erase (in ms) */
+#define CFG_FLASH_ERASEBLOCK_TOUT 5000 /* Timeout for Block Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
+
+/* JFFS Partition offset set */
+#define CFG_JFFS2_FIRST_BANK 0
+#define CFG_JFFS2_NUM_BANKS 1
+/* 512k reserved for u-boot */
+#define CFG_JFFS2_FIRST_SECTOR 11
+
+/*
+ * following timeouts shall be used once the
+ * Flash real protection is enabled
+ */
+#define CFG_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
+#define CFG_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */
+
+/*
+ * SDRAM settings & memory map
+ *
+ */
+
+#define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */
+#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */
+#define CONFIG_MEM_MT48LC64M4A2FB_7E 1
+
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
+#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
+#endif
+
+#define CFG_SDRAM_BASE 0x00000000
+
+#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 *1024)
+#define CFG_MEMTEST_END (CFG_MAX_RAM_SIZE - 0x80000 - 1)
+#define CONFIG_LOADADDR 0x01000000
+
+#define CFG_LOAD_ADDR CONFIG_LOADADDR
+#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CFG_GBL_DATA_SIZE 0x4000 /* Reserve 16k for Global Data */
+#define CONFIG_STACKSIZE (128*1024) /* regular stack */
+
+#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - 0x40000)
+#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
+#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
+
+/* Check to make sure everything fits in SDRAM */
+#if ((CFG_MONITOR_BASE + CFG_MONITOR_LEN) > CFG_MAX_RAM_SIZE)
+ #error Memory Map does not fit into configuration
+#endif
+
+#if ( CONFIG_CLKIN_HALF == 0 )
+#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
+#else
+#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 )
+#endif
+
+#if (CONFIG_PLL_BYPASS == 0)
+#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV )
+#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV )
+#else
+#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ
+#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
+#endif
+
+#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#if (CONFIG_SCLK_HZ / (2*CONFIG_SPI_BAUD) > 20000000)
+#define CONFIG_SPI_FLASH_FAST_READ 1 /* Needed if SPI_CLK > 20 MHz */
+#else
+#undef CONFIG_SPI_FLASH_FAST_READ
+#endif
+#endif
+/*
+ * Command settings
+ *
+ */
+
+#define CFG_LONGHELP 1
+#define CONFIG_CMDLINE_EDITING 1
+
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
+#endif
+ /* configuration lookup from the BOOTP/DHCP server, */
+ /* but not try to load any image using TFTP */
+
+#define CONFIG_BOOTDELAY 5
+#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#define CONFIG_BOOTCOMMAND "run ramboot"
+#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CONFIG_BOOTCOMMAND "eeprom read 0x1000000 0x100000 0x180000;icache on;dcache on;bootm 0x1000000"
+#endif
+
+#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
+
+#if (CONFIG_DRIVER_SMC91111)
+#define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \
+ CFG_CMD_PING | \
+ CFG_CMD_ELF | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_DATE)
+
+#else
+#define CONFIG_COMMANDS1 (CONFIG_CMD_DFL | \
+ CFG_CMD_ELF | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_DATE)
+
+#endif
+
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#if (CONFIG_DRIVER_SMC91111)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
+ "$(rootpath) console=ttyBF0,57600\0" \
+ "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
+ "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
+ "ramboot=tftpboot $(loadaddr) linux; " \
+ "run ramargs;run addip;bootelf\0" \
+ "nfsboot=tftpboot $(loadaddr) linux; " \
+ "run nfsargs;run addip;bootelf\0" \
+ "flashboot=bootm 0x20100000\0" \
+ "update=tftpboot $(loadaddr) u-boot.bin; " \
+ "protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \
+ "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \
+ ""
+#else
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+ "flashboot=bootm 0x20100000\0" \
+ ""
+#endif
+
+#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
+ "$(rootpath) console=ttyBF0,57600\0" \
+ "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
+ "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
+ "ramboot=tftpboot $(loadaddr) linux; " \
+ "run ramargs;run addip;bootelf\0" \
+ "nfsboot=tftpboot $(loadaddr) linux; " \
+ "run nfsargs;run addip;bootelf\0" \
+ "flashboot=bootm 0x20100000\0" \
+ "update=tftpboot $(loadaddr) u-boot.ldr;" \
+ "eeprom write $(loadaddr) 0x0 $(filesize);\0"\
+ ""
+#endif
+
+#ifdef CONFIG_SOFT_I2C
+#if (!CONFIG_SOFT_I2C)
+#undef CONFIG_SOFT_I2C
+#endif
+#endif
+
+#if (CONFIG_SOFT_I2C)
+#define CONFIG_COMMANDS2 CFG_CMD_I2C
+#else
+#define CONFIG_COMMANDS2 0
+#endif /* CONFIG_SOFT_I2C */
+
+#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
+#define CONFIG_COMMANDS ( CONFIG_COMMANDS1 | CONFIG_COMMANDS2 | CFG_CMD_DHCP)
+#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#define CONFIG_COMMANDS ( CONFIG_COMMANDS1 | CONFIG_COMMANDS2)
+#endif
+
+/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Console settings
+ *
+ */
+
+#define CONFIG_BAUDRATE 57600
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#if (BFIN_CPU == ADSP_BF531)
+#define CFG_PROMPT "serial_bf531> " /* Monitor Command Prompt */
+#elif (BFIN_CPU == ADSP_BF532)
+#define CFG_PROMPT "serial_bf532> " /* Monitor Command Prompt */
+#else
+#define CFG_PROMPT "serial_bf533> " /* Monitor Command Prompt */
+#endif
+#else
+#if (BFIN_CPU == ADSP_BF531)
+#define CFG_PROMPT "bf531> " /* Monitor Command Prompt */
+#elif (BFIN_CPU == ADSP_BF532)
+#define CFG_PROMPT "bf532> " /* Monitor Command Prompt */
+#else
+#define CFG_PROMPT "bf533> " /* Monitor Command Prompt */
+#endif
+#endif
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CONFIG_LOADS_ECHO 1
+
+/*
+ * I2C settings
+ * By default PF2 is used as SDA and PF3 as SCL on the Stamp board
+ */
+#if (CONFIG_SOFT_I2C)
+
+#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;")
+#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;")
+#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;")
+#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;")
+#define I2C_SDA(bit) if(bit) { \
+ *pFIO_FLAG_S = PF_SDA; \
+ asm("ssync;"); \
+ } \
+ else { \
+ *pFIO_FLAG_C = PF_SDA; \
+ asm("ssync;"); \
+ }
+#define I2C_SCL(bit) if(bit) { \
+ *pFIO_FLAG_S = PF_SCL; \
+ asm("ssync;"); \
+ } \
+ else { \
+ *pFIO_FLAG_C = PF_SCL; \
+ asm("ssync;"); \
+ }
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+#define CFG_I2C_SPEED 50000
+#define CFG_I2C_SLAVE 0xFE
+#endif /* CONFIG_SOFT_I2C */
+
+/*
+ * Compact Flash settings
+ */
+
+/* Enabled below option for CF support */
+/* #define CONFIG_STAMP_CF 1 */
+
+#if defined(CONFIG_STAMP_CF) && (CONFIG_COMMANDS & CFG_CMD_IDE)
+
+#define CONFIG_MISC_INIT_R 1
+#define CONFIG_DOS_PARTITION 1
+/*
+ * IDE/ATA stuff
+ */
+#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
+#undef CONFIG_IDE_LED /* no led for ide supported */
+#undef CONFIG_IDE_RESET /* no reset for ide supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+
+#define CFG_ATA_BASE_ADDR 0x20200000
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */
+
+#define CFG_ATA_STRIDE 2
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+
+#define CFG_HZ 1000 /* 1ms time tick */
+
+#define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
+
+#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */
+
+#define CONFIG_SPI
+
+#ifdef CONFIG_VIDEO
+#if (CONFIG_VIDEO)
+#define CONFIG_SPLASH_SCREEN 1
+#define CONFIG_SILENT_CONSOLE 1
+#else
+#undef CONFIG_VIDEO
+#endif
+#endif
+
+/*
+ * FLASH organization and environment definitions
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+
+/* 0xFF, 0xBBC3BBc3, 0x99B39983 */
+/*#define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
+#define AMBCTL0VAL (B1WAT_11 | B1RAT_11 | B1HT_3 | B1ST_4 | B1TT_4 | B1RDYPOL | \
+ B1RDYEN | B0WAT_11 | B0RAT_11 | B0HT_3 | B0ST_4 | B0TT_4 | B0RDYPOL | B0RDYEN)
+#define AMBCTL1VAL (B3WAT_9 | B3RAT_9 | B3HT_2 | B3ST_3 | B3TT_4 | B3RDYPOL | \
+ B3RDYEN | B2WAT_9 | B2RAT_9 | B2HT_2 | B2ST_4 | B2TT_4 | B2RDYPOL | B2RDYEN)
+*/
+#define AMGCTLVAL 0xFF
+#define AMBCTL0VAL 0xBBC3BBC3
+#define AMBCTL1VAL 0x99B39983
+#define CF_AMBCTL1VAL 0x99B3ffc2
+
+#ifdef CONFIG_VDSP
+#define ET_EXEC_VDSP 0x8
+#define SHT_STRTAB_VDSP 0x1
+#define ELFSHDRSIZE_VDSP 0x2C
+#define VDSP_ENTRY_ADDR 0xFFA00000
+#endif
+
+
+#endif