rockchip: Add basic support for jerry
This builds and displays an SPL message, but does not function beyond that.
Signed-off-by: Simon Glass <sjg@chromium.org>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index ba3b71d..3babe65 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -16,7 +16,8 @@
exynos5800-peach-pi.dtb \
exynos5422-odroidxu3.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += \
- rk3288-firefly.dtb
+ rk3288-firefly.dtb \
+ rk3288-jerry.dtb
dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
tegra20-medcom-wide.dtb \
tegra20-paz00.dtb \
diff --git a/arch/arm/dts/cros-ec-sbs.dtsi b/arch/arm/dts/cros-ec-sbs.dtsi
new file mode 100644
index 0000000..3f35d20
--- /dev/null
+++ b/arch/arm/dts/cros-ec-sbs.dtsi
@@ -0,0 +1,16 @@
+/*
+ * Smart battery dts fragment for devices that use cros-ec-sbs
+ *
+ * Copyright (c) 2015 Google, Inc
+ *
+ * SPDX-License-Identifier: GPL-2.0
+*/
+
+&i2c_tunnel {
+ battery: sbs-battery@b {
+ compatible = "sbs,sbs-battery";
+ reg = <0xb>;
+ sbs,i2c-retry-count = <2>;
+ sbs,poll-retry-count = <1>;
+ };
+};
diff --git a/arch/arm/dts/rk3288-jerry.dts b/arch/arm/dts/rk3288-jerry.dts
new file mode 100644
index 0000000..da37ea8
--- /dev/null
+++ b/arch/arm/dts/rk3288-jerry.dts
@@ -0,0 +1,203 @@
+/*
+ * Google Veyron Jerry Rev 3+ board device tree source
+ *
+ * Copyright 2014 Google, Inc
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+/dts-v1/;
+#include "rk3288-veyron-chromebook.dtsi"
+#include "cros-ec-sbs.dtsi"
+
+/ {
+ model = "Google Jerry";
+ compatible = "google,veyron-jerry-rev7", "google,veyron-jerry-rev6",
+ "google,veyron-jerry-rev5", "google,veyron-jerry-rev4",
+ "google,veyron-jerry-rev3", "google,veyron-jerry",
+ "google,veyron", "rockchip,rk3288";
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ panel_regulator: panel-regualtor {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio7 14 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_enable_h>;
+ regulator-name = "panel_regulator";
+ vin-supply = <&vcc33_sys>;
+ };
+
+ vcc18_lcd: vcc18-lcd {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&avdd_1v8_disp_en>;
+ regulator-name = "vcc18_lcd";
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc18_wl>;
+ };
+
+ backlight_regulator: backlight-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio2 12 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_pwr_en>;
+ regulator-name = "backlight_regulator";
+ vin-supply = <&vcc33_sys>;
+ startup-delay-us = <15000>;
+ };
+};
+
+&gpio_keys {
+ power {
+ gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&backlight {
+ power-supply = <&backlight_regulator>;
+};
+
+&panel {
+ power-supply= <&panel_regulator>;
+};
+
+&rk808 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l &dvs_1 &dvs_2>;
+ dvs-gpios = <&gpio7 12 GPIO_ACTIVE_HIGH>,
+ <&gpio7 15 GPIO_ACTIVE_HIGH>;
+
+ regulators {
+ mic_vcc: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "mic_vcc";
+ regulator-suspend-mem-disabled;
+ };
+ };
+};
+
+&sdmmc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd_disabled &sdmmc_cd_gpio
+ &sdmmc_bus4>;
+ disable-wp;
+};
+
+&vcc_5v {
+ enable-active-high;
+ gpio = <&gpio7 21 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&drv_5v>;
+};
+
+&vcc50_hdmi {
+ enable-active-high;
+ gpio = <&gpio5 19 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc50_hdmi_en>;
+};
+
+&edp {
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_hpd>;
+};
+
+&pinctrl {
+ backlight {
+ bl_pwr_en: bl_pwr_en {
+ rockchip,pins = <2 12 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ buck-5v {
+ drv_5v: drv-5v {
+ rockchip,pins = <7 21 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ edp {
+ edp_hpd: edp_hpd {
+ rockchip,pins = <7 11 RK_FUNC_2 &pcfg_pull_down>;
+ };
+ };
+
+ emmc {
+ /* Make sure eMMC is not in reset */
+ emmc_deassert_reset: emmc-deassert-reset {
+ rockchip,pins = <2 9 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ hdmi {
+ vcc50_hdmi_en: vcc50-hdmi-en {
+ rockchip,pins = <5 19 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ lcd {
+ lcd_enable_h: lcd-en {
+ rockchip,pins = <7 14 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ avdd_1v8_disp_en: avdd-1v8-disp-en {
+ rockchip,pins = <2 13 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ dvs_1: dvs-1 {
+ rockchip,pins = <7 12 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+
+ dvs_2: dvs-2 {
+ rockchip,pins = <7 15 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+};
+
+&i2c4 {
+ status = "okay";
+
+ /*
+ * Trackpad pin control is shared between Elan and Synaptics devices
+ * so we have to pull it up to the bus level.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_xfer &trackpad_int>;
+
+ trackpad@15 {
+ compatible = "elan,i2c_touchpad";
+ interrupt-parent = <&gpio7>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+ /*
+ * Remove the inherited pinctrl settings to avoid clashing
+ * with bus-wide ones.
+ */
+ /delete-property/pinctrl-names;
+ /delete-property/pinctrl-0;
+ reg = <0x15>;
+ vcc-supply = <&vcc33_io>;
+ wakeup-source;
+ };
+
+ trackpad@2c {
+ compatible = "hid-over-i2c";
+ interrupt-parent = <&gpio7>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+ reg = <0x2c>;
+ hid-descr-addr = <0x0020>;
+ vcc-supply = <&vcc33_io>;
+ wakeup-source;
+ };
+};
diff --git a/arch/arm/dts/rk3288-veyron-chromebook.dtsi b/arch/arm/dts/rk3288-veyron-chromebook.dtsi
new file mode 100644
index 0000000..6d619c9
--- /dev/null
+++ b/arch/arm/dts/rk3288-veyron-chromebook.dtsi
@@ -0,0 +1,200 @@
+/*
+ * Google Veyron (and derivatives) board device tree source
+ *
+ * Copyright 2014 Google, Inc
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <dt-bindings/clock/rockchip,rk808.h>
+#include <dt-bindings/input/input.h>
+#include "rk3288-veyron.dtsi"
+
+/ {
+ aliases {
+ i2c20 = &i2c_tunnel;
+ };
+
+ gpio_keys: gpio-keys {
+ pinctrl-0 = <&pwr_key_h &ap_lid_int_l>;
+ lid {
+ label = "Lid";
+ gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+ linux,code = <0>; /* SW_LID */
+ linux,input-type = <5>; /* EV_SW */
+ debounce-interval = <1>;
+ gpio-key,wakeup;
+ };
+ };
+
+ gpio-charger {
+ compatible = "gpio-charger";
+ gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ac_present_ap>;
+ charger-type = "mains";
+ };
+
+ /* A non-regulated voltage from power supply or battery */
+ vccsys: vccsys {
+ compatible = "regulator-fixed";
+ regulator-name = "vccsys";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vcc33_sys: vcc33-sys {
+ vin-supply = <&vccsys>;
+ };
+
+ vcc_5v: vcc-5v {
+ vin-supply = <&vccsys>;
+ };
+
+ /* This turns on vbus for host1 (dwc2) */
+ vcc5_host1: vcc5-host1-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&host1_pwr_en>;
+ regulator-name = "vcc5_host1";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ /* This turns on vbus for otg for host mode (dwc2) */
+ vcc5v_otg: vcc5v-otg-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usbotg_pwren_h>;
+ regulator-name = "vcc5_host2";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&rk808 {
+ regulators {
+ vcc33_ccd: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc33_ccd";
+ regulator-suspend-mem-disabled;
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ cros_ec: ec@0 {
+ compatible = "google,cros-ec-spi";
+ spi-max-frequency = <3000000>;
+ interrupt-parent = <&gpio7>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ec_int>;
+ reg = <0>;
+ google,cros-ec-spi-pre-delay = <30>;
+
+ i2c_tunnel: i2c-tunnel {
+ compatible = "google,cros-ec-i2c-tunnel";
+ google,remote-bus = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
+
+&i2c4 {
+ trackpad@15 {
+ compatible = "elan,i2c_touchpad";
+ interrupt-parent = <&gpio7>;
+ interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&trackpad_int>;
+ reg = <0x15>;
+ vcc-supply = <&vcc33_io>;
+ wakeup-source;
+ };
+};
+
+&pinctrl {
+ pinctrl-0 = <
+ /* Common for sleep and wake, but no owners */
+ &ddr0_retention
+ &ddrio_pwroff
+ &global_pwroff
+
+ /* Wake only */
+ &suspend_l_wake
+ &bt_dev_wake_awake
+ >;
+ pinctrl-1 = <
+ /* Common for sleep and wake, but no owners */
+ &ddr0_retention
+ &ddrio_pwroff
+ &global_pwroff
+
+ /* Sleep only */
+ &suspend_l_sleep
+ &bt_dev_wake_sleep
+ >;
+
+ buttons {
+ ap_lid_int_l: ap-lid-int-l {
+ rockchip,pins = <0 6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ charger {
+ ac_present_ap: ac-present-ap {
+ rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ cros-ec {
+ ec_int: ec-int {
+ rockchip,pins = <7 7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdmmc {
+ sdmmc_wp_gpio: sdmmc-wp-gpio {
+ rockchip,pins = <7 10 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ suspend {
+ suspend_l_wake: suspend-l-wake {
+ rockchip,pins = <0 17 RK_FUNC_GPIO &pcfg_output_low>;
+ };
+
+ suspend_l_sleep: suspend-l-sleep {
+ rockchip,pins = <0 17 RK_FUNC_GPIO &pcfg_output_high>;
+ };
+ };
+
+ trackpad {
+ trackpad_int: trackpad-int {
+ rockchip,pins = <7 3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb-host {
+ host1_pwr_en: host1-pwr-en {
+ rockchip,pins = <0 11 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ usbotg_pwren_h: usbotg-pwren-h {
+ rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+#include "cros-ec-keyboard.dtsi"
diff --git a/arch/arm/dts/rk3288-veyron.dtsi b/arch/arm/dts/rk3288-veyron.dtsi
new file mode 100644
index 0000000..7e37158
--- /dev/null
+++ b/arch/arm/dts/rk3288-veyron.dtsi
@@ -0,0 +1,844 @@
+/*
+ * Google Veyron (and derivatives) board device tree source
+ *
+ * Copyright 2014 Google, Inc
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#include <dt-bindings/clock/rockchip,rk808.h>
+#include <dt-bindings/input/input.h>
+#include "rk3288.dtsi"
+
+/ {
+ memory {
+ reg = <0x0 0x80000000>;
+ };
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ config {
+ u-boot,dm-pre-reloc;
+ u-boot,boot0 = &spi_flash;
+ };
+
+ firmware {
+ chromeos {
+ pinctrl-names = "default";
+ pinctrl-0 = <&fw_wp_ap>;
+ write-protect-gpio = <&gpio7 6 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ brightness-levels = <
+ 0 1 2 3 4 5 6 7
+ 8 9 10 11 12 13 14 15
+ 16 17 18 19 20 21 22 23
+ 24 25 26 27 28 29 30 31
+ 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47
+ 48 49 50 51 52 53 54 55
+ 56 57 58 59 60 61 62 63
+ 64 65 66 67 68 69 70 71
+ 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87
+ 88 89 90 91 92 93 94 95
+ 96 97 98 99 100 101 102 103
+ 104 105 106 107 108 109 110 111
+ 112 113 114 115 116 117 118 119
+ 120 121 122 123 124 125 126 127
+ 128 129 130 131 132 133 134 135
+ 136 137 138 139 140 141 142 143
+ 144 145 146 147 148 149 150 151
+ 152 153 154 155 156 157 158 159
+ 160 161 162 163 164 165 166 167
+ 168 169 170 171 172 173 174 175
+ 176 177 178 179 180 181 182 183
+ 184 185 186 187 188 189 190 191
+ 192 193 194 195 196 197 198 199
+ 200 201 202 203 204 205 206 207
+ 208 209 210 211 212 213 214 215
+ 216 217 218 219 220 221 222 223
+ 224 225 226 227 228 229 230 231
+ 232 233 234 235 236 237 238 239
+ 240 241 242 243 244 245 246 247
+ 248 249 250 251 252 253 254 255>;
+ default-brightness-level = <128>;
+ enable-gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>;
+ backlight-boot-off;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_en>;
+ pwms = <&pwm0 0 1000000 0>;
+ };
+
+ panel: panel {
+ compatible ="cnm,n116bgeea2","simple-panel";
+ status = "okay";
+ power-supply = <&vcc33_lcd>;
+ backlight = <&backlight>;
+ };
+
+ gpio_keys: gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_key_h>;
+ power {
+ label = "Power";
+ gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_POWER>;
+ debounce-interval = <100>;
+ gpio-key,wakeup;
+ };
+ };
+
+ gpio-restart {
+ compatible = "gpio-restart";
+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ap_warm_reset_h>;
+ priority = /bits/ 8 <200>;
+ };
+
+ sound {
+ compatible = "rockchip,rockchip-audio-max98090";
+ rockchip,model = "ROCKCHIP-I2S";
+ rockchip,i2s-controller = <&i2s>;
+ rockchip,audio-codec = <&max98090>;
+ rockchip,hp-det-gpios = <&gpio6 5 GPIO_ACTIVE_HIGH>;
+ rockchip,mic-det-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
+ rockchip,headset-codec = <&headsetcodec>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mic_det>, <&hp_det>;
+ };
+
+ vdd_logic: pwm-regulator {
+ compatible = "pwm-regulator";
+ pwms = <&pwm1 0 2000 0>;
+
+ voltage-table = <1350000 0>,
+ <1300000 10>,
+ <1250000 20>,
+ <1200000 31>,
+ <1150000 41>,
+ <1100000 52>,
+ <1050000 62>,
+ <1000000 72>,
+ < 950000 83>;
+
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-name = "vdd_logic";
+ regulator-ramp-delay = <4000>;
+ };
+
+ vcc33_sys: vcc33-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc33_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vccsys>;
+ };
+
+ vcc_5v: vcc-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_5v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vcc50_hdmi: vcc50-hdmi {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc50_hdmi";
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_5v>;
+ };
+
+ bt_regulator: bt-regulator {
+ /*
+ * On the module itself this is one of these (depending
+ * on the actual card pouplated):
+ * - BT_I2S_WS_BT_RFDISABLE_L
+ * - No connect
+ */
+
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_enable_l>;
+ regulator-name = "bt_regulator";
+ };
+
+ wifi_regulator: wifi-regulator {
+ /*
+ * On the module itself this is one of these (depending
+ * on the actual card populated):
+ * - SDIO_RESET_L_WL_REG_ON
+ * - PDN (power down when low)
+ */
+
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_h>;
+ regulator-name = "wifi_regulator";
+
+ /* Faux input supply. See bt_regulator description. */
+ vin-supply = <&bt_regulator>;
+ };
+
+ io-domains {
+ compatible = "rockchip,rk3288-io-voltage-domain";
+ rockchip,grf = <&grf>;
+
+ audio-supply = <&vcc18_codec>;
+ bb-supply = <&vcc33_io>;
+ dvp-supply = <&vcc_18>;
+ flash0-supply = <&vcc18_flashio>;
+ gpio1830-supply = <&vcc33_io>;
+ gpio30-supply = <&vcc33_io>;
+ lcdc-supply = <&vcc33_lcd>;
+ sdcard-supply = <&vccio_sd>;
+ wifi-supply = <&vcc18_wl>;
+ };
+};
+
+&cpu0 {
+ cpu0-supply = <&vdd_cpu>;
+};
+
+&dmc {
+ logic-supply = <&vdd_logic>;
+ rockchip,odt-disable-freq = <333000000>;
+ rockchip,dll-disable-freq = <333000000>;
+ rockchip,sr-enable-freq = <333000000>;
+ rockchip,pd-enable-freq = <666000000>;
+ rockchip,auto-self-refresh-cnt = <0>;
+ rockchip,auto-power-down-cnt = <64>;
+ rockchip,ddr-speed-bin = <21>;
+ rockchip,trcd = <10>;
+ rockchip,trp = <10>;
+ operating-points = <
+ /* KHz uV */
+ 200000 1050000
+ 333000 1100000
+ 533000 1150000
+ 666000 1200000
+ >;
+ rockchip,num-channels = <2>;
+ rockchip,pctl-timing = <0x29a 0xc8 0x1f8 0x42 0x4e 0x4 0xea 0xa
+ 0x5 0x0 0xa 0x7 0x19 0x24 0xa 0x7
+ 0x5 0xa 0x5 0x200 0x5 0x10 0x40 0x0
+ 0x1 0x7 0x7 0x4 0xc 0x43 0x100 0x0
+ 0x5 0x0>;
+ rockchip,phy-timing = <0x48f9aab4 0xea0910 0x1002c200
+ 0xa60 0x40 0x10 0x0>;
+ rockchip,sdram-channel = /bits/ 8 <0x1 0xa 0x3 0x2 0x1 0x0 0xf 0xf>;
+ rockchip,sdram-params = <0x30B25564 0x627 3 666000000 3 9 1>;
+};
+
+&efuse {
+ status = "okay";
+};
+
+&emmc {
+ broken-cd;
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ disable-wp;
+ non-removable;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8 &emmc_deassert_reset>;
+ status = "okay";
+};
+
+&sdio0 {
+ broken-cd;
+ bus-width = <4>;
+ cap-sd-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ cap-sdio-irq;
+ card-external-vcc-supply = <&wifi_regulator>;
+ clocks = <&cru HCLK_SDIO0>, <&cru SCLK_SDIO0>, <&cru SCLK_SDIO0_DRV>,
+ <&cru SCLK_SDIO0_SAMPLE>, <&rk808 RK808_CLKOUT1>;
+ clock-names = "biu", "ciu", "ciu_drv", "ciu_sample", "card_ext_clock";
+ keep-power-in-suspend;
+ non-removable;
+ num-slots = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio0_clk &sdio0_cmd &sdio0_bus4>;
+ status = "okay";
+ vmmc-supply = <&vcc33_sys>;
+ vqmmc-supply = <&vcc18_wl>;
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ card-detect-delay = <200>;
+ cd-gpios = <&gpio7 5 GPIO_ACTIVE_LOW>;
+ num-slots = <1>;
+ status = "okay";
+ vmmc-supply = <&vcc33_sd>;
+ vqmmc-supply = <&vccio_sd>;
+};
+
+&spi2 {
+ status = "okay";
+ u-boot,dm-pre-reloc;
+
+ spi_flash: spiflash@0 {
+ u-boot,dm-pre-reloc;
+ compatible = "spidev", "spi-flash";
+ spi-max-frequency = <20000000>; /* Reduce for Dediprog em100 pro */
+ reg = <0>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+ i2c-scl-falling-time-ns = <50>; /* 2.5ns measured */
+ i2c-scl-rising-time-ns = <100>; /* 45ns measured */
+
+ rk808: pmic@1b {
+ compatible = "rockchip,rk808";
+ clock-output-names = "xin32k", "wifibt_32kin";
+ interrupt-parent = <&gpio0>;
+ interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ reg = <0x1b>;
+ rockchip,system-power-controller;
+ wakeup-source;
+ #clock-cells = <1>;
+
+ vcc1-supply = <&vcc33_sys>;
+ vcc2-supply = <&vcc33_sys>;
+ vcc3-supply = <&vcc33_sys>;
+ vcc4-supply = <&vcc33_sys>;
+ vcc6-supply = <&vcc_5v>;
+ vcc7-supply = <&vcc33_sys>;
+ vcc8-supply = <&vcc33_sys>;
+ vcc9-supply = <&vcc_5v>;
+ vcc10-supply = <&vcc33_sys>;
+ vcc11-supply = <&vcc_5v>;
+ vcc12-supply = <&vcc_18>;
+
+ vddio-supply = <&vcc33_io>;
+
+ regulators {
+ vdd_cpu: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vdd_arm";
+ regulator-ramp-delay = <6001>;
+ regulator-suspend-mem-disabled;
+ };
+
+ vdd_gpu: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-name = "vdd_gpu";
+ regulator-ramp-delay = <6001>;
+ regulator-suspend-mem-disabled;
+ };
+
+ vcc135_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc135_ddr";
+ regulator-suspend-mem-enabled;
+ };
+
+ /*
+ * vcc_18 has several aliases. (vcc18_flashio and
+ * vcc18_wl). We'll add those aliases here just to
+ * make it easier to follow the schematic. The signals
+ * are actually hooked together and only separated for
+ * power measurement purposes).
+ */
+ vcc18_wl: vcc18_flashio: vcc_18: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_18";
+ regulator-suspend-mem-microvolt = <1800000>;
+ };
+
+ /*
+ * Note that both vcc33_io and vcc33_pmuio are always
+ * powered together. To simplify the logic in the dts
+ * we just refer to vcc33_io every time something is
+ * powered from vcc33_pmuio. In fact, on later boards
+ * (such as danger) they're the same net.
+ */
+ vcc33_io: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc33_io";
+ regulator-suspend-mem-microvolt = <3300000>;
+ };
+
+ vdd_10: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vdd_10";
+ regulator-suspend-mem-microvolt = <1000000>;
+ };
+
+ vccio_sd: LDO_REG4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd";
+ regulator-suspend-mem-disabled;
+ };
+
+ vcc33_sd: LDO_REG5 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc33_sd";
+ regulator-suspend-mem-disabled;
+ };
+
+ vcc18_codec: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc18_codec";
+ regulator-suspend-mem-disabled;
+ };
+
+ vdd10_lcd_pwren_h: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vdd10_lcd_pwren_h";
+ regulator-suspend-mem-disabled;
+ };
+
+ vcc33_lcd: SWITCH_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc33_lcd";
+ regulator-suspend-mem-disabled;
+ };
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+ i2c-scl-falling-time-ns = <50>; /* 2.5ns measured */
+ i2c-scl-rising-time-ns = <100>; /* 40ns measured */
+
+ tpm: tpm@20 {
+ compatible = "infineon,slb9645tt";
+ reg = <0x20>;
+ powered-while-suspended;
+ };
+};
+
+&i2c2 {
+ status = "okay";
+
+ /* 100kHz since 4.7k resistors don't rise fast enough */
+ clock-frequency = <100000>;
+ i2c-scl-falling-time-ns = <50>; /* 10ns measured */
+ i2c-scl-rising-time-ns = <800>; /* 600ns measured */
+
+ max98090: max98090@10 {
+ compatible = "maxim,max98090";
+ reg = <0x10>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&int_codec>;
+ };
+};
+
+&i2c3 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+ i2c-scl-falling-time-ns = <50>;
+ i2c-scl-rising-time-ns = <300>;
+};
+
+&i2c4 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+ i2c-scl-falling-time-ns = <50>; /* 11ns measured */
+ i2c-scl-rising-time-ns = <300>; /* 225ns measured */
+
+ headsetcodec: ts3a227e@3b {
+ compatible = "ti,ts3a227e";
+ reg = <0x3b>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts3a227e_int_l>;
+ ti,micbias = <7>; /* MICBIAS = 2.8V */
+ };
+};
+
+&i2c5 {
+ status = "okay";
+
+ clock-frequency = <100000>;
+ i2c-scl-falling-time-ns = <300>;
+ i2c-scl-rising-time-ns = <1000>;
+};
+
+&i2s {
+ status = "okay";
+ clock-names = "i2s_hclk", "i2s_clk", "i2s_clk_out";
+ clocks = <&cru HCLK_I2S0>, <&cru SCLK_I2S0>, <&cru SCLK_I2S0_OUT>;
+};
+
+&wdt {
+ status = "okay";
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+
+ /* Pins don't include flow control by default; add that in */
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+ /* We need to go faster than 24MHz, so adjust clock parents / rates */
+ assigned-clocks = <&cru SCLK_UART0>;
+ assigned-clock-rates = <48000000>;
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+ u-boot,dm-pre-reloc;
+ reg-shift = <2>;
+};
+
+&vopb {
+ status = "okay";
+};
+
+&vopb_mmu {
+ status = "okay";
+};
+
+&vopl {
+ status = "okay";
+};
+
+&vopl_mmu {
+ status = "okay";
+};
+
+&edp {
+ status = "okay";
+ rockchip,panel = <&panel>;
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_audio {
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+};
+
+&tsadc {
+ tsadc-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
+ tsadc-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
+ status = "okay";
+};
+
+&pinctrl {
+ u-boot,dm-pre-reloc;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <
+ /* Common for sleep and wake, but no owners */
+ &ddr0_retention
+ &ddrio_pwroff
+ &global_pwroff
+
+ /* Wake only */
+ &bt_dev_wake_awake
+ >;
+ pinctrl-1 = <
+ /* Common for sleep and wake, but no owners */
+ &ddr0_retention
+ &ddrio_pwroff
+ &global_pwroff
+
+ /* Sleep only */
+ &bt_dev_wake_sleep
+ >;
+
+ /* Add this for sdmmc pins to SD card */
+ pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
+ drive-strength = <8>;
+ };
+
+ pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
+ bias-pull-up;
+ drive-strength = <8>;
+ };
+
+ pcfg_output_high: pcfg-output-high {
+ output-high;
+ };
+
+ pcfg_output_low: pcfg-output-low {
+ output-low;
+ };
+
+ backlight {
+ bl_en: bl-en {
+ rockchip,pins = <7 2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ buttons {
+ pwr_key_h: pwr-key-h {
+ rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ codec {
+ hp_det: hp-det {
+ rockchip,pins = <6 5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ int_codec: int-codec {
+ rockchip,pins = <6 7 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ mic_det: mic-det {
+ rockchip,pins = <6 11 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ emmc {
+ /* Make sure eMMC is not in reset */
+ emmc_deassert_reset: emmc-deassert-reset {
+ rockchip,pins = <7 12 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ /*
+ * We run eMMC at max speed; bump up drive strength.
+ * We also have external pulls, so disable the internal ones.
+ */
+ emmc_clk: emmc-clk {
+ rockchip,pins = <3 18 RK_FUNC_2 &pcfg_pull_none_drv_8ma>;
+ };
+
+ emmc_cmd: emmc-cmd {
+ rockchip,pins = <3 16 RK_FUNC_2 &pcfg_pull_none_drv_8ma>;
+ };
+
+ emmc_bus8: emmc-bus8 {
+ rockchip,pins = <3 0 RK_FUNC_2 &pcfg_pull_none_drv_8ma>,
+ <3 1 RK_FUNC_2 &pcfg_pull_none_drv_8ma>,
+ <3 2 RK_FUNC_2 &pcfg_pull_none_drv_8ma>,
+ <3 3 RK_FUNC_2 &pcfg_pull_none_drv_8ma>,
+ <3 4 RK_FUNC_2 &pcfg_pull_none_drv_8ma>,
+ <3 5 RK_FUNC_2 &pcfg_pull_none_drv_8ma>,
+ <3 6 RK_FUNC_2 &pcfg_pull_none_drv_8ma>,
+ <3 7 RK_FUNC_2 &pcfg_pull_none_drv_8ma>;
+ };
+ };
+
+ headset {
+ ts3a227e_int_l: ts3a227e-int-l {
+ rockchip,pins = <0 3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ reboot {
+ ap_warm_reset_h: ap-warm-reset-h {
+ rockchip,pins = <RK_GPIO0 13 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdio0 {
+ wifi_enable_h: wifienable-h {
+ rockchip,pins = <4 28 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ /* NOTE: mislabelled on schematic; should be bt_enable_h */
+ bt_enable_l: bt-enable-l {
+ rockchip,pins = <4 29 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ /*
+ * We run sdio0 at max speed; bump up drive strength.
+ * We also have external pulls, so disable the internal ones.
+ */
+ sdio0_bus4: sdio0-bus4 {
+ rockchip,pins = <4 20 RK_FUNC_1 &pcfg_pull_none_drv_8ma>,
+ <4 21 RK_FUNC_1 &pcfg_pull_none_drv_8ma>,
+ <4 22 RK_FUNC_1 &pcfg_pull_none_drv_8ma>,
+ <4 23 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+ };
+
+ sdio0_cmd: sdio0-cmd {
+ rockchip,pins = <4 24 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+ };
+
+ sdio0_clk: sdio0-clk {
+ rockchip,pins = <4 25 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+ };
+
+ /*
+ * These pins are only present on very new veyron boards; on
+ * older boards bt_dev_wake is simply always high. Note that
+ * gpio4_26 is a NC on old veyron boards, so it doesn't hurt
+ * to map this pin everywhere
+ */
+ bt_dev_wake_sleep: bt-dev-wake-sleep {
+ rockchip,pins = <4 26 RK_FUNC_GPIO &pcfg_output_low>;
+ };
+
+ bt_dev_wake_awake: bt-dev-wake-awake {
+ rockchip,pins = <4 26 RK_FUNC_GPIO &pcfg_output_high>;
+ };
+ };
+
+ sdmmc {
+ /*
+ * We run sdmmc at max speed; bump up drive strength.
+ * We also have external pulls, so disable the internal ones.
+ */
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins = <6 16 RK_FUNC_1 &pcfg_pull_none_drv_8ma>,
+ <6 17 RK_FUNC_1 &pcfg_pull_none_drv_8ma>,
+ <6 18 RK_FUNC_1 &pcfg_pull_none_drv_8ma>,
+ <6 19 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+ };
+
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins = <6 20 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins = <6 21 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
+ };
+
+ /*
+ * Builtin CD line is hooked to ground to prevent JTAG at boot
+ * (and also to get the voltage rail correct). Make we
+ * configure gpio6_C6 as GPIO so dw_mmc builtin CD doesn't
+ * think there's a card inserted
+ */
+ sdmmc_cd_disabled: sdmmc-cd-disabled {
+ rockchip,pins = <6 22 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ /* This is where we actually hook up CD */
+ sdmmc_cd_gpio: sdmmc-cd-gpio {
+ rockchip,pins = <7 5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ tpm {
+ tpm_int_h: tpm-int-h {
+ rockchip,pins = <7 4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ write-protect {
+ fw_wp_ap: fw-wp-ap {
+ rockchip,pins = <7 6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&usbphy {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+ needs-reset-on-resume;
+};
+
+&usb_host1 {
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "host";
+ status = "okay";
+ assigned-clocks = <&cru SCLK_USBPHY480M_SRC>;
+ assigned-clock-parents = <&cru SCLK_OTGPHY0>;
+};
+
+&sdmmc {
+ u-boot,dm-pre-reloc;
+};
+
+&gpio3 {
+ u-boot,dm-pre-reloc;
+};
+
+&gpio8 {
+ u-boot,dm-pre-reloc;
+};
diff --git a/arch/arm/mach-rockchip/rk3288/Kconfig b/arch/arm/mach-rockchip/rk3288/Kconfig
index 7a77615..4d0f1b5 100644
--- a/arch/arm/mach-rockchip/rk3288/Kconfig
+++ b/arch/arm/mach-rockchip/rk3288/Kconfig
@@ -8,9 +8,19 @@
also includes on-board eMMC and 1GB of SDRAM. Expansion connectors
provide access to display pins, I2C, SPI, UART and GPIOs.
+config TARGET_CHROMEBOOK_JERRY
+ bool "Google/Rockchip Veyron-Jerry Chromebook"
+ help
+ Jerry is a RK3288-based clamshell device with 2 USB 3.0 ports,
+ HDMI, an 11.9 inch EDP display, micro-SD card, touchpad and
+ WiFi. It includes a Chrome OS EC (Cortex-M3) to provide access to
+ the keyboard and battery functions.
+
config SYS_SOC
default "rockchip"
+source "board/google/chromebook_jerry/Kconfig"
+
source "board/firefly/firefly-rk3288/Kconfig"
endif
diff --git a/board/google/chromebook_jerry/Kconfig b/board/google/chromebook_jerry/Kconfig
new file mode 100644
index 0000000..3640513
--- /dev/null
+++ b/board/google/chromebook_jerry/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_CHROMEBOOK_JERRY
+
+config SYS_BOARD
+ default "chromebook_jerry"
+
+config SYS_VENDOR
+ default "google"
+
+config SYS_CONFIG_NAME
+ default "chromebook_jerry"
+
+config BOARD_SPECIFIC_OPTIONS # dummy
+ def_bool y
+
+endif
diff --git a/board/google/chromebook_jerry/MAINTAINERS b/board/google/chromebook_jerry/MAINTAINERS
new file mode 100644
index 0000000..b01b6cd
--- /dev/null
+++ b/board/google/chromebook_jerry/MAINTAINERS
@@ -0,0 +1,6 @@
+CHROMEBOOK JERRY BOARD
+M: Simon Glass <sjg@chromium.org>
+S: Maintained
+F: board/google/chromebook_jerry/
+F: include/configs/chromebook_jerry.h
+F: configs/chromebook_jerry_defconfig
diff --git a/board/google/chromebook_jerry/Makefile b/board/google/chromebook_jerry/Makefile
new file mode 100644
index 0000000..d29a063
--- /dev/null
+++ b/board/google/chromebook_jerry/Makefile
@@ -0,0 +1,7 @@
+#
+# (C) Copyright 2015 Google, Inc
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += jerry.o
diff --git a/board/google/chromebook_jerry/jerry.c b/board/google/chromebook_jerry/jerry.c
new file mode 100644
index 0000000..5119e95
--- /dev/null
+++ b/board/google/chromebook_jerry/jerry.c
@@ -0,0 +1,7 @@
+/*
+ * (C) Copyright 2015 Google, Inc
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
diff --git a/board/google/common/Makefile b/board/google/common/Makefile
index b38bc14..2de2799 100644
--- a/board/google/common/Makefile
+++ b/board/google/common/Makefile
@@ -4,4 +4,4 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-y += early_init.o
+obj-$(CONFIG_X86) += early_init.o
diff --git a/configs/chromebook_jerry_defconfig b/configs/chromebook_jerry_defconfig
new file mode 100644
index 0000000..389dfd2
--- /dev/null
+++ b/configs/chromebook_jerry_defconfig
@@ -0,0 +1,43 @@
+CONFIG_ARM=y
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_ROCKCHIP_RK3288=y
+CONFIG_TARGET_CHROMEBOOK_JERRY=y
+CONFIG_DEFAULT_DEVICE_TREE="rk3288-jerry"
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_STACK_R_ADDR=0x80000
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_RESET=y
+CONFIG_LED=y
+CONFIG_SPL_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_BASE=0xff690000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_SIMPLE=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_SPL_PINCTRL_SIMPLE=y
+CONFIG_ROCKCHIP_PINCTRL=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_ACT8846=y
+CONFIG_DM_REGULATOR=y
+CONFIG_REGULATOR_ACT8846=y
+CONFIG_RAM=y
+CONFIG_SPL_RAM=y
+CONFIG_DM_MMC=y
+CONFIG_ROCKCHIP_DWMMC=y
+CONFIG_USE_PRIVATE_LIBGCC=y
+CONFIG_CMD_DHRYSTONE=y
+CONFIG_ERRNO_STR=y
diff --git a/include/configs/chromebook_jerry.h b/include/configs/chromebook_jerry.h
new file mode 100644
index 0000000..a22b123
--- /dev/null
+++ b/include/configs/chromebook_jerry.h
@@ -0,0 +1,16 @@
+/*
+ * (C) Copyright 2015 Google, Inc
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <configs/rk3288_common.h>
+
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_LOAD
+
+#endif