diff --git a/board/tcl/sl50/Kconfig b/board/tcl/sl50/Kconfig
new file mode 100644
index 0000000..390a476
--- /dev/null
+++ b/board/tcl/sl50/Kconfig
@@ -0,0 +1,31 @@
+if TARGET_AM335X_SL50
+
+config SYS_BOARD
+	default "sl50"
+
+config SYS_VENDOR
+	default "tcl"
+
+config SYS_SOC
+	default "am33xx"
+
+config SYS_CONFIG_NAME
+	default "am335x_sl50"
+
+config CONS_INDEX
+	int "UART used for console"
+	range 1 6
+	default 1
+	help
+	  The AM335x SoC has a total of 6 UARTs (UART0 to UART5 as referenced
+	  in documentation, etc) available to it.  Depending on your specific
+	  board you may want something other than UART0 as for example the IDK
+	  uses UART3 so enter 4 here.
+
+config DM_GPIO
+	default y
+
+config DM_SERIAL
+	default y
+
+endif
diff --git a/board/tcl/sl50/MAINTAINERS b/board/tcl/sl50/MAINTAINERS
new file mode 100644
index 0000000..29f1e3d
--- /dev/null
+++ b/board/tcl/sl50/MAINTAINERS
@@ -0,0 +1,6 @@
+SL50 BOARD
+M:	Enric Balletbo i Serra <enric.balletbo@collabora.com>
+S:	Maintained
+F:	board/tcl/sl50/
+F:	include/configs/am335x_sl50.h
+F:	configs/am335x_sl50_defconfig
diff --git a/board/tcl/sl50/Makefile b/board/tcl/sl50/Makefile
new file mode 100644
index 0000000..d4a548c
--- /dev/null
+++ b/board/tcl/sl50/Makefile
@@ -0,0 +1,13 @@
+#
+# Makefile
+#
+# Copyright (C) 2015 Toby Churchill Ltd - http://www.toby-churchill.com/
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+ifeq ($(CONFIG_SKIP_LOWLEVEL_INIT),)
+obj-y	:= mux.o
+endif
+
+obj-y	+= board.o
diff --git a/board/tcl/sl50/board.c b/board/tcl/sl50/board.c
new file mode 100644
index 0000000..e89ee35
--- /dev/null
+++ b/board/tcl/sl50/board.c
@@ -0,0 +1,386 @@
+/*
+ * board.c
+ *
+ * Board functions for TCL SL50 board
+ *
+ * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mem.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <cpsw.h>
+#include <power/tps65217.h>
+#include <power/tps65910.h>
+#include <environment.h>
+#include <watchdog.h>
+#include <environment.h>
+#include "board.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
+
+static const struct ddr_data ddr3_sl50_data = {
+	.datardsratio0 = MT41K256M16HA125E_RD_DQS,
+	.datawdsratio0 = MT41K256M16HA125E_WR_DQS,
+	.datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
+	.datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
+};
+
+static const struct cmd_control ddr3_sl50_cmd_ctrl_data = {
+	.cmd0csratio = MT41K256M16HA125E_RATIO,
+	.cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+	.cmd1csratio = MT41K256M16HA125E_RATIO,
+	.cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+	.cmd2csratio = MT41K256M16HA125E_RATIO,
+	.cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_sl50_emif_reg_data = {
+	.sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
+	.ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
+	.sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
+	.sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
+	.sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
+	.zq_config = MT41K256M16HA125E_ZQ_CFG,
+	.emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY,
+};
+
+#ifdef CONFIG_SPL_OS_BOOT
+int spl_start_uboot(void)
+{
+	/* break into full u-boot on 'c' */
+	if (serial_tstc() && serial_getc() == 'c')
+		return 1;
+
+#ifdef CONFIG_SPL_ENV_SUPPORT
+	env_init();
+	env_relocate_spec();
+	if (getenv_yesno("boot_os") != 1)
+		return 1;
+#endif
+
+	return 0;
+}
+#endif
+
+#define OSC	(V_OSCK/1000000)
+const struct dpll_params dpll_ddr_sl50 = {
+		400, OSC-1, 1, -1, -1, -1, -1};
+
+void am33xx_spl_board_init(void)
+{
+	int mpu_vdd;
+
+	/* Get the frequency */
+	dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
+
+	/* BeagleBone PMIC Code */
+	int usb_cur_lim;
+
+	if (i2c_probe(TPS65217_CHIP_PM))
+		return;
+
+	/*
+	 * Increase USB current limit to 1300mA or 1800mA and set
+	 * the MPU voltage controller as needed.
+	 */
+	if (dpll_mpu_opp100.m == MPUPLL_M_1000) {
+		usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1800MA;
+		mpu_vdd = TPS65217_DCDC_VOLT_SEL_1325MV;
+	} else {
+		usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA;
+		mpu_vdd = TPS65217_DCDC_VOLT_SEL_1275MV;
+	}
+
+	if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
+			       TPS65217_POWER_PATH,
+			       usb_cur_lim,
+			       TPS65217_USB_INPUT_CUR_LIMIT_MASK))
+		puts("tps65217_reg_write failure\n");
+
+	/* Set DCDC3 (CORE) voltage to 1.125V */
+	if (tps65217_voltage_update(TPS65217_DEFDCDC3,
+				    TPS65217_DCDC_VOLT_SEL_1125MV)) {
+		puts("tps65217_voltage_update failure\n");
+		return;
+	}
+
+	/* Set CORE Frequencies to OPP100 */
+	do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
+
+	/* Set DCDC2 (MPU) voltage */
+	if (tps65217_voltage_update(TPS65217_DEFDCDC2, mpu_vdd)) {
+		puts("tps65217_voltage_update failure\n");
+		return;
+	}
+
+	/*
+	 * Set LDO3 to 1.8V and LDO4 to 3.3V
+	 */
+	if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
+			       TPS65217_DEFLS1,
+			       TPS65217_LDO_VOLTAGE_OUT_1_8,
+			       TPS65217_LDO_MASK))
+		puts("tps65217_reg_write failure\n");
+
+	if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
+			       TPS65217_DEFLS2,
+			       TPS65217_LDO_VOLTAGE_OUT_3_3,
+			       TPS65217_LDO_MASK))
+		puts("tps65217_reg_write failure\n");
+
+	/* Set MPU Frequency to what we detected now that voltages are set */
+	do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
+}
+
+const struct dpll_params *get_dpll_ddr_params(void)
+{
+	enable_i2c0_pin_mux();
+	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
+
+	return &dpll_ddr_sl50;
+}
+
+void set_uart_mux_conf(void)
+{
+#if CONFIG_CONS_INDEX == 1
+	enable_uart0_pin_mux();
+#elif CONFIG_CONS_INDEX == 2
+	enable_uart1_pin_mux();
+#elif CONFIG_CONS_INDEX == 3
+	enable_uart2_pin_mux();
+#elif CONFIG_CONS_INDEX == 4
+	enable_uart3_pin_mux();
+#elif CONFIG_CONS_INDEX == 5
+	enable_uart4_pin_mux();
+#elif CONFIG_CONS_INDEX == 6
+	enable_uart5_pin_mux();
+#endif
+}
+
+void set_mux_conf_regs(void)
+{
+	enable_board_pin_mux();
+}
+
+const struct ctrl_ioregs ioregs_evmsk = {
+	.cm0ioctl		= MT41J128MJT125_IOCTRL_VALUE,
+	.cm1ioctl		= MT41J128MJT125_IOCTRL_VALUE,
+	.cm2ioctl		= MT41J128MJT125_IOCTRL_VALUE,
+	.dt0ioctl		= MT41J128MJT125_IOCTRL_VALUE,
+	.dt1ioctl		= MT41J128MJT125_IOCTRL_VALUE,
+};
+
+const struct ctrl_ioregs ioregs_bonelt = {
+	.cm0ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
+	.cm1ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
+	.cm2ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
+	.dt0ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
+	.dt1ioctl		= MT41K256M16HA125E_IOCTRL_VALUE,
+};
+
+const struct ctrl_ioregs ioregs_evm15 = {
+	.cm0ioctl		= MT41J512M8RH125_IOCTRL_VALUE,
+	.cm1ioctl		= MT41J512M8RH125_IOCTRL_VALUE,
+	.cm2ioctl		= MT41J512M8RH125_IOCTRL_VALUE,
+	.dt0ioctl		= MT41J512M8RH125_IOCTRL_VALUE,
+	.dt1ioctl		= MT41J512M8RH125_IOCTRL_VALUE,
+};
+
+const struct ctrl_ioregs ioregs = {
+	.cm0ioctl		= MT47H128M16RT25E_IOCTRL_VALUE,
+	.cm1ioctl		= MT47H128M16RT25E_IOCTRL_VALUE,
+	.cm2ioctl		= MT47H128M16RT25E_IOCTRL_VALUE,
+	.dt0ioctl		= MT47H128M16RT25E_IOCTRL_VALUE,
+	.dt1ioctl		= MT47H128M16RT25E_IOCTRL_VALUE,
+};
+
+void sdram_init(void)
+{
+	config_ddr(400, &ioregs_bonelt,
+		   &ddr3_sl50_data,
+		   &ddr3_sl50_cmd_ctrl_data,
+		   &ddr3_sl50_emif_reg_data, 0);
+}
+#endif
+
+/*
+ * Basic board specific setup.  Pinmux has been handled already.
+ */
+int board_init(void)
+{
+#if defined(CONFIG_HW_WATCHDOG)
+	hw_watchdog_init();
+#endif
+
+	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+	return 0;
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
+{
+	return 0;
+}
+#endif
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+static void cpsw_control(int enabled)
+{
+	/* VTP can be added here */
+
+	return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+	{
+		.slave_reg_ofs	= 0x208,
+		.sliver_reg_ofs	= 0xd80,
+		.phy_addr	= 0,
+	},
+	{
+		.slave_reg_ofs	= 0x308,
+		.sliver_reg_ofs	= 0xdc0,
+		.phy_addr	= 1,
+	},
+};
+
+static struct cpsw_platform_data cpsw_data = {
+	.mdio_base		= CPSW_MDIO_BASE,
+	.cpsw_base		= CPSW_BASE,
+	.mdio_div		= 0xff,
+	.channels		= 8,
+	.cpdma_reg_ofs		= 0x800,
+	.slaves			= 1,
+	.slave_data		= cpsw_slaves,
+	.ale_reg_ofs		= 0xd00,
+	.ale_entries		= 1024,
+	.host_port_reg_ofs	= 0x108,
+	.hw_stats_reg_ofs	= 0x900,
+	.bd_ram_ofs		= 0x2000,
+	.mac_control		= (1 << 5),
+	.control		= cpsw_control,
+	.host_port_num		= 0,
+	.version		= CPSW_CTRL_VERSION_2,
+};
+#endif
+
+/*
+ * This function will:
+ * Read the eFuse for MAC addresses, and set ethaddr/eth1addr/usbnet_devaddr
+ * in the environment
+ * Perform fixups to the PHY present on certain boards.  We only need this
+ * function in:
+ * - SPL with either CPSW or USB ethernet support
+ * - Full U-Boot, with either CPSW or USB ethernet
+ * Build in only these cases to avoid warnings about unused variables
+ * when we build an SPL that has neither option but full U-Boot will.
+ */
+#if ((defined(CONFIG_SPL_ETH_SUPPORT) || defined(CONFIG_SPL_USBETH_SUPPORT)) \
+		&& defined(CONFIG_SPL_BUILD)) || \
+	((defined(CONFIG_DRIVER_TI_CPSW) || \
+	  defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET)) && \
+	 !defined(CONFIG_SPL_BUILD))
+int board_eth_init(bd_t *bis)
+{
+	int rv, n = 0;
+	uint8_t mac_addr[6];
+	uint32_t mac_hi, mac_lo;
+
+	/* try reading mac address from efuse */
+	mac_lo = readl(&cdev->macid0l);
+	mac_hi = readl(&cdev->macid0h);
+	mac_addr[0] = mac_hi & 0xFF;
+	mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+	mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+	mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+	mac_addr[4] = mac_lo & 0xFF;
+	mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+#if (defined(CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)) || \
+	(defined(CONFIG_SPL_ETH_SUPPORT) && defined(CONFIG_SPL_BUILD))
+	if (!getenv("ethaddr")) {
+		printf("<ethaddr> not set. Validating first E-fuse MAC\n");
+
+		if (is_valid_ethaddr(mac_addr))
+			eth_setenv_enetaddr("ethaddr", mac_addr);
+	}
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+
+	mac_lo = readl(&cdev->macid1l);
+	mac_hi = readl(&cdev->macid1h);
+	mac_addr[0] = mac_hi & 0xFF;
+	mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+	mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+	mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+	mac_addr[4] = mac_lo & 0xFF;
+	mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+	if (!getenv("eth1addr")) {
+		if (is_valid_ethaddr(mac_addr))
+			eth_setenv_enetaddr("eth1addr", mac_addr);
+	}
+
+
+	writel(MII_MODE_ENABLE, &cdev->miisel);
+	cpsw_slaves[0].phy_if = cpsw_slaves[1].phy_if =
+				PHY_INTERFACE_MODE_MII;
+
+	rv = cpsw_register(&cpsw_data);
+	if (rv < 0)
+		printf("Error %d registering CPSW switch\n", rv);
+	else
+		n += rv;
+#endif
+
+	/*
+	 *
+	 * CPSW RGMII Internal Delay Mode is not supported in all PVT
+	 * operating points.  So we must set the TX clock delay feature
+	 * in the AR8051 PHY.  Since we only support a single ethernet
+	 * device in U-Boot, we only do this for the first instance.
+	 */
+#define AR8051_PHY_DEBUG_ADDR_REG	0x1d
+#define AR8051_PHY_DEBUG_DATA_REG	0x1e
+#define AR8051_DEBUG_RGMII_CLK_DLY_REG	0x5
+#define AR8051_RGMII_TX_CLK_DLY		0x100
+
+#endif
+#if defined(CONFIG_USB_ETHER) && \
+	(!defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_USBETH_SUPPORT))
+	if (is_valid_ether_addr(mac_addr))
+		eth_setenv_enetaddr("usbnet_devaddr", mac_addr);
+
+	rv = usb_eth_initialize(bis);
+	if (rv < 0)
+		printf("Error %d registering USB_ETHER\n", rv);
+	else
+		n += rv;
+#endif
+	return n;
+}
+#endif
diff --git a/board/tcl/sl50/board.h b/board/tcl/sl50/board.h
new file mode 100644
index 0000000..ae2ef6b
--- /dev/null
+++ b/board/tcl/sl50/board.h
@@ -0,0 +1,22 @@
+/*
+ * board.h
+ *
+ * TCL SL50 boards information header
+ *
+ * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+void enable_uart0_pin_mux(void);
+void enable_uart1_pin_mux(void);
+void enable_uart2_pin_mux(void);
+void enable_uart3_pin_mux(void);
+void enable_uart4_pin_mux(void);
+void enable_uart5_pin_mux(void);
+void enable_i2c0_pin_mux(void);
+void enable_board_pin_mux(void);
+#endif
diff --git a/board/tcl/sl50/mux.c b/board/tcl/sl50/mux.c
new file mode 100644
index 0000000..e0d76ef
--- /dev/null
+++ b/board/tcl/sl50/mux.c
@@ -0,0 +1,154 @@
+/*
+ * mux.c
+ *
+ * Copyright (C) 2011, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include <i2c.h>
+#include "board.h"
+
+static struct module_pin_mux uart0_pin_mux[] = {
+	{OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* UART0_RXD */
+	{OFFSET(uart0_txd), (MODE(0) | PULLUDEN)},		/* UART0_TXD */
+	{-1},
+};
+
+static struct module_pin_mux uart1_pin_mux[] = {
+	{OFFSET(uart1_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)},	/* UART1_RXD */
+	{OFFSET(uart1_txd), (MODE(0) | PULLUDEN)},		/* UART1_TXD */
+	{-1},
+};
+
+static struct module_pin_mux uart2_pin_mux[] = {
+	{OFFSET(spi0_sclk), (MODE(1) | PULLUP_EN | RXACTIVE)},	/* UART2_RXD */
+	{OFFSET(spi0_d0), (MODE(1) | PULLUDEN)},		/* UART2_TXD */
+	{-1},
+};
+
+static struct module_pin_mux uart3_pin_mux[] = {
+	{OFFSET(spi0_cs1), (MODE(1) | PULLUP_EN | RXACTIVE)},	/* UART3_RXD */
+	{OFFSET(ecap0_in_pwm0_out), (MODE(1) | PULLUDEN)},	/* UART3_TXD */
+	{-1},
+};
+
+static struct module_pin_mux uart4_pin_mux[] = {
+	{OFFSET(gpmc_wait0), (MODE(6) | PULLUP_EN | RXACTIVE)},	/* UART4_RXD */
+	{OFFSET(gpmc_wpn), (MODE(6) | PULLUDEN)},		/* UART4_TXD */
+	{-1},
+};
+
+static struct module_pin_mux uart5_pin_mux[] = {
+	{OFFSET(lcd_data9), (MODE(4) | PULLUP_EN | RXACTIVE)},	/* UART5_RXD */
+	{OFFSET(lcd_data8), (MODE(4) | PULLUDEN)},		/* UART5_TXD */
+	{-1},
+};
+
+static struct module_pin_mux mmc0_pin_mux[] = {
+	{OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT3 */
+	{OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT2 */
+	{OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT1 */
+	{OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_DAT0 */
+	{OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_CLK */
+	{OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)},	/* MMC0_CMD */
+	{OFFSET(mcasp0_aclkr), (MODE(4) | RXACTIVE)},		/* MMC0_WP */
+	{OFFSET(spi0_cs1), (MODE(5) | RXACTIVE | PULLUP_EN)},	/* MMC0_CD */
+	{-1},
+};
+
+static struct module_pin_mux mmc1_pin_mux[] = {
+	{OFFSET(gpmc_ad3), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT3 */
+	{OFFSET(gpmc_ad2), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT2 */
+	{OFFSET(gpmc_ad1), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT1 */
+	{OFFSET(gpmc_ad0), (MODE(1) | RXACTIVE | PULLUP_EN)},	/* MMC1_DAT0 */
+	{OFFSET(gpmc_csn1), (MODE(2) | RXACTIVE | PULLUP_EN)},	/* MMC1_CLK */
+	{OFFSET(gpmc_csn2), (MODE(2) | RXACTIVE | PULLUP_EN)},	/* MMC1_CMD */
+	{OFFSET(gpmc_csn0), (MODE(7) | RXACTIVE | PULLUP_EN)},	/* MMC1_WP */
+	{OFFSET(gpmc_advn_ale), (MODE(7) | RXACTIVE | PULLUP_EN)},	/* MMC1_CD */
+	{-1},
+};
+
+static struct module_pin_mux i2c0_pin_mux[] = {
+	{OFFSET(i2c0_sda), (MODE(0) | RXACTIVE |
+			PULLUDEN | SLEWCTRL)}, /* I2C_DATA */
+	{OFFSET(i2c0_scl), (MODE(0) | RXACTIVE |
+			PULLUDEN | SLEWCTRL)}, /* I2C_SCLK */
+	{-1},
+};
+
+static struct module_pin_mux i2c1_pin_mux[] = {
+	{OFFSET(spi0_d1), (MODE(2) | RXACTIVE |
+			PULLUDEN | SLEWCTRL)},	/* I2C_DATA */
+	{OFFSET(spi0_cs0), (MODE(2) | RXACTIVE |
+			PULLUDEN | SLEWCTRL)},	/* I2C_SCLK */
+	{-1},
+};
+
+static struct module_pin_mux mii1_pin_mux[] = {
+	{OFFSET(mii1_rxerr), MODE(0) | RXACTIVE},	/* MII1_RXERR */
+	{OFFSET(mii1_txen), MODE(0)},			/* MII1_TXEN */
+	{OFFSET(mii1_rxdv), MODE(0) | RXACTIVE},	/* MII1_RXDV */
+	{OFFSET(mii1_txd3), MODE(0)},			/* MII1_TXD3 */
+	{OFFSET(mii1_txd2), MODE(0)},			/* MII1_TXD2 */
+	{OFFSET(mii1_txd1), MODE(0)},			/* MII1_TXD1 */
+	{OFFSET(mii1_txd0), MODE(0)},			/* MII1_TXD0 */
+	{OFFSET(mii1_txclk), MODE(0) | RXACTIVE},	/* MII1_TXCLK */
+	{OFFSET(mii1_rxclk), MODE(0) | RXACTIVE},	/* MII1_RXCLK */
+	{OFFSET(mii1_rxd3), MODE(0) | RXACTIVE},	/* MII1_RXD3 */
+	{OFFSET(mii1_rxd2), MODE(0) | RXACTIVE},	/* MII1_RXD2 */
+	{OFFSET(mii1_rxd1), MODE(0) | RXACTIVE},	/* MII1_RXD1 */
+	{OFFSET(mii1_rxd0), MODE(0) | RXACTIVE},	/* MII1_RXD0 */
+	{OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN}, /* MDIO_DATA */
+	{OFFSET(mdio_clk), MODE(0) | PULLUP_EN},	/* MDIO_CLK */
+	{-1},
+};
+
+
+void enable_uart0_pin_mux(void)
+{
+	configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_uart1_pin_mux(void)
+{
+	configure_module_pin_mux(uart1_pin_mux);
+}
+
+void enable_uart2_pin_mux(void)
+{
+	configure_module_pin_mux(uart2_pin_mux);
+}
+
+void enable_uart3_pin_mux(void)
+{
+	configure_module_pin_mux(uart3_pin_mux);
+}
+
+void enable_uart4_pin_mux(void)
+{
+	configure_module_pin_mux(uart4_pin_mux);
+}
+
+void enable_uart5_pin_mux(void)
+{
+	configure_module_pin_mux(uart5_pin_mux);
+}
+
+void enable_i2c0_pin_mux(void)
+{
+	configure_module_pin_mux(i2c0_pin_mux);
+}
+
+void enable_board_pin_mux(void)
+{
+	configure_module_pin_mux(i2c1_pin_mux);
+	configure_module_pin_mux(mii1_pin_mux);
+	configure_module_pin_mux(mmc0_pin_mux);
+	configure_module_pin_mux(mmc1_pin_mux);
+}