Blackfin: unify cpu and boot modes
All of the duplicated code for Blackfin processors and boot modes have been
unified. After all, the core is the same for all processors, just the
peripheral set differs (which gets handled in the drivers).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
diff --git a/include/asm-blackfin/blackfin-config-post.h b/include/asm-blackfin/blackfin-config-post.h
index 4422225..6a1ffa1 100644
--- a/include/asm-blackfin/blackfin-config-post.h
+++ b/include/asm-blackfin/blackfin-config-post.h
@@ -14,9 +14,9 @@
# error Memory Map does not fit into configuration
#endif
-/* Sanity check BFIN_CPU */
-#ifndef BFIN_CPU
-# error BFIN_CPU: your board config needs to define this
+/* Sanity check CONFIG_BFIN_CPU */
+#ifndef CONFIG_BFIN_CPU
+# error CONFIG_BFIN_CPU: your board config needs to define this
#endif
/* Make sure the structure is properly aligned */
diff --git a/include/configs/bf533-ezkit.h b/include/configs/bf533-ezkit.h
index f2c8703..2f551ad 100644
--- a/include/configs/bf533-ezkit.h
+++ b/include/configs/bf533-ezkit.h
@@ -8,7 +8,6 @@
#include <asm/blackfin-config-pre.h>
#define CONFIG_BAUDRATE 57600
-#define CONFIG_STAMP 1
#define CONFIG_BOOTDELAY 5
#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
@@ -30,28 +29,15 @@
#define CONFIG_RTC_BFIN 1
#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
-/*
- * Boot Mode Set
- * Blackfin can support several boot modes
- */
-#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
-#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
-#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */
-/* Define the boot mode */
-#define BFIN_BOOT_MODE BF533_BYPASS_BOOT
-/* #define BFIN_BOOT_MODE BF533_SPI_BOOT */
-
#define CONFIG_PANIC_HANG 1
#define CONFIG_BFIN_CPU bf533-0.3
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
/* This sets the default state of the cache on U-Boot's boot */
#define CONFIG_ICACHE_ON
#define CONFIG_DCACHE_ON
-/* Define where the uboot will be loaded by on-chip boot rom */
-#define APP_ENTRY 0x00001000
-
/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ 27000000
/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
@@ -216,24 +202,14 @@
#define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
-/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
-/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
-#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
- ~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
-#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
- B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
-*/
-#define AMGCTLVAL 0xFF
-#define AMBCTL0VAL 0x7BB07BB0
-#define AMBCTL1VAL 0xFFC27BB0
+#define CONFIG_EBIU_SDRRC_VAL 0x398
+#define CONFIG_EBIU_SDGCTL_VAL 0x91118d
+#define CONFIG_EBIU_SDBCTL_VAL 0x13
-#define CONFIG_VDSP 1
+#define CONFIG_EBIU_AMGCTL_VAL 0xFF
+#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
+#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
-#ifdef CONFIG_VDSP
-#define ET_EXEC_VDSP 0x8
-#define SHT_STRTAB_VDSP 0x1
-#define ELFSHDRSIZE_VDSP 0x2C
-#define VDSP_ENTRY_ADDR 0xFFA00000
-#endif
+#include <asm/blackfin-config-post.h>
#endif
diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h
index 76dd2fa..66a0af6 100644
--- a/include/configs/bf533-stamp.h
+++ b/include/configs/bf533-stamp.h
@@ -7,38 +7,18 @@
#include <asm/blackfin-config-pre.h>
-#define CONFIG_STAMP 1
#define CONFIG_RTC_BFIN 1
-#define CONFIG_BF533 1
-/*
- * Boot Mode Set
- * Blackfin can support several boot modes
- */
-#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
-#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
-#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */
-/* Define the boot mode */
-#define BFIN_BOOT_MODE BF533_BYPASS_BOOT
-/* #define BFIN_BOOT_MODE BF533_SPI_BOOT */
#define CONFIG_PANIC_HANG 1
#define CONFIG_BFIN_CPU bf533-0.3
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
/* This sets the default state of the cache on U-Boot's boot */
#define CONFIG_ICACHE_ON
#define CONFIG_DCACHE_ON
-/* Define where the uboot will be loaded by on-chip boot rom */
-#define APP_ENTRY 0x00001000
-
/*
- * Stringize definitions - needed for environmental settings
- */
-#define STRINGIZE2(x) #x
-#define STRINGIZE(x) STRINGIZE2(x)
-
-/*
* Board settings
*/
#define CONFIG_DRIVER_SMC91111 1
@@ -61,8 +41,6 @@
*/
#define CONFIG_VIDEO 0
-#define CONFIG_VDSP 1
-
/*
* Clock settings
*/
@@ -88,10 +66,7 @@
/* Values can range from 2-65535 */
/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
#define CONFIG_SPI_BAUD 2
-
-#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
#define CONFIG_SPI_BAUD_INITBLOCK 4
-#endif
/*
* Network settings
@@ -126,14 +101,14 @@
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
-#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR 0x20004000
-#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE)
-#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
#define CFG_ENV_IS_IN_EEPROM 1
#define CFG_ENV_OFFSET 0x4000
#define CFG_ENV_HEADER (CFG_ENV_OFFSET + 0x12A) /* 0x12A is the length of LDR file header */
+#else
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR 0x20004000
+#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE)
#endif
#define CFG_ENV_SIZE 0x2000
@@ -165,11 +140,7 @@
#define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */
#define CONFIG_MEM_MT48LC64M4A2FB_7E 1
-#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
-#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#endif
#define CFG_SDRAM_BASE 0x00000000
@@ -207,14 +178,6 @@
#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
#endif
-#if (BFIN_BOOT_MODE == BF533_SPI_BOOT)
-#if (CONFIG_SCLK_HZ / (2*CONFIG_SPI_BAUD) > 20000000)
-#define CONFIG_SPI_FLASH_FAST_READ 1 /* Needed if SPI_CLK > 20 MHz */
-#else
-#undef CONFIG_SPI_FLASH_FAST_READ
-#endif
-#endif
-
/*
* Command settings
*/
@@ -222,26 +185,18 @@
#define CFG_LONGHELP 1
#define CONFIG_CMDLINE_EDITING 1
-#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
-#endif
/* configuration lookup from the BOOTP/DHCP server, */
/* but not try to load any image using TFTP */
#define CONFIG_BOOTDELAY 5
#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
-#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
#define CONFIG_BOOTCOMMAND "run ramboot"
-#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
-#define CONFIG_BOOTCOMMAND "eeprom read 0x1000000 0x100000 0x180000;icache on;dcache on;bootm 0x1000000"
-#endif
#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
-#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
-#if (CONFIG_DRIVER_SMC91111)
#define CONFIG_EXTRA_ENV_SETTINGS \
"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
@@ -257,29 +212,6 @@
"protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \
"cp.b $(loadaddr) 0x20000000 $(filesize)\0" \
""
-#else
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
- "flashboot=bootm 0x20100000\0" \
- "
-#endif
-
-#elif (BFIN_BOOT_MODE == BF533_SPI_BOOT)
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \
- "$(rootpath) console=ttyBF0,57600\0" \
- "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
- "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \
- "ramboot=tftpboot $(loadaddr) linux; " \
- "run ramargs;run addip;bootelf\0" \
- "nfsboot=tftpboot $(loadaddr) linux; " \
- "run nfsargs;run addip;bootelf\0" \
- "flashboot=bootm 0x20100000\0" \
- "update=tftpboot $(loadaddr) u-boot.ldr;" \
- "eeprom write $(loadaddr) 0x0 $(filesize);\0"\
- ""
-#endif
#ifdef CONFIG_SOFT_I2C
#if (!CONFIG_SOFT_I2C)
@@ -316,9 +248,7 @@
#define CONFIG_CMD_I2C
#endif
-#if (BFIN_BOOT_MODE == BF533_BYPASS_BOOT)
#define CONFIG_CMD_DHCP
-#endif
/*
@@ -428,25 +358,16 @@
/*
* FLASH organization and environment definitions
*/
-#define CFG_BOOTMAPSZ (8 << 20)/* Initial Memory map for Linux */
-/* 0xFF, 0xBBC3BBc3, 0x99B39983 */
-/*#define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
-#define AMBCTL0VAL (B1WAT_11 | B1RAT_11 | B1HT_3 | B1ST_4 | B1TT_4 | B1RDYPOL | \
- B1RDYEN | B0WAT_11 | B0RAT_11 | B0HT_3 | B0ST_4 | B0TT_4 | B0RDYPOL | B0RDYEN)
-#define AMBCTL1VAL (B3WAT_9 | B3RAT_9 | B3HT_2 | B3ST_3 | B3TT_4 | B3RDYPOL | \
- B3RDYEN | B2WAT_9 | B2RAT_9 | B2HT_2 | B2ST_4 | B2TT_4 | B2RDYPOL | B2RDYEN)
-*/
-#define AMGCTLVAL 0xFF
-#define AMBCTL0VAL 0xBBC3BBC3
-#define AMBCTL1VAL 0x99B39983
-#define CF_AMBCTL1VAL 0x99B3ffc2
+#define CONFIG_EBIU_SDRRC_VAL 0x268
+#define CONFIG_EBIU_SDGCTL_VAL 0x911109
+#define CONFIG_EBIU_SDBCTL_VAL 0x37
-#ifdef CONFIG_VDSP
-#define ET_EXEC_VDSP 0x8
-#define SHT_STRTAB_VDSP 0x1
-#define ELFSHDRSIZE_VDSP 0x2C
-#define VDSP_ENTRY_ADDR 0xFFA00000
-#endif
+#define CONFIG_EBIU_AMGCTL_VAL 0xFF
+#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3
+#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983
+#define CF_CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2
+
+#include <asm/blackfin-config-post.h>
#endif
diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h
index 0e189d4..39c7359 100644
--- a/include/configs/bf537-stamp.h
+++ b/include/configs/bf537-stamp.h
@@ -12,28 +12,15 @@
#define CONFIG_BAUDRATE 57600
/* Set default serial console for bf537 */
#define CONFIG_UART_CONSOLE 0
-#define CONFIG_BF537 1
#define CONFIG_BOOTDELAY 5
/* define CONFIG_BF537_STAMP_LEDCMD to enable LED command*/
/*#define CONFIG_BF537_STAMP_LEDCMD 1*/
-/*
- * Boot Mode Set
- * Blackfin can support several boot modes
- */
-#define BF537_BYPASS_BOOT 0x0011 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
-#define BF537_PARA_BOOT 0x0012 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
-#define BF537_SPI_MASTER_BOOT 0x0014 /* Bootmode 3: SPI master mode boot from SPI flash */
-#define BF537_SPI_SLAVE_BOOT 0x0015 /* Bootmode 4: SPI slave mode boot from SPI flash */
-#define BF537_TWI_MASTER_BOOT 0x0016 /* Bootmode 5: TWI master mode boot from EEPROM */
-#define BF537_TWI_SLAVE_BOOT 0x0017 /* Bootmode 6: TWI slave mode boot from EEPROM */
-#define BF537_UART_BOOT 0x0018 /* Bootmode 7: UART slave mdoe boot via UART host */
-/* Define the boot mode */
-#define BFIN_BOOT_MODE BF537_BYPASS_BOOT
-
#define CONFIG_PANIC_HANG 1
#define CONFIG_BFIN_CPU bf537-0.2
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
+
#define CONFIG_BFIN_MAC
/* This sets the default state of the cache on U-Boot's boot */
@@ -43,9 +30,6 @@
/* Define if want to do post memory test */
#undef CONFIG_POST_TEST
-/* Define where the uboot will be loaded by on-chip boot rom */
-#define APP_ENTRY 0x00001000
-
#define CONFIG_RTC_BFIN 1
#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
@@ -70,9 +54,7 @@
/* Values can range from 2-65535 */
/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */
#define CONFIG_SPI_BAUD 2
-#if (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
#define CONFIG_SPI_BAUD_INITBLOCK 4
-#endif
#if ( CONFIG_CLKIN_HALF == 0 )
#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT )
@@ -88,14 +70,6 @@
#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ
#endif
-#if (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
-#if (CONFIG_SCLK_HZ / (2*CONFIG_SPI_BAUD) > 20000000)
-#define CONFIG_SPI_FLASH_FAST_READ 1 /* Needed if SPI_CLK > 20 MHz */
-#else
-#undef CONFIG_SPI_FLASH_FAST_READ
-#endif
-#endif
-
#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */
#define CONFIG_MEM_ADD_WDTH 10 /* 8, 9, 10, 11 */
#define CONFIG_MEM_MT48LC32M8A2_75 1
@@ -131,7 +105,7 @@
#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
#define CONFIG_BOOTCOMMAND "run ramboot"
-#if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT) && defined(CONFIG_POST_TEST)
+#if defined(CONFIG_POST_TEST)
/* POST support */
#define CONFIG_POST ( CFG_POST_MEMORY | \
CFG_POST_UART | \
@@ -177,8 +151,6 @@
*/
#include <config_cmd_default.h>
-#if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT) || (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
-
#define CONFIG_CMD_ELF
#define CONFIG_CMD_I2C
#define CONFIG_CMD_CACHE
@@ -198,10 +170,6 @@
#define CONFIG_CMD_IDE
#endif
-#endif
-
-#if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT)
-
#define CONFIG_CMD_DHCP
#if defined(CONFIG_POST)
@@ -212,14 +180,10 @@
#define CONFIG_CMD_NAND
#endif
-#endif
-
#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600"
#define CONFIG_LOADADDR 0x1000000
-#if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT)
-#ifdef CONFIG_BFIN_MAC
#define CONFIG_EXTRA_ENV_SETTINGS \
"ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
@@ -236,36 +200,6 @@
"protect off 0x20000000 0x2007FFFF;" \
"erase 0x20000000 0x2007FFFF;cp.b 0x1000000 0x20000000 $(filesize)\0" \
""
-#else
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
- "flashboot=bootm 0x20100000\0" \
- ""
-#endif
-#elif (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
-#ifdef CONFIG_BFIN_MAC
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath) console=ttyBF0,57600\0"\
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):eth0:off\0" \
- "ramboot=tftpboot $(loadaddr) linux;" \
- "run ramargs;run addip;bootelf\0" \
- "nfsboot=tftpboot $(loadaddr) linux;" \
- "run nfsargs;run addip;bootelf\0" \
- "flashboot=bootm 0x20100000\0" \
- "update=tftpboot $(loadaddr) u-boot.ldr;" \
- "eeprom write $(loadaddr) 0x0 $(filesize);\0" \
- ""
-#else
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \
- "flashboot=bootm 0x20100000\0" \
- ""
-#endif
-#endif
#define CFG_PROMPT "bfin> " /* Monitor Command Prompt */
@@ -300,21 +234,18 @@
#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
-#if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT) || (BFIN_BOOT_MODE == BF537_UART_BOOT)
-/* for bf537-stamp, usrt boot mode still store env in flash */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR 0x20004000
-#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE)
-#elif (BFIN_BOOT_MODE == BF537_SPI_MASTER_BOOT)
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
#define CFG_ENV_IS_IN_EEPROM 1
#define CFG_ENV_OFFSET 0x4000
#define CFG_ENV_HEADER (CFG_ENV_OFFSET + 0x16e) /* 0x12A is the length of LDR file header */
+#else
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_ADDR 0x20004000
+#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE)
#endif
#define CFG_ENV_SIZE 0x2000
#define CFG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */
-/* #if (BFIN_BOOT_MODE == BF537_BYPASS_BOOT) */
#define ENV_IS_EMBEDDED
-/* #endif */
/* JFFS Partition offset set */
#define CFG_JFFS2_FIRST_BANK 0
@@ -383,6 +314,14 @@
#define CONFIG_TWICLK_KHZ 50
#endif
+#define CONFIG_EBIU_SDRRC_VAL 0x306
+#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
+#define CONFIG_EBIU_SDBCTL_VAL 0x25
+
+#define CONFIG_EBIU_AMGCTL_VAL 0xFF
+#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
+#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
+
#if defined CONFIG_SOFT_I2C
/*
* Software (bit-bang) I2C driver configuration
@@ -428,15 +367,6 @@
#define AMBCTL0VAL 0x7BB07BB0
#define AMBCTL1VAL 0xFFC27BB0
-#define CONFIG_VDSP 1
-
-#ifdef CONFIG_VDSP
-#define ET_EXEC_VDSP 0x8
-#define SHT_STRTAB_VDSP 0x1
-#define ELFSHDRSIZE_VDSP 0x2C
-#define VDSP_ENTRY_ADDR 0xFFA00000
-#endif
-
#if defined(CONFIG_BFIN_IDE)
#define CONFIG_DOS_PARTITION 1
@@ -492,4 +422,6 @@
#endif /*CONFIG_BFIN_IDE */
+#include <asm/blackfin-config-post.h>
+
#endif
diff --git a/include/configs/bf561-ezkit.h b/include/configs/bf561-ezkit.h
index c29555a..641548d 100644
--- a/include/configs/bf561-ezkit.h
+++ b/include/configs/bf561-ezkit.h
@@ -7,9 +7,6 @@
#include <asm/blackfin-config-pre.h>
-#define CONFIG_VDSP 1
-#define CONFIG_BF561 1
-
#define CFG_LONGHELP 1
#define CONFIG_CMDLINE_EDITING 1
#define CONFIG_BAUDRATE 57600
@@ -21,31 +18,13 @@
#define CONFIG_PANIC_HANG 1
#define CONFIG_BFIN_CPU bf561-0.3
-
-/*
-* Boot Mode Set
-* Blackfin can support several boot modes
-*/
-#define BF561_BYPASS_BOOT 0x21
-#define BF561_PARA_BOOT 0x22
-#define BF561_SPI_BOOT 0x24
-/* Define the boot mode */
-#define BFIN_BOOT_MODE BF561_BYPASS_BOOT
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
/* This sets the default state of the cache on U-Boot's boot */
#define CONFIG_ICACHE_ON
#define CONFIG_DCACHE_ON
-/* Define where the uboot will be loaded by on-chip boot rom */
-#define APP_ENTRY 0x00001000
-
/*
- * Stringize definitions - needed for environmental settings
- */
-#define STRINGIZE2(x) #x
-#define STRINGIZE(x) STRINGIZE2(x)
-
-/*
* Board settings
*/
#define CONFIG_DRIVER_SMC91111 1
@@ -242,17 +221,14 @@
/*
* FLASH organization and environment definitions
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_EBIU_SDRRC_VAL 0x306
+#define CONFIG_EBIU_SDGCTL_VAL 0x91114d
+#define CONFIG_EBIU_SDBCTL_VAL 0x15
-#define AMGCTLVAL 0x3F
-#define AMBCTL0VAL 0x7BB07BB0
-#define AMBCTL1VAL 0xFFC27BB0
+#define CONFIG_EBIU_AMGCTL_VAL 0x3F
+#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
+#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
-#ifdef CONFIG_VDSP
-#define ET_EXEC_VDSP 0x8
-#define SHT_STRTAB_VDSP 0x1
-#define ELFSHDRSIZE_VDSP 0x2C
-#define VDSP_ENTRY_ADDR 0xFFA00000
-#endif
+#include <asm/blackfin-config-post.h>
#endif /* __CONFIG_EZKIT561_H__ */