diff --git a/src/arm64/qcom/qrb4210-rb2.dts b/src/arm64/qcom/qrb4210-rb2.dts
index a7278a9..7c19f87 100644
--- a/src/arm64/qcom/qrb4210-rb2.dts
+++ b/src/arm64/qcom/qrb4210-rb2.dts
@@ -15,6 +15,7 @@
 
 	aliases {
 		serial0 = &uart4;
+		serial1 = &uart3;
 	};
 
 	chosen {
@@ -280,6 +281,12 @@
 	status = "okay";
 };
 
+&remoteproc_mpss {
+	firmware-name = "qcom/qrb4210/modem.mbn";
+
+	status = "okay";
+};
+
 &rpm_requests {
 	regulators {
 		compatible = "qcom,rpm-pm6125-regulators";
@@ -346,13 +353,14 @@
 		};
 
 		vreg_l8a_0p664: l8 {
-			regulator-min-microvolt = <400000>;
-			regulator-max-microvolt = <728000>;
+			regulator-min-microvolt = <640000>;
+			regulator-max-microvolt = <640000>;
 		};
 
 		vreg_l9a_1p8: l9 {
 			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <2000000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-allow-set-load;
 		};
 
 		vreg_l10a_1p8: l10 {
@@ -389,11 +397,13 @@
 		vreg_l16a_1p3: l16 {
 			regulator-min-microvolt = <1704000>;
 			regulator-max-microvolt = <1904000>;
+			regulator-allow-set-load;
 		};
 
 		vreg_l17a_1p3: l17 {
 			regulator-min-microvolt = <1152000>;
 			regulator-max-microvolt = <1384000>;
+			regulator-allow-set-load;
 		};
 
 		vreg_l18a_1p232: l18 {
@@ -424,8 +434,9 @@
 		};
 
 		vreg_l23a_3p3: l23 {
-			regulator-min-microvolt = <3200000>;
-			regulator-max-microvolt = <3400000>;
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-allow-set-load;
 		};
 
 		vreg_l24a_2p96: l24 {
@@ -487,6 +498,66 @@
 			       <56 3>, <61 2>, <64 1>,
 			       <68 1>, <72 8>, <96 1>;
 
+	uart3_default: uart3-default-state {
+		cts-pins {
+			pins = "gpio8";
+			function = "qup3";
+			drive-strength = <2>;
+			bias-bus-hold;
+		};
+
+		rts-pins {
+			pins = "gpio9";
+			function = "qup3";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		tx-pins {
+			pins = "gpio10";
+			function = "qup3";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		rx-pins {
+			pins = "gpio11";
+			function = "qup3";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	uart3_sleep: uart3-sleep-state {
+		cts-pins {
+			pins = "gpio8";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-bus-hold;
+		};
+
+		rts-pins {
+			pins = "gpio9";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		tx-pins {
+			pins = "gpio10";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		rx-pins {
+			pins = "gpio11";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
 	lt9611_rst_pin: lt9611-rst-state {
 		pins = "gpio41";
 		function = "gpio";
@@ -508,6 +579,26 @@
 	};
 };
 
+&uart3 {
+	interrupts-extended = <&intc GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+			      <&tlmm 11 IRQ_TYPE_LEVEL_HIGH>;
+	pinctrl-0 = <&uart3_default>;
+	pinctrl-1 = <&uart3_sleep>;
+	pinctrl-names = "default", "sleep";
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3988-bt";
+
+		vddio-supply = <&vreg_l9a_1p8>;
+		vddxo-supply = <&vreg_l16a_1p3>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l23a_3p3>;
+		enable-gpios = <&tlmm 87 GPIO_ACTIVE_HIGH>;
+		max-speed = <3200000>;
+	};
+};
+
 &uart4 {
 	status = "okay";
 };
@@ -518,7 +609,6 @@
 
 &usb_dwc3 {
 	maximum-speed = "super-speed";
-	dr_mode = "peripheral";
 };
 
 &usb_hsphy {
@@ -536,6 +626,16 @@
 	status = "okay";
 };
 
+&wifi {
+	vdd-0.8-cx-mx-supply = <&vreg_l8a_0p664>;
+	vdd-1.8-xo-supply = <&vreg_l16a_1p3>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l23a_3p3>;
+	qcom,ath10k-calibration-variant = "Thundercomm_RB2";
+
+	status = "okay";
+};
+
 &xo_board {
 	clock-frequency = <19200000>;
 };