serial: arm: Implement CONFIG_SERIAL_MULTI into netarm serial driver
Implement support for CONFIG_SERIAL_MULTI into netarm serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the netarm driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
diff --git a/common/serial.c b/common/serial.c
index 1ac8625..0c0712b 100644
--- a/common/serial.c
+++ b/common/serial.c
@@ -88,6 +88,7 @@
serial_initfunc(lpc2292_serial_initialize);
serial_initfunc(max3100_serial_initialize);
serial_initfunc(mxc_serial_initialize);
+serial_initfunc(netarm_serial_initialize);
void serial_register(struct serial_device *dev)
{
@@ -154,6 +155,7 @@
lpc2292_serial_initialize();
max3100_serial_initialize();
mxc_serial_initialize();
+ netarm_serial_initialize();
serial_assign(default_serial_console()->name);
}
diff --git a/drivers/serial/serial_netarm.c b/drivers/serial/serial_netarm.c
index d04790d..ff6612d 100644
--- a/drivers/serial/serial_netarm.c
+++ b/drivers/serial/serial_netarm.c
@@ -59,7 +59,7 @@
/*
* Setup both serial i/f with given baudrate
*/
-void serial_setbrg (void)
+static void netarm_serial_setbrg(void)
{
/* set 0 ... make sure pins are configured for serial */
#if !defined(CONFIG_NETARM_NS7520)
@@ -108,7 +108,7 @@
* Initialise the serial port with the given baudrate. The settings
* are always 8 data bits, no parity, 1 stop bit, no start bits.
*/
-int serial_init (void)
+static int netarm_serial_init(void)
{
serial_setbrg ();
return 0;
@@ -118,7 +118,7 @@
/*
* Output a single byte to the serial port.
*/
-void serial_putc (const char c)
+static void netarm_serial_putc(const char c)
{
volatile unsigned char *fifo;
@@ -135,7 +135,7 @@
* Test of a single byte from the serial port. Returns 1 on success, 0
* otherwise.
*/
-int serial_tstc(void)
+static int netarm_serial_tstc(void)
{
return serial_reg_ch1->status_a & NETARM_SER_STATA_RX_RDY;
}
@@ -144,7 +144,7 @@
* Read a single byte from the serial port. Returns 1 on success, 0
* otherwise.
*/
-int serial_getc (void)
+static int netarm_serial_getc(void)
{
unsigned int ch_uint;
volatile unsigned int *fifo;
@@ -182,9 +182,62 @@
return ch_uint & 0xff;
}
-void serial_puts (const char *s)
+static void netarm_serial_puts(const char *s)
{
while (*s) {
serial_putc (*s++);
}
}
+
+#ifdef CONFIG_SERIAL_MULTI
+static struct serial_device netarm_serial_drv = {
+ .name = "netarm_serial",
+ .start = netarm_serial_init,
+ .stop = NULL,
+ .setbrg = netarm_serial_setbrg,
+ .putc = netarm_serial_putc,
+ .puts = netarm_serial_puts,
+ .getc = netarm_serial_getc,
+ .tstc = netarm_serial_tstc,
+};
+
+void netarm_serial_initialize(void)
+{
+ serial_register(&netarm_serial_drv);
+}
+
+__weak struct serial_device *default_serial_console(void)
+{
+ return &netarm_serial_drv;
+}
+#else
+int serial_init(void)
+{
+ return netarm_serial_init();
+}
+
+void serial_setbrg(void)
+{
+ netarm_serial_setbrg();
+}
+
+void serial_putc(const char c)
+{
+ netarm_serial_putc(c);
+}
+
+void serial_puts(const char *s)
+{
+ netarm_serial_puts(s);
+}
+
+int serial_getc(void)
+{
+ return netarm_serial_getc();
+}
+
+int serial_tstc(void)
+{
+ return netarm_serial_tstc();
+}
+#endif