diff --git a/src/arm/nxp/imx/imx1-ads.dts b/src/arm/nxp/imx/imx1-ads.dts
index 5833fb6..2c817c4 100644
--- a/src/arm/nxp/imx/imx1-ads.dts
+++ b/src/arm/nxp/imx/imx1-ads.dts
@@ -65,7 +65,7 @@
 	pinctrl-0 = <&pinctrl_weim>;
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x00000000 0x02000000>;
 		bank-width = <4>;
diff --git a/src/arm/nxp/imx/imx1-apf9328.dts b/src/arm/nxp/imx/imx1-apf9328.dts
index 1f11e95..e66eef8 100644
--- a/src/arm/nxp/imx/imx1-apf9328.dts
+++ b/src/arm/nxp/imx/imx1-apf9328.dts
@@ -45,7 +45,7 @@
 	pinctrl-0 = <&pinctrl_weim>;
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x00000000 0x02000000>;
 		bank-width = <2>;
diff --git a/src/arm/nxp/imx/imx1.dtsi b/src/arm/nxp/imx/imx1.dtsi
index e312f1e..1ac1096 100644
--- a/src/arm/nxp/imx/imx1.dtsi
+++ b/src/arm/nxp/imx/imx1.dtsi
@@ -68,7 +68,7 @@
 		interrupt-parent = <&aitc>;
 		ranges;
 
-		aipi@200000 {
+		bus@200000 {
 			compatible = "fsl,aipi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -155,7 +155,7 @@
 			};
 		};
 
-		aipi@210000 {
+		bus@210000 {
 			compatible = "fsl,aipi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -268,9 +268,12 @@
 			status = "disabled";
 		};
 
-		esram: esram@300000 {
+		esram: sram@300000 {
 			compatible = "mmio-sram";
 			reg = <0x00300000 0x20000>;
+			ranges = <0 0x00300000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 	};
 };
diff --git a/src/arm/nxp/imx/imx25-eukrea-cpuimx25.dtsi b/src/arm/nxp/imx/imx25-eukrea-cpuimx25.dtsi
index 0703f62..93a6e4e 100644
--- a/src/arm/nxp/imx/imx25-eukrea-cpuimx25.dtsi
+++ b/src/arm/nxp/imx/imx25-eukrea-cpuimx25.dtsi
@@ -27,7 +27,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pcf8563@51 {
+	rtc@51 {
 		compatible = "nxp,pcf8563";
 		reg = <0x51>;
 	};
diff --git a/src/arm/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dts b/src/arm/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dts
index fc8a502..6cddb2c 100644
--- a/src/arm/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dts
+++ b/src/arm/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-cmo-qvga.dts
@@ -16,7 +16,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&qvga_timings>;
-			qvga_timings: 320x240 {
+			qvga_timings: timing0 {
 				clock-frequency = <6500000>;
 				hactive = <320>;
 				vactive = <240>;
diff --git a/src/arm/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dts b/src/arm/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dts
index 80a7f96..64b2ffa 100644
--- a/src/arm/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dts
+++ b/src/arm/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-svga.dts
@@ -16,7 +16,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&dvi_svga_timings>;
-			dvi_svga_timings: 800x600 {
+			dvi_svga_timings: timing0 {
 				clock-frequency = <40000000>;
 				hactive = <800>;
 				vactive = <600>;
diff --git a/src/arm/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dts b/src/arm/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dts
index 24027a1..fb074bf 100644
--- a/src/arm/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dts
+++ b/src/arm/nxp/imx/imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dts
@@ -16,7 +16,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&dvi_vga_timings>;
-			dvi_vga_timings: 640x480 {
+			dvi_vga_timings: timing0 {
 				clock-frequency = <31250000>;
 				hactive = <640>;
 				vactive = <480>;
diff --git a/src/arm/nxp/imx/imx25-pdk.dts b/src/arm/nxp/imx/imx25-pdk.dts
index 04f4b12..dd176fb 100644
--- a/src/arm/nxp/imx/imx25-pdk.dts
+++ b/src/arm/nxp/imx/imx25-pdk.dts
@@ -68,7 +68,7 @@
 		bus-width = <18>;
 		display-timings {
 			native-mode = <&wvga_timings>;
-			wvga_timings: 640x480 {
+			wvga_timings: timing0 {
 				hactive = <640>;
 				vactive = <480>;
 				hback-porch = <45>;
@@ -122,6 +122,7 @@
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks 129>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
diff --git a/src/arm/nxp/imx/imx25.dtsi b/src/arm/nxp/imx/imx25.dtsi
index 534c70b..9cfff21 100644
--- a/src/arm/nxp/imx/imx25.dtsi
+++ b/src/arm/nxp/imx/imx25.dtsi
@@ -68,6 +68,16 @@
 		};
 	};
 
+	usbphy0: usb-phy0 {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+	};
+
+	usbphy1: usb-phy1 {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+	};
+
 	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -93,7 +103,7 @@
 				compatible = "fsl,imx25-i2c", "fsl,imx21-i2c";
 				reg = <0x43f80000 0x4000>;
 				clocks = <&clks 48>;
-				clock-names = "";
+				clock-names = "ipg";
 				interrupts = <3>;
 				status = "disabled";
 			};
@@ -104,7 +114,7 @@
 				compatible = "fsl,imx25-i2c", "fsl,imx21-i2c";
 				reg = <0x43f84000 0x4000>;
 				clocks = <&clks 48>;
-				clock-names = "";
+				clock-names = "ipg";
 				interrupts = <10>;
 				status = "disabled";
 			};
@@ -151,7 +161,7 @@
 				compatible = "fsl,imx25-i2c", "fsl,imx21-i2c";
 				reg = <0x43f98000 0x4000>;
 				clocks = <&clks 48>;
-				clock-names = "";
+				clock-names = "ipg";
 				interrupts = <4>;
 				status = "disabled";
 			};
@@ -178,12 +188,9 @@
 			};
 
 			kpp: kpp@43fa8000 {
-				#address-cells = <1>;
-				#size-cells = <0>;
 				compatible = "fsl,imx25-kpp", "fsl,imx21-kpp";
 				reg = <0x43fa8000 0x4000>;
 				clocks = <&clks 102>;
-				clock-names = "";
 				interrupts = <24>;
 				status = "disabled";
 			};
@@ -542,7 +549,7 @@
 			};
 
 			iim: efuse@53ff0000 {
-				compatible = "fsl,imx25-iim", "fsl,imx27-iim";
+				compatible = "fsl,imx25-iim";
 				reg = <0x53ff0000 0x4000>;
 				interrupts = <19>;
 				clocks = <&clks 99>;
@@ -597,7 +604,7 @@
 			#size-cells = <1>;
 		};
 
-		emi@80000000 {
+		bus@80000000 {
 			compatible = "fsl,emi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -617,22 +624,4 @@
 			};
 		};
 	};
-
-	usbphy {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		usbphy0: usb-phy@0 {
-			reg = <0>;
-			compatible = "usb-nop-xceiv";
-			#phy-cells = <0>;
-		};
-
-		usbphy1: usb-phy@1 {
-			reg = <1>;
-			compatible = "usb-nop-xceiv";
-			#phy-cells = <0>;
-		};
-	};
 };
diff --git a/src/arm/nxp/imx/imx27-apf27dev.dts b/src/arm/nxp/imx/imx27-apf27dev.dts
index a21f1f7..849306c 100644
--- a/src/arm/nxp/imx/imx27-apf27dev.dts
+++ b/src/arm/nxp/imx/imx27-apf27dev.dts
@@ -16,7 +16,7 @@
 		fsl,pcr = <0xfae80083>;	/* non-standard but required */
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 800x480 {
+			timing0: timing0 {
 				clock-frequency = <33000033>;
 				hactive = <800>;
 				vactive = <480>;
@@ -47,7 +47,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_leds>;
 
-		user {
+		led-user {
 			label = "Heartbeat";
 			gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
diff --git a/src/arm/nxp/imx/imx27-eukrea-cpuimx27.dtsi b/src/arm/nxp/imx/imx27-eukrea-cpuimx27.dtsi
index 74110bb..c7e9235 100644
--- a/src/arm/nxp/imx/imx27-eukrea-cpuimx27.dtsi
+++ b/src/arm/nxp/imx/imx27-eukrea-cpuimx27.dtsi
@@ -33,7 +33,7 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pcf8563@51 {
+	rtc@51 {
 		compatible = "nxp,pcf8563";
 		reg = <0x51>;
 	};
@@ -90,7 +90,7 @@
 &weim {
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "cfi-flash";
diff --git a/src/arm/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dts b/src/arm/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dts
index 145e459..d787936 100644
--- a/src/arm/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dts
+++ b/src/arm/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dts
@@ -16,7 +16,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 320x240 {
+			timing0: timing0 {
 				clock-frequency = <6500000>;
 				hactive = <320>;
 				vactive = <240>;
diff --git a/src/arm/nxp/imx/imx27-pdk.dts b/src/arm/nxp/imx/imx27-pdk.dts
index 35123b7..21d4369 100644
--- a/src/arm/nxp/imx/imx27-pdk.dts
+++ b/src/arm/nxp/imx/imx27-pdk.dts
@@ -14,18 +14,12 @@
 		reg = <0xa0000000 0x08000000>;
 	};
 
-	usbphy {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		usbphy0: usbphy@0 {
-			compatible = "usb-nop-xceiv";
-			reg = <0>;
-			clocks = <&clks IMX27_CLK_DUMMY>;
-			clock-names = "main_clk";
-			#phy-cells = <0>;
-		};
+	usbphy0: usbphy {
+		compatible = "usb-nop-xceiv";
+		clocks = <&clks IMX27_CLK_DUMMY>;
+		clock-names = "main_clk";
+		#phy-cells = <0>;
 	};
 };
 
diff --git a/src/arm/nxp/imx/imx27-phytec-phycard-s-rdk.dts b/src/arm/nxp/imx/imx27-phytec-phycard-s-rdk.dts
index 25442eb..27c93b9 100644
--- a/src/arm/nxp/imx/imx27-phytec-phycard-s-rdk.dts
+++ b/src/arm/nxp/imx/imx27-phytec-phycard-s-rdk.dts
@@ -19,7 +19,7 @@
 		fsl,pcr = <0xf0c88080>;	/* non-standard but required */
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 640x480 {
+			timing0: timing0 {
 				hactive = <640>;
 				vactive = <480>;
 				hback-porch = <112>;
diff --git a/src/arm/nxp/imx/imx27-phytec-phycore-rdk.dts b/src/arm/nxp/imx/imx27-phytec-phycore-rdk.dts
index 7f0cd4d..b8048e1 100644
--- a/src/arm/nxp/imx/imx27-phytec-phycore-rdk.dts
+++ b/src/arm/nxp/imx/imx27-phytec-phycore-rdk.dts
@@ -19,7 +19,7 @@
 
 		display-timings {
 			native-mode = <&timing0>;
-			timing0: 240x320 {
+			timing0: timing0 {
 				clock-frequency = <5500000>;
 				hactive = <240>;
 				vactive = <320>;
@@ -48,15 +48,12 @@
 		regulator-always-on;
 	};
 
-	usbphy {
-		usbphy2: usbphy@2 {
-			compatible = "usb-nop-xceiv";
-			reg = <2>;
-			vcc-supply = <&reg_5v0>;
-			clocks = <&clks IMX27_CLK_DUMMY>;
-			clock-names = "main_clk";
-			#phy-cells = <0>;
-		};
+	usbphy2: usbphy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&reg_5v0>;
+		clocks = <&clks IMX27_CLK_DUMMY>;
+		clock-names = "main_clk";
+		#phy-cells = <0>;
 	};
 };
 
diff --git a/src/arm/nxp/imx/imx27-phytec-phycore-som.dtsi b/src/arm/nxp/imx/imx27-phytec-phycore-som.dtsi
index 7b2ea4c..e958d72 100644
--- a/src/arm/nxp/imx/imx27-phytec-phycore-som.dtsi
+++ b/src/arm/nxp/imx/imx27-phytec-phycore-som.dtsi
@@ -29,19 +29,13 @@
 		regulator-max-microvolt = <5000000>;
 	};
 
-	usbphy {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		usbphy0: usbphy@0 {
-			compatible = "usb-nop-xceiv";
-			reg = <0>;
-			vcc-supply = <&sw3_reg>;
-			clocks = <&clks IMX27_CLK_DUMMY>;
-			clock-names = "main_clk";
-			#phy-cells = <0>;
-		};
+	usbphy0: usbphy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&sw3_reg>;
+		clocks = <&clks IMX27_CLK_DUMMY>;
+		clock-names = "main_clk";
+		#phy-cells = <0>;
 	};
 };
 
@@ -49,12 +43,12 @@
 	status = "okay";
 
 	/* SSI0 <=> PINS_4 (MC13783 Audio) */
-	ssi0 {
+	mux-ssi0 {
 		fsl,audmux-port = <0>;
 		fsl,port-config = <0xcb205000>;
 	};
 
-	pins4 {
+	mux-pins4 {
 		fsl,audmux-port = <2>;
 		fsl,port-config = <0x00001000>;
 	};
@@ -186,7 +180,7 @@
 		reg = <0x52>;
 	};
 
-	pcf8563@51 {
+	rtc@51 {
 		compatible = "nxp,pcf8563";
 		reg = <0x51>;
 	};
@@ -314,7 +308,7 @@
 &weim {
 	status = "okay";
 
-	nor: nor@0,0 {
+	nor: flash@0,0 {
 		compatible = "cfi-flash";
 		reg = <0 0x00000000 0x02000000>;
 		bank-width = <2>;
diff --git a/src/arm/nxp/imx/imx27.dtsi b/src/arm/nxp/imx/imx27.dtsi
index faba12e..ec47269 100644
--- a/src/arm/nxp/imx/imx27.dtsi
+++ b/src/arm/nxp/imx/imx27.dtsi
@@ -81,7 +81,7 @@
 		interrupt-parent = <&aitc>;
 		ranges;
 
-		aipi1: aipi@10000000 { /* AIPI1 */
+		aipi1: bus@10000000 { /* AIPI1 */
 			compatible = "fsl,aipi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -453,7 +453,7 @@
 			};
 		};
 
-		aipi2: aipi@10020000 { /* AIPI2 */
+		aipi2: bus@10020000 { /* AIPI2 */
 			compatible = "fsl,aipi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -588,6 +588,9 @@
 		iram: sram@ffff4c00 {
 			compatible = "mmio-sram";
 			reg = <0xffff4c00 0xb400>;
+			ranges = <0 0xffff4c00 0xb400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 	};
 };
diff --git a/src/arm/nxp/imx/imx53-cx9020.dts b/src/arm/nxp/imx/imx53-cx9020.dts
index 055d23a..0814f56 100644
--- a/src/arm/nxp/imx/imx53-cx9020.dts
+++ b/src/arm/nxp/imx/imx53-cx9020.dts
@@ -22,7 +22,7 @@
 	};
 
 	display-0 {
-		#address-cells =<1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "fsl,imx-parallel-display";
 		interface-pix-fmt = "rgb24";
diff --git a/src/arm/nxp/imx/imx6dl-b105pv2.dts b/src/arm/nxp/imx/imx6dl-b105pv2.dts
index 7d4ae11..63cdf24 100644
--- a/src/arm/nxp/imx/imx6dl-b105pv2.dts
+++ b/src/arm/nxp/imx/imx6dl-b105pv2.dts
@@ -22,7 +22,7 @@
 		compatible = "ilitek,ili251x";
 		reg = <0x41>;
 		pinctrl-names = "default";
-		pinctrl-0 =<&pinctrl_q7_gpio0>;
+		pinctrl-0 = <&pinctrl_q7_gpio0>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
 		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_LOW>;
diff --git a/src/arm/nxp/imx/imx6dl-b105v2.dts b/src/arm/nxp/imx/imx6dl-b105v2.dts
index 9c5938e..2e75d70 100644
--- a/src/arm/nxp/imx/imx6dl-b105v2.dts
+++ b/src/arm/nxp/imx/imx6dl-b105v2.dts
@@ -22,7 +22,7 @@
 		compatible = "ilitek,ili251x";
 		reg = <0x41>;
 		pinctrl-names = "default";
-		pinctrl-0 =<&pinctrl_q7_gpio0>;
+		pinctrl-0 = <&pinctrl_q7_gpio0>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
 		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_LOW>;
diff --git a/src/arm/nxp/imx/imx6dl-b125pv2.dts b/src/arm/nxp/imx/imx6dl-b125pv2.dts
index 01df7cf..94625d5 100644
--- a/src/arm/nxp/imx/imx6dl-b125pv2.dts
+++ b/src/arm/nxp/imx/imx6dl-b125pv2.dts
@@ -22,7 +22,7 @@
 		compatible = "eeti,exc80h60";
 		reg = <0x2a>;
 		pinctrl-names = "default";
-		pinctrl-0 =<&pinctrl_q7_gpio0>;
+		pinctrl-0 = <&pinctrl_q7_gpio0>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_HIGH>;
diff --git a/src/arm/nxp/imx/imx6dl-b125v2.dts b/src/arm/nxp/imx/imx6dl-b125v2.dts
index a015453..b3cfa81 100644
--- a/src/arm/nxp/imx/imx6dl-b125v2.dts
+++ b/src/arm/nxp/imx/imx6dl-b125v2.dts
@@ -22,7 +22,7 @@
 		compatible = "eeti,exc80h60";
 		reg = <0x2a>;
 		pinctrl-names = "default";
-		pinctrl-0 =<&pinctrl_q7_gpio0>;
+		pinctrl-0 = <&pinctrl_q7_gpio0>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		reset-gpios = <&tca6424a 21 GPIO_ACTIVE_HIGH>;
diff --git a/src/arm/nxp/imx/imx6dl-b155v2.dts b/src/arm/nxp/imx/imx6dl-b155v2.dts
index b71ee6b..7edc788 100644
--- a/src/arm/nxp/imx/imx6dl-b155v2.dts
+++ b/src/arm/nxp/imx/imx6dl-b155v2.dts
@@ -22,7 +22,7 @@
 		compatible = "eeti,exc80h84";
 		reg = <0x2a>;
 		pinctrl-names = "default";
-		pinctrl-0 =<&pinctrl_q7_gpio0>;
+		pinctrl-0 = <&pinctrl_q7_gpio0>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		touchscreen-inverted-x;
diff --git a/src/arm/nxp/imx/imx6q-apalis-ixora-v1.2.dts b/src/arm/nxp/imx/imx6q-apalis-ixora-v1.2.dts
index 717decd..3ac7a45 100644
--- a/src/arm/nxp/imx/imx6q-apalis-ixora-v1.2.dts
+++ b/src/arm/nxp/imx/imx6q-apalis-ixora-v1.2.dts
@@ -76,6 +76,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_enable_can1_power>;
 		regulator-name = "can1_supply";
+		startup-delay-us = <1000>;
 	};
 
 	reg_can2_supply: regulator-can2-supply {
@@ -85,6 +86,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_enable_can2_power>;
 		regulator-name = "can2_supply";
+		startup-delay-us = <1000>;
 	};
 };
 
diff --git a/src/arm/nxp/imx/imx6q-b850v3.dts b/src/arm/nxp/imx/imx6q-b850v3.dts
index db8c332..cad112e 100644
--- a/src/arm/nxp/imx/imx6q-b850v3.dts
+++ b/src/arm/nxp/imx/imx6q-b850v3.dts
@@ -227,7 +227,6 @@
 
 		#address-cells = <3>;
 		#size-cells = <2>;
-		#interrupt-cells = <1>;
 
 		bridge@2,1 {
 			compatible = "pci10b5,8605";
@@ -235,7 +234,6 @@
 
 			#address-cells = <3>;
 			#size-cells = <2>;
-			#interrupt-cells = <1>;
 
 			/* Intel Corporation I210 Gigabit Network Connection */
 			ethernet@3,0 {
@@ -250,7 +248,6 @@
 
 			#address-cells = <3>;
 			#size-cells = <2>;
-			#interrupt-cells = <1>;
 
 			/* Intel Corporation I210 Gigabit Network Connection */
 			switch_nic: ethernet@4,0 {
diff --git a/src/arm/nxp/imx/imx6q-bx50v3.dtsi b/src/arm/nxp/imx/imx6q-bx50v3.dtsi
index 99f4f6a..c1ae7c4 100644
--- a/src/arm/nxp/imx/imx6q-bx50v3.dtsi
+++ b/src/arm/nxp/imx/imx6q-bx50v3.dtsi
@@ -245,6 +245,7 @@
 				reg = <0x74>;
 				gpio-controller;
 				#gpio-cells = <2>;
+				#interrupt-cells = <2>;
 				interrupt-controller;
 				interrupt-parent = <&gpio2>;
 				interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
@@ -390,7 +391,6 @@
 
 		#address-cells = <3>;
 		#size-cells = <2>;
-		#interrupt-cells = <1>;
 	};
 };
 
diff --git a/src/arm/nxp/imx/imx6q-var-mx6customboard.dts b/src/arm/nxp/imx/imx6q-var-mx6customboard.dts
index 6f9d094..18a6208 100644
--- a/src/arm/nxp/imx/imx6q-var-mx6customboard.dts
+++ b/src/arm/nxp/imx/imx6q-var-mx6customboard.dts
@@ -16,7 +16,7 @@
 	compatible = "variscite,mx6customboard", "variscite,var-som-imx6q", "fsl,imx6q";
 
 	panel0: lvds-panel0 {
-		compatible =  "panel-lvds";
+		compatible = "panel-lvds";
 		backlight = <&backlight_lvds>;
 		width-mm = <152>;
 		height-mm = <91>;
@@ -43,7 +43,7 @@
 	};
 
 	panel1: lvds-panel1 {
-		compatible =  "panel-lvds";
+		compatible = "panel-lvds";
 		width-mm = <152>;
 		height-mm = <91>;
 		data-mapping = "jeida-18";
diff --git a/src/arm/nxp/imx/imx6qdl-apalis.dtsi b/src/arm/nxp/imx/imx6qdl-apalis.dtsi
index 4cc9652..ea40623 100644
--- a/src/arm/nxp/imx/imx6qdl-apalis.dtsi
+++ b/src/arm/nxp/imx/imx6qdl-apalis.dtsi
@@ -12,6 +12,13 @@
 	model = "Toradex Apalis iMX6Q/D Module";
 	compatible = "toradex,apalis_imx6q", "fsl,imx6q";
 
+	aliases {
+		mmc0 = &usdhc3; /* eMMC */
+		mmc1 = &usdhc1; /* MMC1 slot */
+		mmc2 = &usdhc2; /* SD1 slot */
+		/delete-property/ mmc3;
+	};
+
 	/* Will be filled by the bootloader */
 	memory@10000000 {
 		device_type = "memory";
@@ -166,7 +173,7 @@
 	reg_usb_host_vbus: regulator-usb-host-vbus {
 		compatible = "regulator-fixed";
 		enable-active-high;
-		gpio =  <&gpio1 0 GPIO_ACTIVE_HIGH>;
+		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_regulator_usbh_pwr>;
 		regulator-max-microvolt = <5000000>;
@@ -619,7 +626,6 @@
 		blocks = <0x5>;
 		id = <0>;
 		interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-controller;
 		interrupt-parent = <&gpio4>;
 		irq-trigger = <0x1>;
 		pinctrl-names = "default";
diff --git a/src/arm/nxp/imx/imx6qdl-colibri.dtsi b/src/arm/nxp/imx/imx6qdl-colibri.dtsi
index 11d9c7a..d3a7a6e 100644
--- a/src/arm/nxp/imx/imx6qdl-colibri.dtsi
+++ b/src/arm/nxp/imx/imx6qdl-colibri.dtsi
@@ -12,6 +12,13 @@
 	model = "Toradex Colibri iMX6DL/S Module";
 	compatible = "toradex,colibri_imx6dl", "fsl,imx6dl";
 
+	aliases {
+		mmc0 = &usdhc3; /* eMMC */
+		mmc1 = &usdhc1; /* MMC/SD Slot */
+		/delete-property/ mmc2;
+		/delete-property/ mmc3;
+	};
+
 	backlight: backlight {
 		compatible = "pwm-backlight";
 		brightness-levels = <0 45 63 88 119 158 203 255>;
@@ -543,7 +550,6 @@
 		blocks = <0x5>;
 		interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-parent = <&gpio6>;
-		interrupt-controller;
 		id = <0>;
 		irq-trigger = <0x1>;
 		pinctrl-names = "default";
diff --git a/src/arm/nxp/imx/imx6qdl-emcon-avari.dtsi b/src/arm/nxp/imx/imx6qdl-emcon-avari.dtsi
index f1a41c7..5587069 100644
--- a/src/arm/nxp/imx/imx6qdl-emcon-avari.dtsi
+++ b/src/arm/nxp/imx/imx6qdl-emcon-avari.dtsi
@@ -54,7 +54,7 @@
 	clk_codec: clock-codec {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-		clock-frequency  = <12000000>;
+		clock-frequency = <12000000>;
 	};
 
 	sound {
diff --git a/src/arm/nxp/imx/imx6qdl-emcon.dtsi b/src/arm/nxp/imx/imx6qdl-emcon.dtsi
index a63e73a..42b2ba2 100644
--- a/src/arm/nxp/imx/imx6qdl-emcon.dtsi
+++ b/src/arm/nxp/imx/imx6qdl-emcon.dtsi
@@ -225,7 +225,6 @@
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-controller;
 
 		onkey {
 			compatible = "dlg,da9063-onkey";
diff --git a/src/arm/nxp/imx/imx6qdl-mba6.dtsi b/src/arm/nxp/imx/imx6qdl-mba6.dtsi
index da0f8da..4d2abcd 100644
--- a/src/arm/nxp/imx/imx6qdl-mba6.dtsi
+++ b/src/arm/nxp/imx/imx6qdl-mba6.dtsi
@@ -500,21 +500,21 @@
 
 	pinctrl_pwm1: pwm1grp {
 		fsl,pins = <
-			/* 100 k PD, DSE 120 OHM, SPPEED LO */
+			/* 100 k PD, DSE 120 OHM, SPEED LO */
 			MX6QDL_PAD_GPIO_9__PWM1_OUT 0x00003050
 		>;
 	};
 
 	pinctrl_pwm3: pwm3grp {
 		fsl,pins = <
-			/* 100 k PD, DSE 120 OHM, SPPEED LO */
+			/* 100 k PD, DSE 120 OHM, SPEED LO */
 			MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x00003050
 		>;
 	};
 
 	pinctrl_pwm4: pwm4grp {
 		fsl,pins = <
-			/* 100 k PD, DSE 120 OHM, SPPEED LO */
+			/* 100 k PD, DSE 120 OHM, SPEED LO */
 			MX6QDL_PAD_SD4_DAT2__PWM4_OUT 0x00003050
 		>;
 	};
diff --git a/src/arm/nxp/imx/imx6qdl-phytec-pfla02.dtsi b/src/arm/nxp/imx/imx6qdl-phytec-pfla02.dtsi
index 1139745..c0c47ad 100644
--- a/src/arm/nxp/imx/imx6qdl-phytec-pfla02.dtsi
+++ b/src/arm/nxp/imx/imx6qdl-phytec-pfla02.dtsi
@@ -124,6 +124,7 @@
 		reg = <0x58>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <9 IRQ_TYPE_LEVEL_LOW>; /* active-low GPIO2_9 */
+		#interrupt-cells = <2>;
 		interrupt-controller;
 
 		regulators {
diff --git a/src/arm/nxp/imx/imx6qdl-phytec-phycore-som.dtsi b/src/arm/nxp/imx/imx6qdl-phytec-phycore-som.dtsi
index 86b4269..85e278e 100644
--- a/src/arm/nxp/imx/imx6qdl-phytec-phycore-som.dtsi
+++ b/src/arm/nxp/imx/imx6qdl-phytec-phycore-som.dtsi
@@ -100,6 +100,7 @@
 		interrupt-parent = <&gpio1>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
+		#interrupt-cells = <2>;
 		gpio-controller;
 		#gpio-cells = <2>;
 
diff --git a/src/arm/nxp/imx/imx6qdl-skov-cpu-revc.dtsi b/src/arm/nxp/imx/imx6qdl-skov-cpu-revc.dtsi
index b81799d..596b3bb 100644
--- a/src/arm/nxp/imx/imx6qdl-skov-cpu-revc.dtsi
+++ b/src/arm/nxp/imx/imx6qdl-skov-cpu-revc.dtsi
@@ -25,7 +25,7 @@
 		compatible = "ti,tsc2046e-adc";
 		reg = <0>;
 		pinctrl-0 = <&pinctrl_touch>;
-		pinctrl-names ="default";
+		pinctrl-names = "default";
 		spi-max-frequency = <1000000>;
 		interrupts-extended = <&gpio3 19 IRQ_TYPE_LEVEL_LOW>;
 		#io-channel-cells = <1>;
diff --git a/src/arm/nxp/imx/imx6qdl.dtsi b/src/arm/nxp/imx/imx6qdl.dtsi
index bda182e..81142c5 100644
--- a/src/arm/nxp/imx/imx6qdl.dtsi
+++ b/src/arm/nxp/imx/imx6qdl.dtsi
@@ -475,7 +475,7 @@
 						<&sdma 20 23 1>, <&sdma 21 23 1>, <&sdma 22 23 1>;
 					dma-names = "rxa", "rxb", "rxc",
 							"txa", "txb", "txc";
-					fsl,asrc-rate  = <48000>;
+					fsl,asrc-rate = <48000>;
 					fsl,asrc-width = <16>;
 					status = "okay";
 				};
diff --git a/src/arm/nxp/imx/imx6sx.dtsi b/src/arm/nxp/imx/imx6sx.dtsi
index f6b3592..df3a375 100644
--- a/src/arm/nxp/imx/imx6sx.dtsi
+++ b/src/arm/nxp/imx/imx6sx.dtsi
@@ -418,7 +418,7 @@
 					       <&sdma 21 23 1>, <&sdma 22 23 1>;
 					dma-names = "rxa", "rxb", "rxc",
 						    "txa", "txb", "txc";
-					fsl,asrc-rate  = <48000>;
+					fsl,asrc-rate = <48000>;
 					fsl,asrc-width = <16>;
 					status = "okay";
 				};
@@ -1010,7 +1010,7 @@
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
 				fsl,tuning-start-tap = <20>;
-				fsl,tuning-step= <2>;
+				fsl,tuning-step = <2>;
 				status = "disabled";
 			};
 
@@ -1024,7 +1024,7 @@
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
 				fsl,tuning-start-tap = <20>;
-				fsl,tuning-step= <2>;
+				fsl,tuning-step = <2>;
 				status = "disabled";
 			};
 
@@ -1038,7 +1038,7 @@
 				clock-names = "ipg", "ahb", "per";
 				bus-width = <4>;
 				fsl,tuning-start-tap = <20>;
-				fsl,tuning-step= <2>;
+				fsl,tuning-step = <2>;
 				status = "disabled";
 			};
 
diff --git a/src/arm/nxp/imx/imx6ul.dtsi b/src/arm/nxp/imx/imx6ul.dtsi
index 3b87d98..a27a755 100644
--- a/src/arm/nxp/imx/imx6ul.dtsi
+++ b/src/arm/nxp/imx/imx6ul.dtsi
@@ -364,7 +364,7 @@
 						<&sdma 20 23 1>, <&sdma 21 23 1>, <&sdma 22 23 1>;
 					dma-names = "rxa", "rxb", "rxc",
 						    "txa", "txb", "txc";
-					fsl,asrc-rate  = <48000>;
+					fsl,asrc-rate = <48000>;
 					fsl,asrc-width = <16>;
 					status = "okay";
 				};
diff --git a/src/arm/nxp/imx/imx6ull-phytec-tauri.dtsi b/src/arm/nxp/imx/imx6ull-phytec-tauri.dtsi
index 44cc4ff..d12fb44 100644
--- a/src/arm/nxp/imx/imx6ull-phytec-tauri.dtsi
+++ b/src/arm/nxp/imx/imx6ull-phytec-tauri.dtsi
@@ -116,7 +116,7 @@
 	tpm_tis: tpm@1 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_tpm>;
-		compatible = "tcg,tpm_tis-spi";
+		compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
 		reg = <1>;
 		spi-max-frequency = <20000000>;
 		interrupt-parent = <&gpio5>;
diff --git a/src/arm/nxp/imx/imx7-tqma7.dtsi b/src/arm/nxp/imx/imx7-tqma7.dtsi
index fe42b0a..3fc3130 100644
--- a/src/arm/nxp/imx/imx7-tqma7.dtsi
+++ b/src/arm/nxp/imx/imx7-tqma7.dtsi
@@ -128,11 +128,16 @@
 		};
 	};
 
-	/* NXP SE97BTP with temperature sensor + eeprom */
+	/* LM75A temperature sensor, TQMa7x 01xx */
+	lm75a: temperature-sensor@48 {
+		compatible = "national,lm75a";
+		reg = <0x48>;
+	};
+
+	/* NXP SE97BTP with temperature sensor + eeprom, TQMa7x 02xx */
 	se97b: temperature-sensor-eeprom@1e {
 		compatible = "nxp,se97b", "jedec,jc-42.4-temp";
 		reg = <0x1e>;
-		status = "okay";
 	};
 
 	/* ST M24C64 */
diff --git a/src/arm/nxp/imx/imx7d-colibri-emmc.dtsi b/src/arm/nxp/imx/imx7d-colibri-emmc.dtsi
index 3740e34..9670f45 100644
--- a/src/arm/nxp/imx/imx7d-colibri-emmc.dtsi
+++ b/src/arm/nxp/imx/imx7d-colibri-emmc.dtsi
@@ -11,6 +11,10 @@
 		/* Required to properly pass MAC addresses from bootloader. */
 		ethernet0 = &fec1;
 		ethernet1 = &fec2;
+		mmc0 = &usdhc3; /* eMMC */
+		mmc1 = &usdhc1; /* MMC/SD slot */
+		/delete-property/ mmc2;
+		/delete-property/ mmc3;
 	};
 
 	memory@80000000 {
diff --git a/src/arm/nxp/imx/imx7d-flex-concentrator.dts b/src/arm/nxp/imx/imx7d-flex-concentrator.dts
index 3a72384..9984b34 100644
--- a/src/arm/nxp/imx/imx7d-flex-concentrator.dts
+++ b/src/arm/nxp/imx/imx7d-flex-concentrator.dts
@@ -130,7 +130,7 @@
 	 * TCG specification - Section 6.4.1 Clocking:
 	 * TPM shall support a SPI clock frequency range of 10-24 MHz.
 	 */
-	st33htph: tpm-tis@0 {
+	st33htph: tpm@0 {
 		compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi";
 		reg = <0>;
 		spi-max-frequency = <24000000>;
diff --git a/src/arm/nxp/imx/imx7d-meerkat96.dts b/src/arm/nxp/imx/imx7d-meerkat96.dts
index dd8003b..f0fda15 100644
--- a/src/arm/nxp/imx/imx7d-meerkat96.dts
+++ b/src/arm/nxp/imx/imx7d-meerkat96.dts
@@ -212,7 +212,7 @@
 	keep-power-in-suspend;
 	wakeup-source;
 	vmmc-supply = <&reg_wlreg_on>;
-	vqmmc-supply =<&reg_3p3v>;
+	vqmmc-supply = <&reg_3p3v>;
 	status = "okay";
 
 	brcmf: wifi@1 {
diff --git a/src/arm/nxp/imx/imx7d-pico-dwarf.dts b/src/arm/nxp/imx/imx7d-pico-dwarf.dts
index 12361fc..1b96565 100644
--- a/src/arm/nxp/imx/imx7d-pico-dwarf.dts
+++ b/src/arm/nxp/imx/imx7d-pico-dwarf.dts
@@ -63,6 +63,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;
 		#interrupt-cells = <2>;
+		interrupt-controller;
 		reg = <0x25>;
 	};
 
diff --git a/src/arm/nxp/imx/imx7d-pico.dtsi b/src/arm/nxp/imx/imx7d-pico.dtsi
index c5eefe8..8d5037a 100644
--- a/src/arm/nxp/imx/imx7d-pico.dtsi
+++ b/src/arm/nxp/imx/imx7d-pico.dtsi
@@ -108,6 +108,14 @@
 	assigned-clock-rates = <0>, <32768>;
 };
 
+&cpu0 {
+	cpu-supply = <&sw1a_reg>;
+};
+
+&cpu1 {
+	cpu-supply = <&sw1a_reg>;
+};
+
 &ecspi3 {
 	cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
diff --git a/src/arm/nxp/imx/imx7d-smegw01.dts b/src/arm/nxp/imx/imx7d-smegw01.dts
index 85b97b5..7ed27c7 100644
--- a/src/arm/nxp/imx/imx7d-smegw01.dts
+++ b/src/arm/nxp/imx/imx7d-smegw01.dts
@@ -149,7 +149,7 @@
 
 &i2c2 {
 	pinctrl-names = "default";
-	pinctrl-0 =<&pinctrl_i2c2>;
+	pinctrl-0 = <&pinctrl_i2c2>;
 	clock-frequency = <100000>;
 	status = "okay";
 
diff --git a/src/arm/nxp/imx/imx7d.dtsi b/src/arm/nxp/imx/imx7d.dtsi
index 4b94b8a..0484e34 100644
--- a/src/arm/nxp/imx/imx7d.dtsi
+++ b/src/arm/nxp/imx/imx7d.dtsi
@@ -217,9 +217,6 @@
 };
 
 &ca_funnel_in_ports {
-	#address-cells = <1>;
-	#size-cells = <0>;
-
 	port@1 {
 		reg = <1>;
 		ca_funnel_in_port1: endpoint {
diff --git a/src/arm/nxp/imx/imx7s.dtsi b/src/arm/nxp/imx/imx7s.dtsi
index 5387da8..9c81c6b 100644
--- a/src/arm/nxp/imx/imx7s.dtsi
+++ b/src/arm/nxp/imx/imx7s.dtsi
@@ -183,6 +183,15 @@
 		interrupt-parent = <&gpc>;
 		ranges;
 
+		ocram: sram@900000 {
+			compatible = "mmio-sram";
+			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&clks IMX7D_OCRAM_CLK>;
+		};
+
 		funnel@30041000 {
 			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
 			reg = <0x30041000 0x1000>;
@@ -190,7 +199,11 @@
 			clock-names = "apb_pclk";
 
 			ca_funnel_in_ports: in-ports {
-				port {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
 					ca_funnel_in_port0: endpoint {
 						remote-endpoint = <&etm0_out_port>;
 					};
@@ -605,6 +618,7 @@
 					nvmem-cells = <&tempmon_calib>,	<&fuse_grade>;
 					nvmem-cell-names = "calib", "temp_grade";
 					clocks = <&clks IMX7D_PLL_SYS_MAIN_CLK>;
+					#thermal-sensor-cells = <0>;
 				};
 			};
 
@@ -720,6 +734,8 @@
 				clocks = <&clks IMX7D_ECSPI4_ROOT_CLK>,
 					<&clks IMX7D_ECSPI4_ROOT_CLK>;
 				clock-names = "ipg", "per";
+				dma-names = "rx", "tx";
+				dmas = <&sdma 6 7 1>, <&sdma 7 7 2>;
 				status = "disabled";
 			};
 
@@ -811,7 +827,7 @@
 			};
 
 			lcdif: lcdif@30730000 {
-				compatible = "fsl,imx7d-lcdif", "fsl,imx28-lcdif";
+				compatible = "fsl,imx7d-lcdif", "fsl,imx6sx-lcdif";
 				reg = <0x30730000 0x10000>;
 				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_LCDIF_PIXEL_ROOT_CLK>,
@@ -850,6 +866,26 @@
 					};
 				};
 			};
+
+			mipi_dsi: dsi@30760000 {
+				compatible = "fsl,imx7d-mipi-dsim", "fsl,imx8mm-mipi-dsim";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x30760000 0x400>;
+				clocks = <&clks IMX7D_MIPI_DSI_ROOT_CLK>,
+					 <&clks IMX7D_MIPI_DPHY_ROOT_CLK>;
+				clock-names = "bus_clk", "sclk_mipi";
+				assigned-clocks = <&clks IMX7D_MIPI_DSI_ROOT_SRC>,
+						  <&clks IMX7D_PLL_SYS_PFD5_CLK>;
+				assigned-clock-parents = <&clks IMX7D_PLL_SYS_PFD5_CLK>;
+				assigned-clock-rates = <0>, <333000000>;
+				power-domains = <&pgc_mipi_phy>;
+				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+				samsung,burst-clock-frequency = <891000000>;
+				samsung,esc-clock-frequency = <20000000>;
+				samsung,pll-clock-frequency = <24000000>;
+				status = "disabled";
+			};
 		};
 
 		aips3: bus@30800000 {
@@ -875,6 +911,8 @@
 					clocks = <&clks IMX7D_ECSPI1_ROOT_CLK>,
 						<&clks IMX7D_ECSPI1_ROOT_CLK>;
 					clock-names = "ipg", "per";
+					dma-names = "rx", "tx";
+					dmas = <&sdma 0 7 1>, <&sdma 1 7 2>;
 					status = "disabled";
 				};
 
@@ -887,6 +925,8 @@
 					clocks = <&clks IMX7D_ECSPI2_ROOT_CLK>,
 						<&clks IMX7D_ECSPI2_ROOT_CLK>;
 					clock-names = "ipg", "per";
+					dma-names = "rx", "tx";
+					dmas = <&sdma 2 7 1>, <&sdma 3 7 2>;
 					status = "disabled";
 				};
 
@@ -899,6 +939,8 @@
 					clocks = <&clks IMX7D_ECSPI3_ROOT_CLK>,
 						<&clks IMX7D_ECSPI3_ROOT_CLK>;
 					clock-names = "ipg", "per";
+					dma-names = "rx", "tx";
+					dmas = <&sdma 4 7 1>, <&sdma 5 7 2>;
 					status = "disabled";
 				};
 
@@ -1275,7 +1317,7 @@
 		gpmi: nand-controller@33002000 {
 			compatible = "fsl,imx7d-gpmi-nand";
 			#address-cells = <1>;
-			#size-cells = <1>;
+			#size-cells = <0>;
 			reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
 			reg-names = "gpmi-nand", "bch";
 			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/src/arm/nxp/imx/mba6ulx.dtsi b/src/arm/nxp/imx/mba6ulx.dtsi
index 5a8b867..e78d0a7 100644
--- a/src/arm/nxp/imx/mba6ulx.dtsi
+++ b/src/arm/nxp/imx/mba6ulx.dtsi
@@ -467,7 +467,7 @@
 
 	pinctrl_pwm2: pwm2grp {
 		fsl,pins = <
-			/* 100 k PD, DSE 120 OHM, SPPEED LO */
+			/* 100 k PD, DSE 120 OHM, SPEED LO */
 			MX6UL_PAD_GPIO1_IO09__PWM2_OUT		0x00003050
 		>;
 	};
diff --git a/src/arm/nxp/lpc/lpc18xx.dtsi b/src/arm/nxp/lpc/lpc18xx.dtsi
index 9cf09c1..6dd7329 100644
--- a/src/arm/nxp/lpc/lpc18xx.dtsi
+++ b/src/arm/nxp/lpc/lpc18xx.dtsi
@@ -74,7 +74,7 @@
 		sct_pwm: pwm@40000000 {
 			compatible = "nxp,lpc1850-sct-pwm";
 			reg = <0x40000000 0x1000>;
-			clocks =<&ccu1 CLK_CPU_SCT>;
+			clocks = <&ccu1 CLK_CPU_SCT>;
 			clock-names = "pwm";
 			resets = <&rgu 37>;
 			#pwm-cells = <3>;
diff --git a/src/arm/nxp/ls/ls1021a.dtsi b/src/arm/nxp/ls/ls1021a.dtsi
index 49c78c8..d471cc5 100644
--- a/src/arm/nxp/ls/ls1021a.dtsi
+++ b/src/arm/nxp/ls/ls1021a.dtsi
@@ -112,7 +112,7 @@
 			compatible = "fsl,ls1021a-msi";
 			reg = <0x0 0x1570e00 0x0 0x8>;
 			msi-controller;
-			interrupts =  <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		msi2: msi-controller@1570e08 {
diff --git a/src/arm/nxp/mxs/imx23-sansa.dts b/src/arm/nxp/mxs/imx23-sansa.dts
index 636cf09..b23e7ad 100644
--- a/src/arm/nxp/mxs/imx23-sansa.dts
+++ b/src/arm/nxp/mxs/imx23-sansa.dts
@@ -175,10 +175,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "i2c-gpio";
-		gpios = <
-			&gpio1 24 0		/* SDA */
-			&gpio1 22 0		/* SCL */
-		>;
+		sda-gpios = <&gpio1 24 0>;
+		scl-gpios = <&gpio1 22 0>;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
 	};
 
@@ -186,10 +184,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "i2c-gpio";
-		gpios = <
-			&gpio0 31 0		/* SDA */
-			&gpio0 30 0		/* SCL */
-		>;
+		sda-gpios = <&gpio0 31 0>;
+		scl-gpios = <&gpio0 30 0>;
 		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
 
 		touch: touch@20 {
diff --git a/src/arm/nxp/mxs/imx23.dtsi b/src/arm/nxp/mxs/imx23.dtsi
index fdf18b7..0309592 100644
--- a/src/arm/nxp/mxs/imx23.dtsi
+++ b/src/arm/nxp/mxs/imx23.dtsi
@@ -110,7 +110,7 @@
 				reg = <0x80018000 0x2000>;
 
 				gpio0: gpio@0 {
-					compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx23-gpio";
 					reg = <0>;
 					interrupts = <16>;
 					gpio-controller;
@@ -120,7 +120,7 @@
 				};
 
 				gpio1: gpio@1 {
-					compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx23-gpio";
 					reg = <1>;
 					interrupts = <17>;
 					gpio-controller;
@@ -130,7 +130,7 @@
 				};
 
 				gpio2: gpio@2 {
-					compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx23-gpio";
 					reg = <2>;
 					interrupts = <18>;
 					gpio-controller;
@@ -412,7 +412,7 @@
 				status = "disabled";
 			};
 
-			dma_apbx: dma-apbx@80024000 {
+			dma_apbx: dma-controller@80024000 {
 				compatible = "fsl,imx23-dma-apbx";
 				reg = <0x80024000 0x2000>;
 				interrupts = <7>, <5>, <9>, <26>,
@@ -484,7 +484,7 @@
 			ranges;
 
 			clks: clkctrl@80040000 {
-				compatible = "fsl,imx23-clkctrl", "fsl,clkctrl";
+				compatible = "fsl,imx23-clkctrl";
 				reg = <0x80040000 0x2000>;
 				#clock-cells = <1>;
 			};
diff --git a/src/arm/nxp/mxs/imx28-lwe.dtsi b/src/arm/nxp/mxs/imx28-lwe.dtsi
index bb971e6..69fcb0d 100644
--- a/src/arm/nxp/mxs/imx28-lwe.dtsi
+++ b/src/arm/nxp/mxs/imx28-lwe.dtsi
@@ -18,6 +18,7 @@
 
 	memory@40000000 {
 		reg = <0x40000000 0x08000000>;
+		device_type = "memory";
 	};
 
 	reg_3v3: regulator-reg-3v3 {
diff --git a/src/arm/nxp/mxs/imx28-tx28.dts b/src/arm/nxp/mxs/imx28-tx28.dts
index 153e401..5485fe11 100644
--- a/src/arm/nxp/mxs/imx28-tx28.dts
+++ b/src/arm/nxp/mxs/imx28-tx28.dts
@@ -260,6 +260,7 @@
 	sgtl5000: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_3p3v>;
 		clocks = <&mclk>;
diff --git a/src/arm/nxp/mxs/imx28.dtsi b/src/arm/nxp/mxs/imx28.dtsi
index 6932d23..4817fba 100644
--- a/src/arm/nxp/mxs/imx28.dtsi
+++ b/src/arm/nxp/mxs/imx28.dtsi
@@ -164,7 +164,7 @@
 				reg = <0x80018000 0x2000>;
 
 				gpio0: gpio@0 {
-					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx28-gpio";
 					reg = <0>;
 					interrupts = <127>;
 					gpio-controller;
@@ -174,7 +174,7 @@
 				};
 
 				gpio1: gpio@1 {
-					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx28-gpio";
 					reg = <1>;
 					interrupts = <126>;
 					gpio-controller;
@@ -184,7 +184,7 @@
 				};
 
 				gpio2: gpio@2 {
-					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx28-gpio";
 					reg = <2>;
 					interrupts = <125>;
 					gpio-controller;
@@ -194,7 +194,7 @@
 				};
 
 				gpio3: gpio@3 {
-					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx28-gpio";
 					reg = <3>;
 					interrupts = <124>;
 					gpio-controller;
@@ -204,7 +204,7 @@
 				};
 
 				gpio4: gpio@4 {
-					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					compatible = "fsl,imx28-gpio";
 					reg = <4>;
 					interrupts = <123>;
 					gpio-controller;
@@ -990,7 +990,7 @@
 				status = "disabled";
 			};
 
-			dma_apbx: dma-apbx@80024000 {
+			dma_apbx: dma-controller@80024000 {
 				compatible = "fsl,imx28-dma-apbx";
 				reg = <0x80024000 0x2000>;
 				interrupts = <78>, <79>, <66>, <0>,
@@ -1100,7 +1100,7 @@
 			ranges;
 
 			clks: clkctrl@80040000 {
-				compatible = "fsl,imx28-clkctrl", "fsl,clkctrl";
+				compatible = "fsl,imx28-clkctrl";
 				reg = <0x80040000 0x2000>;
 				#clock-cells = <1>;
 			};
diff --git a/src/arm/nxp/vf/vf-colibri-eval-v3.dtsi b/src/arm/nxp/vf/vf-colibri-eval-v3.dtsi
index 14c411f..5a19da9 100644
--- a/src/arm/nxp/vf/vf-colibri-eval-v3.dtsi
+++ b/src/arm/nxp/vf/vf-colibri-eval-v3.dtsi
@@ -55,7 +55,7 @@
 	brightness-levels = <0 4 8 16 32 64 128 255>;
 	default-brightness-level = <6>;
 	power-supply = <&reg_3v3>;
-	status  = "okay";
+	status = "okay";
 };
 
 &dcu0 {
diff --git a/src/arm/nxp/vf/vf610-bk4.dts b/src/arm/nxp/vf/vf610-bk4.dts
index e4f691d..722182f 100644
--- a/src/arm/nxp/vf/vf610-bk4.dts
+++ b/src/arm/nxp/vf/vf610-bk4.dts
@@ -68,7 +68,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		/* PTD12 ->RPIO[91] */
-		sck-gpios  = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		sck-gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
 		/* PTD10 ->RPIO[89] */
 		miso-gpios = <&gpio2 25 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <0>;
@@ -79,7 +79,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			/* PTB18 -> RGPIO[40] */
-			load-gpios  = <&gpio1 8 GPIO_ACTIVE_LOW>;
+			load-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
 			spi-max-frequency = <100000>;
 		};
 	};
diff --git a/src/arm/nxp/vf/vf610-zii-cfu1.dts b/src/arm/nxp/vf/vf610-zii-cfu1.dts
index 1a19aec..7e72f86 100644
--- a/src/arm/nxp/vf/vf610-zii-cfu1.dts
+++ b/src/arm/nxp/vf/vf610-zii-cfu1.dts
@@ -162,7 +162,7 @@
 		suppress-preamble;
 		status = "okay";
 
-		switch0: switch0@0 {
+		switch0: ethernet-switch@0 {
 			compatible = "marvell,mv88e6085";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_switch>;
@@ -173,26 +173,26 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			ports {
+			ethernet-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				ethernet-port@0 {
 					reg = <0>;
 					label = "eth_cu_1000_1";
 				};
 
-				port@1 {
+				ethernet-port@1 {
 					reg = <1>;
 					label = "eth_cu_1000_2";
 				};
 
-				port@2 {
+				ethernet-port@2 {
 					reg = <2>;
 					label = "eth_cu_1000_3";
 				};
 
-				port@5 {
+				ethernet-port@5 {
 					reg = <5>;
 					label = "eth_fc_1000_1";
 					phy-mode = "1000base-x";
@@ -200,7 +200,7 @@
 					sfp = <&sff>;
 				};
 
-				port@6 {
+				ethernet-port@6 {
 					reg = <6>;
 					phy-mode = "rmii";
 					ethernet = <&fec1>;
diff --git a/src/arm/nxp/vf/vf610-zii-dev-rev-b.dts b/src/arm/nxp/vf/vf610-zii-dev-rev-b.dts
index 16b4e06..029f49b 100644
--- a/src/arm/nxp/vf/vf610-zii-dev-rev-b.dts
+++ b/src/arm/nxp/vf/vf610-zii-dev-rev-b.dts
@@ -294,11 +294,11 @@
 		pinctrl-names = "default";
 		#address-cells = <1>;
 		#size-cells = <0>;
-		sck-gpios  = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		sck-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
 		mosi-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
 		miso-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-		cs-gpios  = <&gpio1  9 GPIO_ACTIVE_LOW
-			     &gpio1  8 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio1 9 GPIO_ACTIVE_LOW
+			    &gpio1 8 GPIO_ACTIVE_HIGH>;
 		num-chipselects = <2>;
 
 		flash@0 {
@@ -338,6 +338,7 @@
 		reg = <0x22>;
 		gpio-controller;
 		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
 		interrupt-controller;
 		interrupt-parent = <&gpio3>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
diff --git a/src/arm/nxp/vf/vf610-zii-scu4-aib.dts b/src/arm/nxp/vf/vf610-zii-scu4-aib.dts
index df13354..77492ee 100644
--- a/src/arm/nxp/vf/vf610-zii-scu4-aib.dts
+++ b/src/arm/nxp/vf/vf610-zii-scu4-aib.dts
@@ -47,17 +47,17 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch0: switch0@0 {
+			switch0: ethernet-switch@0 {
 				compatible = "marvell,mv88e6190";
 				reg = <0>;
 				dsa,member = <0 0>;
 				eeprom-length = <65536>;
 
-				ports {
+				ethernet-ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@0 {
+					ethernet-port@0 {
 						reg = <0>;
 						phy-mode = "rmii";
 						ethernet = <&fec1>;
@@ -68,37 +68,37 @@
 						};
 					};
 
-					port@1 {
+					ethernet-port@1 {
 						reg = <1>;
 						label = "aib2main_1";
 					};
 
-					port@2 {
+					ethernet-port@2 {
 						reg = <2>;
 						label = "aib2main_2";
 					};
 
-					port@3 {
+					ethernet-port@3 {
 						reg = <3>;
 						label = "eth_cu_1000_5";
 					};
 
-					port@4 {
+					ethernet-port@4 {
 						reg = <4>;
 						label = "eth_cu_1000_6";
 					};
 
-					port@5 {
+					ethernet-port@5 {
 						reg = <5>;
 						label = "eth_cu_1000_4";
 					};
 
-					port@6 {
+					ethernet-port@6 {
 						reg = <6>;
 						label = "eth_cu_1000_7";
 					};
 
-					port@7 {
+					ethernet-port@7 {
 						reg = <7>;
 						label = "modem_pic";
 
@@ -108,7 +108,7 @@
 						};
 					};
 
-					switch0port10: port@10 {
+					switch0port10: ethernet-port@10 {
 						reg = <10>;
 						label = "dsa";
 						phy-mode = "xgmii";
@@ -130,32 +130,32 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch1: switch1@0 {
+			switch1: ethernet-switch@0 {
 				compatible = "marvell,mv88e6190";
 				reg = <0>;
 				dsa,member = <0 1>;
 				eeprom-length = <65536>;
 
-				ports {
+				ethernet-ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@1 {
+					ethernet-port@1 {
 						reg = <1>;
 						label = "eth_cu_1000_3";
 					};
 
-					port@2 {
+					ethernet-port@2 {
 						reg = <2>;
 						label = "eth_cu_100_2";
 					};
 
-					port@3 {
+					ethernet-port@3 {
 						reg = <3>;
 						label = "eth_cu_100_3";
 					};
 
-					switch1port9: port@9 {
+					switch1port9: ethernet-port@9 {
 						reg = <9>;
 						label = "dsa";
 						phy-mode = "xgmii";
@@ -168,7 +168,7 @@
 						};
 					};
 
-					switch1port10: port@10 {
+					switch1port10: ethernet-port@10 {
 						reg = <10>;
 						label = "dsa";
 						phy-mode = "xgmii";
@@ -188,17 +188,17 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch2: switch2@0 {
+			switch2: ethernet-switch@0 {
 				compatible = "marvell,mv88e6190";
 				reg = <0>;
 				dsa,member = <0 2>;
 				eeprom-length = <65536>;
 
-				ports {
+				ethernet-ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@2 {
+					ethernet-port@2 {
 						reg = <2>;
 						label = "eth_fc_1000_2";
 						phy-mode = "1000base-x";
@@ -206,7 +206,7 @@
 						sfp = <&sff1>;
 					};
 
-					port@3 {
+					ethernet-port@3 {
 						reg = <3>;
 						label = "eth_fc_1000_3";
 						phy-mode = "1000base-x";
@@ -214,7 +214,7 @@
 						sfp = <&sff2>;
 					};
 
-					port@4 {
+					ethernet-port@4 {
 						reg = <4>;
 						label = "eth_fc_1000_4";
 						phy-mode = "1000base-x";
@@ -222,7 +222,7 @@
 						sfp = <&sff3>;
 					};
 
-					port@5 {
+					ethernet-port@5 {
 						reg = <5>;
 						label = "eth_fc_1000_5";
 						phy-mode = "1000base-x";
@@ -230,7 +230,7 @@
 						sfp = <&sff4>;
 					};
 
-					port@6 {
+					ethernet-port@6 {
 						reg = <6>;
 						label = "eth_fc_1000_6";
 						phy-mode = "1000base-x";
@@ -238,7 +238,7 @@
 						sfp = <&sff5>;
 					};
 
-					port@7 {
+					ethernet-port@7 {
 						reg = <7>;
 						label = "eth_fc_1000_7";
 						phy-mode = "1000base-x";
@@ -246,7 +246,7 @@
 						sfp = <&sff6>;
 					};
 
-					port@9 {
+					ethernet-port@9 {
 						reg = <9>;
 						label = "eth_fc_1000_1";
 						phy-mode = "1000base-x";
@@ -254,7 +254,7 @@
 						sfp = <&sff0>;
 					};
 
-					switch2port10: port@10 {
+					switch2port10: ethernet-port@10 {
 						reg = <10>;
 						label = "dsa";
 						phy-mode = "2500base-x";
@@ -276,17 +276,17 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			switch3: switch3@0 {
+			switch3: ethernet-switch@0 {
 				compatible = "marvell,mv88e6190";
 				reg = <0>;
 				dsa,member = <0 3>;
 				eeprom-length = <65536>;
 
-				ports {
+				ethernet-ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@2 {
+					ethernet-port@2 {
 						reg = <2>;
 						label = "eth_fc_1000_8";
 						phy-mode = "1000base-x";
@@ -294,7 +294,7 @@
 						sfp = <&sff7>;
 					};
 
-					port@3 {
+					ethernet-port@3 {
 						reg = <3>;
 						label = "eth_fc_1000_9";
 						phy-mode = "1000base-x";
@@ -302,7 +302,7 @@
 						sfp = <&sff8>;
 					};
 
-					port@4 {
+					ethernet-port@4 {
 						reg = <4>;
 						label = "eth_fc_1000_10";
 						phy-mode = "1000base-x";
@@ -310,7 +310,7 @@
 						sfp = <&sff9>;
 					};
 
-					switch3port9: port@9 {
+					switch3port9: ethernet-port@9 {
 						reg = <9>;
 						label = "dsa";
 						phy-mode = "2500base-x";
@@ -322,7 +322,7 @@
 						};
 					};
 
-					switch3port10: port@10 {
+					switch3port10: ethernet-port@10 {
 						reg = <10>;
 						label = "dsa";
 						phy-mode = "xgmii";
diff --git a/src/arm/nxp/vf/vf610-zii-spb4.dts b/src/arm/nxp/vf/vf610-zii-spb4.dts
index 1461804..2a49046 100644
--- a/src/arm/nxp/vf/vf610-zii-spb4.dts
+++ b/src/arm/nxp/vf/vf610-zii-spb4.dts
@@ -123,7 +123,7 @@
 		suppress-preamble;
 		status = "okay";
 
-		switch0: switch0@0 {
+		switch0: ethernet-switch@0 {
 			compatible = "marvell,mv88e6190";
 			pinctrl-0 = <&pinctrl_gpio_switch0>;
 			pinctrl-names = "default";
@@ -134,11 +134,11 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			ports {
+			ethernet-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				ethernet-port@0 {
 					reg = <0>;
 					phy-mode = "rmii";
 					ethernet = <&fec1>;
@@ -149,32 +149,32 @@
 					};
 				};
 
-				port@1 {
+				ethernet-port@1 {
 					reg = <1>;
 					label = "eth_cu_1000_1";
 				};
 
-				port@2 {
+				ethernet-port@2 {
 					reg = <2>;
 					label = "eth_cu_1000_2";
 				};
 
-				port@3 {
+				ethernet-port@3 {
 					reg = <3>;
 					label = "eth_cu_1000_3";
 				};
 
-				port@4 {
+				ethernet-port@4 {
 					reg = <4>;
 					label = "eth_cu_1000_4";
 				};
 
-				port@5 {
+				ethernet-port@5 {
 					reg = <5>;
 					label = "eth_cu_1000_5";
 				};
 
-				port@6 {
+				ethernet-port@6 {
 					reg = <6>;
 					label = "eth_cu_1000_6";
 				};
diff --git a/src/arm/nxp/vf/vf610-zii-ssmb-dtu.dts b/src/arm/nxp/vf/vf610-zii-ssmb-dtu.dts
index 463c245..078d869 100644
--- a/src/arm/nxp/vf/vf610-zii-ssmb-dtu.dts
+++ b/src/arm/nxp/vf/vf610-zii-ssmb-dtu.dts
@@ -112,7 +112,7 @@
 		suppress-preamble;
 		status = "okay";
 
-		switch0: switch0@0 {
+		switch0: ethernet-switch@0 {
 			compatible = "marvell,mv88e6190";
 			pinctrl-0 = <&pinctrl_gpio_switch0>;
 			pinctrl-names = "default";
@@ -123,11 +123,11 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			ports {
+			ethernet-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				ethernet-port@0 {
 					reg = <0>;
 					phy-mode = "rmii";
 					ethernet = <&fec1>;
@@ -138,27 +138,27 @@
 					};
 				};
 
-				port@1 {
+				ethernet-port@1 {
 					reg = <1>;
 					label = "eth_cu_100_3";
 				};
 
-				port@5 {
+				ethernet-port@5 {
 					reg = <5>;
 					label = "eth_cu_1000_4";
 				};
 
-				port@6 {
+				ethernet-port@6 {
 					reg = <6>;
 					label = "eth_cu_1000_5";
 				};
 
-				port@8 {
+				ethernet-port@8 {
 					reg = <8>;
 					label = "eth_cu_1000_1";
 				};
 
-				port@9 {
+				ethernet-port@9 {
 					reg = <9>;
 					label = "eth_cu_1000_2";
 					phy-handle = <&phy9>;
@@ -167,12 +167,12 @@
 				};
 			};
 
-			mdio1 {
+			mdio-external {
 				compatible = "marvell,mv88e6xxx-mdio-external";
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				phy9: phy9@0 {
+				phy9: ethernet-phy@0 {
 					compatible = "ethernet-phy-ieee802.3-c45";
 					pinctrl-0 = <&pinctrl_gpio_phy9>;
 					pinctrl-names = "default";
diff --git a/src/arm/nxp/vf/vf610-zii-ssmb-spu3.dts b/src/arm/nxp/vf/vf610-zii-ssmb-spu3.dts
index f5ae0d5..22c8f44 100644
--- a/src/arm/nxp/vf/vf610-zii-ssmb-spu3.dts
+++ b/src/arm/nxp/vf/vf610-zii-ssmb-spu3.dts
@@ -137,7 +137,7 @@
 		suppress-preamble;
 		status = "okay";
 
-		switch0: switch0@0 {
+		switch0: ethernet-switch@0 {
 			compatible = "marvell,mv88e6190";
 			pinctrl-0 = <&pinctrl_gpio_switch0>;
 			pinctrl-names = "default";
@@ -148,11 +148,11 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			ports {
+			ethernet-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
+				ethernet-port@0 {
 					reg = <0>;
 					phy-mode = "rmii";
 					ethernet = <&fec1>;
@@ -163,32 +163,32 @@
 					};
 				};
 
-				port@1 {
+				ethernet-port@1 {
 					reg = <1>;
 					label = "eth_cu_1000_1";
 				};
 
-				port@2 {
+				ethernet-port@2 {
 					reg = <2>;
 					label = "eth_cu_1000_2";
 				};
 
-				port@3 {
+				ethernet-port@3 {
 					reg = <3>;
 					label = "eth_cu_1000_3";
 				};
 
-				port@4 {
+				ethernet-port@4 {
 					reg = <4>;
 					label = "eth_cu_1000_4";
 				};
 
-				port@5 {
+				ethernet-port@5 {
 					reg = <5>;
 					label = "eth_cu_1000_5";
 				};
 
-				port@6 {
+				ethernet-port@6 {
 					reg = <6>;
 					label = "eth_cu_1000_6";
 				};