* Patches by Xianghua Xiao, 15 Oct 2003:
- Added Motorola CPU 8540/8560 support (cpu/85xx)
- Added Motorola MPC8540ADS board support (board/mpc8540ads)
- Added Motorola MPC8560ADS board support (board/mpc8560ads)
* Minor code cleanup
diff --git a/README b/README
index 617abb4..e3f4f9d 100644
--- a/README
+++ b/README
@@ -146,6 +146,7 @@
- cpu/mpc8xx Files specific to Motorola MPC8xx CPUs
- cpu/mpc824x Files specific to Motorola MPC824x CPUs
- cpu/mpc8260 Files specific to Motorola MPC8260 CPU
+- cpu/mpc85xx Files specific to Motorola MPC85xx CPUs
- cpu/ppc4xx Files specific to IBM 4xx CPUs
@@ -199,6 +200,10 @@
- board/mbx8xx Files specific to MBX boards
- board/mpc8260ads
Files specific to MPC8260ADS and PQ2FADS-ZU boards
+- board/mpc8540ads
+ Files specific to MPC8540ADS boards
+- board/mpc8560ads
+ Files specific to MPC8560ADS boards
- board/mpl/ Files specific to boards manufactured by MPL
- board/mpl/common Common files for MPL boards
- board/mpl/pip405 Files specific to PIP405 boards
@@ -210,7 +215,7 @@
- board/oxc Files specific to OXC boards
- board/omap1510inn
Files specific to OMAP 1510 Innovator boards
-- board/omap1610inn
+- board/omap1610inn
Files specific to OMAP 1610 Innovator boards
- board/pcippc2 Files specific to PCIPPC2/PCIPPC6 boards
- board/pm826 Files specific to PM826 boards
@@ -306,6 +311,7 @@
CONFIG_MPC823, CONFIG_MPC850, CONFIG_MPC855, CONFIG_MPC860
or CONFIG_MPC5xx
or CONFIG_MPC824X, CONFIG_MPC8260
+ or CONFIG_MPC85xx
or CONFIG_IOP480
or CONFIG_405GP
or CONFIG_405EP
@@ -356,7 +362,8 @@
CONFIG_IAD210, CONFIG_RPXlite, CONFIG_sbc8260,
CONFIG_EBONY, CONFIG_sacsng, CONFIG_FPS860L,
CONFIG_V37, CONFIG_ELPT860, CONFIG_CMI,
- CONFIG_NETVIA, CONFIG_RBC823, CONFIG_ZPC1900
+ CONFIG_NETVIA, CONFIG_RBC823, CONFIG_ZPC1900,
+ CONFIG_MPC8540ADS, CONFIG_MPC8560ADS
ARM based boards:
-----------------
@@ -591,7 +598,7 @@
CFG_CMD_DHCP DHCP support
CFG_CMD_DIAG * Diagnostics
CFG_CMD_DOC * Disk-On-Chip Support
- CFG_CMD_DTT Digital Therm and Thermostat
+ CFG_CMD_DTT Digital Therm and Thermostat
CFG_CMD_ECHO * echo arguments
CFG_CMD_EEPROM * EEPROM read/write support
CFG_CMD_ELF bootelf, bootvx
@@ -893,9 +900,9 @@
images is included. If not, only uncompressed and gzip
compressed images are supported.
- NOTE: the bzip2 algorithm requires a lot of RAM, so
- the malloc area (as defined by CFG_MALLOC_LEN) should
- be at least 4MB.
+ NOTE: the bzip2 algorithm requires a lot of RAM, so
+ the malloc area (as defined by CFG_MALLOC_LEN) should
+ be at least 4MB.
- Ethernet address:
CONFIG_ETHADDR
@@ -1757,13 +1764,13 @@
use the "saveenv" command to store a valid environment.
- CFG_FAULT_ECHO_LINK_DOWN:
- Echo the inverted Ethernet link state to the fault LED.
+ Echo the inverted Ethernet link state to the fault LED.
Note: If this option is active, then CFG_FAULT_MII_ADDR
also needs to be defined.
- CFG_FAULT_MII_ADDR:
- MII address of the PHY to check for the Ethernet link state.
+ MII address of the PHY to check for the Ethernet link state.
Low Level (hardware related) configuration options:
---------------------------------------------------
@@ -1774,9 +1781,9 @@
- CFG_DEFAULT_IMMR:
Default address of the IMMR after system reset.
- Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
- and RPXsuper) to be able to adjust the position of
- the IMMR register after a reset.
+ Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
+ and RPXsuper) to be able to adjust the position of
+ the IMMR register after a reset.
- Floppy Disk Support:
CFG_FDC_DRIVE_NUMBER
@@ -1950,7 +1957,8 @@
GEN860T_config EBONY_config FPS860L_config
ELPT860_config cmi_mpc5xx_config NETVIA_config
at91rm9200dk_config omap1510inn_config MPC8260ADS_config
- omap1610inn_config ZPC1900_config
+ omap1610inn_config ZPC1900_config MPC8540ADS_config
+ MPC8560ADS_config
Note: for some board special configuration names may exist; check if
additional information is available from the board vendor; for