arm: armada-xp: Add basic support for the maxBCM board
The maxBCM board is equipped with the Marvell Armada-XP MV78460 SoC. It
integrates an SPI NOR flash and an Marvell 88E6185 switch.
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/board/maxbcm/maxbcm.c b/board/maxbcm/maxbcm.c
new file mode 100644
index 0000000..7fc83ee
--- /dev/null
+++ b/board/maxbcm/maxbcm.c
@@ -0,0 +1,77 @@
+/*
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+#include <linux/mbus.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/* Base addresses for the external device chip selects */
+#define DEV_CS0_BASE 0xe0000000
+#define DEV_CS1_BASE 0xe1000000
+#define DEV_CS2_BASE 0xe2000000
+#define DEV_CS3_BASE 0xe3000000
+
+/* Needed for dynamic (board-specific) mbus configuration */
+extern struct mvebu_mbus_state mbus_state;
+
+int board_early_init_f(void)
+{
+ /*
+ * Don't configure MPP (pin multiplexing) and GPIO here,
+ * its already done in bin_hdr
+ */
+
+ /*
+ * Setup some board specific mbus address windows
+ */
+ mbus_dt_setup_win(&mbus_state, DEV_CS0_BASE, 16 << 20,
+ CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS0);
+ mbus_dt_setup_win(&mbus_state, DEV_CS1_BASE, 16 << 20,
+ CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS1);
+ mbus_dt_setup_win(&mbus_state, DEV_CS2_BASE, 16 << 20,
+ CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS2);
+ mbus_dt_setup_win(&mbus_state, DEV_CS3_BASE, 16 << 20,
+ CPU_TARGET_DEVICEBUS_BOOTROM_SPI, CPU_ATTR_DEV_CS3);
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: maxBCM\n");
+
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E6185 switch */
+void reset_phy(void)
+{
+ u16 devadr = CONFIG_PHY_BASE_ADDR;
+ char *name = "neta0";
+ u16 reg;
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* todo: fill this with the real setup / config code */
+
+ printf("88E6185 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */