CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_SYS_TEXT_BASE=0x17800000
CONFIG_SYS_MALLOC_LEN=0x800000
CONFIG_SPL_GPIO=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x4000
CONFIG_ENV_OFFSET=0x100000
CONFIG_ENV_SECT_SIZE=0x10000
CONFIG_MX6Q=y
CONFIG_MX6_OCRAM_256KB=y
CONFIG_TARGET_PCM058=y
CONFIG_DM_GPIO=y
CONFIG_SPL_DM_SPI=y
CONFIG_DEFAULT_DEVICE_TREE="imx6q-phytec-mira-rdk-nand"
CONFIG_SPL_TEXT_BASE=0x00908000
CONFIG_SPL_MMC=y
CONFIG_SPL_SERIAL=y
CONFIG_SPL=y
CONFIG_ENV_OFFSET_REDUND=0x110000
CONFIG_SPL_LIBDISK_SUPPORT=y
CONFIG_SPL_SPI_FLASH_SUPPORT=y
CONFIG_SPL_SPI=y
CONFIG_CMD_HDMIDETECT=y
CONFIG_DISTRO_DEFAULTS=y
CONFIG_FIT=y
CONFIG_BOOTDELAY=3
CONFIG_BOOTCOMMAND="run mmcboot;run nandboot"
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_SPL_BOARD_INIT=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x18a
CONFIG_SPL_DMA=y
CONFIG_SPL_FS_EXT4=y
CONFIG_SPL_DM_SPI_FLASH=y
CONFIG_SPL_SPI_LOAD=y
CONFIG_SYS_SPI_U_BOOT_OFFS=0x31400
CONFIG_SPL_WATCHDOG=y
CONFIG_SPL_YMODEM_SUPPORT=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
CONFIG_CMD_NAND_TRIMFFS=y
# CONFIG_CMD_PINMUX is not set
CONFIG_CMD_CACHE=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_MTDPARTS=y
CONFIG_MTDIDS_DEFAULT="nand0=gpmi-nand"
CONFIG_MTDPARTS_DEFAULT="mtdparts=gpmi-nand:-(rootfs)"
CONFIG_CMD_UBI=y
# CONFIG_SPL_PARTITION_UUIDS is not set
CONFIG_SPL_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SPL_DM=y
CONFIG_BOUNCE_BUFFER=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_MXC=y
CONFIG_FSL_USDHC=y
CONFIG_MTD=y
CONFIG_DM_MTD=y
CONFIG_MTD_RAW_NAND=y
CONFIG_SYS_NAND_USE_FLASH_BBT=y
CONFIG_NAND_MXS=y
CONFIG_NAND_MXS_DT=y
CONFIG_SYS_NAND_ONFI_DETECTION=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SF_DEFAULT_SPEED=20000000
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
CONFIG_DM_ETH=y
CONFIG_DM_MDIO=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCONF=y
# CONFIG_PINCONF_RECURSIVE is not set
CONFIG_SPL_PINCTRL=y
CONFIG_SPL_PINCONF=y
# CONFIG_SPL_PINCONF_RECURSIVE is not set
CONFIG_PINCTRL_IMX6=y
CONFIG_DM_SERIAL=y
CONFIG_MXC_UART=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_MXC_SPI=y
# CONFIG_SPL_WDT is not set