diff --git a/Bindings/net/dsa/dsa.yaml b/Bindings/net/dsa/dsa.yaml
index 6107189..2abd036 100644
--- a/Bindings/net/dsa/dsa.yaml
+++ b/Bindings/net/dsa/dsa.yaml
@@ -46,4 +46,10 @@
             $ref: dsa-port.yaml#
             unevaluatedProperties: false
 
+oneOf:
+  - required:
+      - ports
+  - required:
+      - ethernet-ports
+
 ...
diff --git a/Bindings/net/dsa/marvell,mv88e6060.yaml b/Bindings/net/dsa/marvell,mv88e6060.yaml
new file mode 100644
index 0000000..4f1adf0
--- /dev/null
+++ b/Bindings/net/dsa/marvell,mv88e6060.yaml
@@ -0,0 +1,88 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6060.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell MV88E6060 DSA switch
+
+maintainers:
+  - Andrew Lunn <andrew@lunn.ch>
+
+description:
+  The Marvell MV88E6060 switch has been produced and sold by Marvell
+  since at least 2008. The switch has one pin ADDR4 that controls the
+  MDIO address of the switch to be 0x10 or 0x00, and on the MDIO bus
+  connected to the switch, the PHYs inside the switch appear as
+  independent devices on address 0x00-0x04 or 0x10-0x14, so in difference
+  from many other DSA switches this switch does not have an internal
+  MDIO bus for the PHY devices.
+
+properties:
+  compatible:
+    const: marvell,mv88e6060
+    description:
+      The MV88E6060 is the oldest Marvell DSA switch product, and
+      as such a bit limited in features compared to later hardware.
+
+  reg:
+    maxItems: 1
+
+  reset-gpios:
+    description:
+      GPIO to be used to reset the whole device
+    maxItems: 1
+
+allOf:
+  - $ref: dsa.yaml#/$defs/ethernet-ports
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ethernet-switch@16 {
+            compatible = "marvell,mv88e6060";
+            reg = <16>;
+
+            ethernet-ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                ethernet-port@0 {
+                    reg = <0>;
+                    label = "lan1";
+                };
+                ethernet-port@1 {
+                    reg = <1>;
+                    label = "lan2";
+                };
+                ethernet-port@2 {
+                    reg = <2>;
+                    label = "lan3";
+                };
+                ethernet-port@3 {
+                    reg = <3>;
+                    label = "lan4";
+                };
+                ethernet-port@5 {
+                    reg = <5>;
+                    phy-mode = "rev-mii";
+                    ethernet = <&ethc>;
+                    fixed-link {
+                        speed = <100>;
+                        full-duplex;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Bindings/net/dsa/marvell,mv88e6xxx.yaml b/Bindings/net/dsa/marvell,mv88e6xxx.yaml
new file mode 100644
index 0000000..19f15bd
--- /dev/null
+++ b/Bindings/net/dsa/marvell,mv88e6xxx.yaml
@@ -0,0 +1,337 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6xxx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell MV88E6xxx DSA switch family
+
+maintainers:
+  - Andrew Lunn <andrew@lunn.ch>
+
+description:
+  The Marvell MV88E6xxx switch series has been produced and sold
+  by Marvell since at least 2008. The switch has a few compatibles which
+  just indicate the base address of the switch, then operating systems
+  can investigate switch ID registers to find out which actual version
+  of the switch it is dealing with.
+
+properties:
+  compatible:
+    oneOf:
+      - enum:
+          - marvell,mv88e6085
+          - marvell,mv88e6190
+          - marvell,mv88e6250
+        description: |
+          marvell,mv88e6085: This switch uses base address 0x10.
+            This switch and its siblings will be autodetected from
+            ID registers found in the switch, so only "marvell,mv88e6085" should be
+            specified. This includes the following list of MV88Exxxx switches:
+            6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, 6171, 6172, 6175, 6176,
+            6185, 6240, 6320, 6321, 6341, 6350, 6351, 6352
+          marvell,mv88e6190: This switch uses base address 0x00.
+            This switch and its siblings will be autodetected from
+            ID registers found in the switch, so only "marvell,mv88e6190" should be
+            specified. This includes the following list of MV88Exxxx switches:
+            6190, 6190X, 6191, 6290, 6361, 6390, 6390X
+          marvell,mv88e6250: This switch uses base address 0x08 or 0x18.
+            This switch and its siblings will be autodetected from
+            ID registers found in the switch, so only "marvell,mv88e6250" should be
+            specified. This includes the following list of MV88Exxxx switches:
+            6220, 6250
+      - items:
+          - const: marvell,turris-mox-mv88e6085
+          - const: marvell,mv88e6085
+      - items:
+          - const: marvell,turris-mox-mv88e6190
+          - const: marvell,mv88e6190
+
+  reg:
+    maxItems: 1
+
+  eeprom-length:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Set to the length of an EEPROM connected to the switch. Must be
+      set if the switch can not detect the presence and/or size of a connected
+      EEPROM, otherwise optional.
+
+  reset-gpios:
+    description:
+      GPIO to be used to reset the whole device
+    maxItems: 1
+
+  interrupts:
+    description: The switch provides an external interrupt line, but it is
+      not always used by target systems.
+    maxItems: 1
+
+  interrupt-controller:
+    description: The switch has an internal interrupt controller used by
+      the different sub-blocks.
+
+  '#interrupt-cells':
+    description: The internal interrupt controller only supports triggering
+      on active high level interrupts so the second cell must alway be set to
+      IRQ_TYPE_LEVEL_HIGH.
+    const: 2
+
+  mdio:
+    $ref: /schemas/net/mdio.yaml#
+    unevaluatedProperties: false
+    description: Marvell MV88E6xxx switches have an varying combination of
+      internal and external MDIO buses, in some cases a combined bus that
+      can be used both internally and externally. This node is for the
+      primary bus, used internally and sometimes also externally.
+
+  mdio-external:
+    $ref: /schemas/net/mdio.yaml#
+    unevaluatedProperties: false
+    description: Marvell MV88E6xxx switches that have a separate external
+      MDIO bus use this port to access external components on the MDIO bus.
+
+    properties:
+      compatible:
+        const: marvell,mv88e6xxx-mdio-external
+
+    required:
+      - compatible
+
+allOf:
+  - $ref: dsa.yaml#/$defs/ethernet-ports
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ethernet-switch@0 {
+            compatible = "marvell,mv88e6085";
+            reg = <0>;
+            reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+
+            mdio {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                sw_phy0: ethernet-phy@0 {
+                    reg = <0x0>;
+                };
+
+                sw_phy1: ethernet-phy@1 {
+                    reg = <0x1>;
+                };
+
+                sw_phy2: ethernet-phy@2 {
+                    reg = <0x2>;
+                };
+
+                sw_phy3: ethernet-phy@3 {
+                    reg = <0x3>;
+                };
+            };
+
+            ethernet-ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                ethernet-port@0 {
+                    reg = <0>;
+                    label = "lan4";
+                    phy-handle = <&sw_phy0>;
+                    phy-mode = "internal";
+                };
+
+                ethernet-port@1 {
+                    reg = <1>;
+                    label = "lan3";
+                    phy-handle = <&sw_phy1>;
+                    phy-mode = "internal";
+                };
+
+                ethernet-port@2 {
+                    reg = <2>;
+                    label = "lan2";
+                    phy-handle = <&sw_phy2>;
+                    phy-mode = "internal";
+                };
+
+                ethernet-port@3 {
+                    reg = <3>;
+                    label = "lan1";
+                    phy-handle = <&sw_phy3>;
+                    phy-mode = "internal";
+                };
+
+                ethernet-port@5 {
+                    reg = <5>;
+                    ethernet = <&fec>;
+                    phy-mode = "rgmii-id";
+
+                    fixed-link {
+                        speed = <1000>;
+                        full-duplex;
+                    };
+                };
+            };
+        };
+    };
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ethernet-switch@0 {
+            compatible = "marvell,mv88e6190";
+            #interrupt-cells = <2>;
+            interrupt-controller;
+            interrupt-parent = <&gpio1>;
+            interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+            pinctrl-0 = <&switch_interrupt_pins>;
+            pinctrl-names = "default";
+            reg = <0>;
+
+            mdio {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                switch0phy1: ethernet-phy@1 {
+                    reg = <0x1>;
+                };
+
+                switch0phy2: ethernet-phy@2 {
+                    reg = <0x2>;
+                };
+
+                switch0phy3: ethernet-phy@3 {
+                    reg = <0x3>;
+                };
+
+                switch0phy4: ethernet-phy@4 {
+                    reg = <0x4>;
+                };
+
+                switch0phy5: ethernet-phy@5 {
+                    reg = <0x5>;
+                };
+
+                switch0phy6: ethernet-phy@6 {
+                    reg = <0x6>;
+                };
+
+                switch0phy7: ethernet-phy@7 {
+                    reg = <0x7>;
+                };
+
+                switch0phy8: ethernet-phy@8 {
+                    reg = <0x8>;
+                };
+            };
+
+            mdio-external {
+                compatible = "marvell,mv88e6xxx-mdio-external";
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                phy1: ethernet-phy@b {
+                    reg = <0xb>;
+                    compatible = "ethernet-phy-ieee802.3-c45";
+                };
+
+                phy2: ethernet-phy@c {
+                    reg = <0xc>;
+                    compatible = "ethernet-phy-ieee802.3-c45";
+                };
+            };
+
+            ethernet-ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                ethernet-port@0 {
+                    ethernet = <&eth0>;
+                    phy-mode = "rgmii";
+                    reg = <0>;
+
+                    fixed-link {
+                        full-duplex;
+                        pause;
+                        speed = <1000>;
+                    };
+                };
+
+                ethernet-port@1 {
+                    label = "lan1";
+                    phy-handle = <&switch0phy1>;
+                    reg = <1>;
+                };
+
+                ethernet-port@2 {
+                    label = "lan2";
+                    phy-handle = <&switch0phy2>;
+                    reg = <2>;
+                };
+
+                ethernet-port@3 {
+                    label = "lan3";
+                    phy-handle = <&switch0phy3>;
+                    reg = <3>;
+                };
+
+                ethernet-port@4 {
+                    label = "lan4";
+                    phy-handle = <&switch0phy4>;
+                    reg = <4>;
+                };
+
+                ethernet-port@5 {
+                    label = "lan5";
+                    phy-handle = <&switch0phy5>;
+                    reg = <5>;
+                };
+
+                ethernet-port@6 {
+                    label = "lan6";
+                    phy-handle = <&switch0phy6>;
+                    reg = <6>;
+                };
+
+                ethernet-port@7 {
+                    label = "lan7";
+                    phy-handle = <&switch0phy7>;
+                    reg = <7>;
+                };
+
+                ethernet-port@8 {
+                    label = "lan8";
+                    phy-handle = <&switch0phy8>;
+                    reg = <8>;
+                };
+
+                ethernet-port@9 {
+                    /* 88X3310P external phy */
+                    label = "lan9";
+                    phy-handle = <&phy1>;
+                    phy-mode = "xaui";
+                    reg = <9>;
+                };
+
+                ethernet-port@a {
+                    /* 88X3310P external phy */
+                    label = "lan10";
+                    phy-handle = <&phy2>;
+                    phy-mode = "xaui";
+                    reg = <0xa>;
+                };
+            };
+        };
+    };
diff --git a/Bindings/net/dsa/marvell.txt b/Bindings/net/dsa/marvell.txt
deleted file mode 100644
index 6ec0c18..0000000
--- a/Bindings/net/dsa/marvell.txt
+++ /dev/null
@@ -1,109 +0,0 @@
-Marvell DSA Switch Device Tree Bindings
----------------------------------------
-
-WARNING: This binding is currently unstable. Do not program it into a
-FLASH never to be changed again. Once this binding is stable, this
-warning will be removed.
-
-If you need a stable binding, use the old dsa.txt binding.
-
-Marvell Switches are MDIO devices. The following properties should be
-placed as a child node of an mdio device.
-
-The properties described here are those specific to Marvell devices.
-Additional required and optional properties can be found in dsa.txt.
-
-The compatibility string is used only to find an identification register,
-which is at a different MDIO base address in different switch families.
-- "marvell,mv88e6085"	: Switch has base address 0x10. Use with models:
-			  6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165,
-			  6171, 6172, 6175, 6176, 6185, 6240, 6320, 6321,
-			  6341, 6350, 6351, 6352
-- "marvell,mv88e6190"	: Switch has base address 0x00. Use with models:
-			  6190, 6190X, 6191, 6290, 6361, 6390, 6390X
-- "marvell,mv88e6250"	: Switch has base address 0x08 or 0x18. Use with model:
-			  6220, 6250
-
-Required properties:
-- compatible		: Should be one of "marvell,mv88e6085",
-			  "marvell,mv88e6190" or "marvell,mv88e6250" as
-			  indicated above
-- reg			: Address on the MII bus for the switch.
-
-Optional properties:
-
-- reset-gpios		: Should be a gpio specifier for a reset line
-- interrupts		: Interrupt from the switch
-- interrupt-controller	: Indicates the switch is itself an interrupt
-			  controller. This is used for the PHY interrupts.
-#interrupt-cells = <2>	: Controller uses two cells, number and flag
-- eeprom-length		: Set to the length of an EEPROM connected to the
-			  switch. Must be set if the switch can not detect
-			  the presence and/or size of a connected EEPROM,
-			  otherwise optional.
-- mdio			: Container of PHY and devices on the switches MDIO
-			  bus.
-- mdio?		: Container of PHYs and devices on the external MDIO
-			  bus. The node must contains a compatible string of
-			  "marvell,mv88e6xxx-mdio-external"
-
-Example:
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interrupt-parent = <&gpio0>;
-		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-
-		switch0: switch@0 {
-			compatible = "marvell,mv88e6085";
-			reg = <0>;
-			reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				switch1phy0: switch1phy0@0 {
-					reg = <0>;
-					interrupt-parent = <&switch0>;
-					interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
-				};
-			};
-		};
-	};
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interrupt-parent = <&gpio0>;
-		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-
-		switch0: switch@0 {
-			compatible = "marvell,mv88e6190";
-			reg = <0>;
-			reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				switch1phy0: switch1phy0@0 {
-					reg = <0>;
-					interrupt-parent = <&switch0>;
-					interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
-				};
-			};
-
-			mdio1 {
-				compatible = "marvell,mv88e6xxx-mdio-external";
-				#address-cells = <1>;
-				#size-cells = <0>;
-				switch1phy9: switch1phy0@9 {
-					reg = <9>;
-				};
-			};
-		};
-	};
diff --git a/Bindings/net/dsa/microchip,ksz.yaml b/Bindings/net/dsa/microchip,ksz.yaml
index b3029c6..c963dc0 100644
--- a/Bindings/net/dsa/microchip,ksz.yaml
+++ b/Bindings/net/dsa/microchip,ksz.yaml
@@ -11,7 +11,6 @@
   - Woojung Huh <Woojung.Huh@microchip.com>
 
 allOf:
-  - $ref: dsa.yaml#/$defs/ethernet-ports
   - $ref: /schemas/spi/spi-peripheral-props.yaml#
 
 properties:
@@ -78,6 +77,39 @@
   - compatible
   - reg
 
+if:
+  not:
+    properties:
+      compatible:
+        enum:
+          - microchip,ksz8863
+          - microchip,ksz8873
+then:
+  $ref: dsa.yaml#/$defs/ethernet-ports
+else:
+  patternProperties:
+    "^(ethernet-)?ports$":
+      patternProperties:
+        "^(ethernet-)?port@[0-2]$":
+          $ref: dsa-port.yaml#
+          unevaluatedProperties: false
+          properties:
+            microchip,rmii-clk-internal:
+              $ref: /schemas/types.yaml#/definitions/flag
+              description:
+                When ksz88x3 is acting as clock provier (via REFCLKO) it
+                can select between internal and external RMII reference
+                clock. Internal reference clock means that the clock for
+                the RMII of ksz88x3 is provided by the ksz88x3 internally
+                and the REFCLKI pin is unconnected. For the external
+                reference clock, the clock needs to be fed back to ksz88x3
+                via REFCLKI.
+                If microchip,rmii-clk-internal is set, ksz88x3 will provide
+                rmii reference clock internally, otherwise reference clock
+                should be provided externally.
+          dependencies:
+            microchip,rmii-clk-internal: [ethernet]
+
 unevaluatedProperties: false
 
 examples:
diff --git a/Bindings/net/ethernet-switch.yaml b/Bindings/net/ethernet-switch.yaml
index 72ac67c..b3b7e1a 100644
--- a/Bindings/net/ethernet-switch.yaml
+++ b/Bindings/net/ethernet-switch.yaml
@@ -20,9 +20,26 @@
 
 select: false
 
-properties:
-  $nodename:
-    pattern: "^(ethernet-)?switch(@.*)?$"
+allOf:
+  # This condition is here to satisfy the case where certain device
+  # nodes have to preserve non-standard names because of
+  # backward-compatibility with boot loaders inspecting certain
+  # node names.
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - marvell,turris-mox-mv88e6085
+              - marvell,turris-mox-mv88e6190
+    then:
+      properties:
+        $nodename:
+          pattern: "switch[0-3]@[0-3]+$"
+    else:
+      properties:
+        $nodename:
+          pattern: "^(ethernet-)?switch(@.*)?$"
 
 patternProperties:
   "^(ethernet-)?ports$":
diff --git a/Bindings/net/lantiq,pef2256.yaml b/Bindings/net/lantiq,pef2256.yaml
new file mode 100644
index 0000000..7da8370
--- /dev/null
+++ b/Bindings/net/lantiq,pef2256.yaml
@@ -0,0 +1,213 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/lantiq,pef2256.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lantiq PEF2256
+
+maintainers:
+  - Herve Codina <herve.codina@bootlin.com>
+
+description:
+  The Lantiq PEF2256, also known as Infineon PEF2256 or FALC56, is a framer and
+  line interface component designed to fulfill all required interfacing between
+  an analog E1/T1/J1 line and the digital PCM system highway/H.100 bus.
+
+properties:
+  compatible:
+    items:
+      - const: lantiq,pef2256
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Master Clock
+      - description: System Clock Receive
+      - description: System Clock Transmit
+
+  clock-names:
+    items:
+      - const: mclk
+      - const: sclkr
+      - const: sclkx
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    description:
+      GPIO used to reset the device.
+    maxItems: 1
+
+  pinctrl:
+    $ref: /schemas/pinctrl/pinctrl.yaml#
+    additionalProperties: false
+
+    patternProperties:
+      '-pins$':
+        type: object
+        $ref: /schemas/pinctrl/pinmux-node.yaml#
+        additionalProperties: false
+
+        properties:
+          pins:
+            enum: [ RPA, RPB, RPC, RPD, XPA, XPB, XPC, XPD ]
+
+          function:
+            enum: [ SYPR, RFM, RFMB, RSIGM, RSIG, DLR, FREEZE, RFSP, LOS,
+                    SYPX, XFMS, XSIG, TCLK, XMFB, XSIGM, DLX, XCLK, XLT,
+                    GPI, GPOH, GPOL ]
+
+        required:
+          - pins
+          - function
+
+  lantiq,data-rate-bps:
+    enum: [2048000, 4096000, 8192000, 16384000]
+    default: 2048000
+    description:
+      Data rate (bit per seconds) on the system highway.
+
+  lantiq,clock-falling-edge:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Data is sent on falling edge of the clock (and received on the rising
+      edge). If 'clock-falling-edge' is not present, data is sent on the
+      rising edge (and received on the falling edge).
+
+  lantiq,channel-phase:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1, 2, 3, 4, 5, 6, 7]
+    default: 0
+    description: |
+      The pef2256 delivers a full frame (32 8-bit time-slots in E1 and 24 8-bit
+      time-slots 8 8-bit signaling in E1/J1) every 125us. This lead to a data
+      rate of 2048000 bit/s. When lantiq,data-rate-bps is more than 2048000
+      bit/s, the data (all 32 8-bit) present in the frame are interleave with
+      unused time-slots. The lantiq,channel-phase property allows to set the
+      correct alignment of the interleave mechanism.
+      For instance, suppose lantiq,data-rate-bps = 8192000 (ie 4*2048000), and
+      lantiq,channel-phase = 2, the interleave schema with unused time-slots
+      (nu) and used time-slots (XX) for TSi is
+        nu nu XX nu nu nu XX nu nu nu XX nu
+        <-- TSi --> <- TSi+1 -> <- TSi+2 ->
+      With lantiq,data-rate-bps = 8192000, and lantiq,channel-phase = 1, the
+      interleave schema is
+        nu XX nu nu nu XX nu nu nu XX nu nu
+        <-- TSi --> <- TSi+1 -> <- TSi+2 ->
+      With lantiq,data-rate-bps = 4096000 (ie 2*2048000), and
+      lantiq,channel-phase = 1, the interleave schema is
+        nu    XX    nu    XX    nu    XX
+        <-- TSi --> <- TSi+1 -> <- TSi+2 ->
+
+patternProperties:
+  '^codec(-([0-9]|[1-2][0-9]|3[0-1]))?$':
+    type: object
+    $ref: /schemas/sound/dai-common.yaml
+    unevaluatedProperties: false
+    description:
+      Codec provided by the pef2256. This codec allows to use some of the PCM
+      system highway time-slots as audio channels to transport audio data over
+      the E1/T1/J1 lines.
+      The time-slots used by the codec must be set and so, the properties
+      'dai-tdm-slot-num', 'dai-tdm-slot-width', 'dai-tdm-slot-tx-mask' and
+      'dai-tdm-slot-rx-mask' must be present in the sound card node for
+      sub-nodes that involve the codec. The codec uses 8-bit time-slots.
+      'dai-tdm-tdm-slot-with' must be set to 8.
+      The tx and rx masks define the pef2256 time-slots assigned to the codec.
+
+    properties:
+      compatible:
+        const: lantiq,pef2256-codec
+
+      '#sound-dai-cells':
+        const: 0
+
+    required:
+      - compatible
+      - '#sound-dai-cells'
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    pef2256: framer@2000000 {
+      compatible = "lantiq,pef2256";
+      reg = <0x2000000 0x100>;
+      interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+      interrupt-parent = <&intc>;
+      clocks = <&clk_mclk>, <&clk_sclkr>, <&clk_sclkx>;
+      clock-names = "mclk", "sclkr", "sclkx";
+      reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+      lantiq,data-rate-bps = <4096000>;
+
+      pinctrl {
+        pef2256_rpa_sypr: rpa-pins {
+          pins = "RPA";
+          function = "SYPR";
+        };
+        pef2256_xpa_sypx: xpa-pins {
+          pins = "XPA";
+          function = "SYPX";
+        };
+      };
+
+      pef2256_codec0: codec-0 {
+        compatible = "lantiq,pef2256-codec";
+        #sound-dai-cells = <0>;
+        sound-name-prefix = "PEF2256_0";
+      };
+
+      pef2256_codec1: codec-1 {
+        compatible = "lantiq,pef2256-codec";
+        #sound-dai-cells = <0>;
+        sound-name-prefix = "PEF2256_1";
+      };
+    };
+
+    sound {
+      compatible = "simple-audio-card";
+      #address-cells = <1>;
+      #size-cells = <0>;
+      simple-audio-card,dai-link@0 { /* CPU DAI1 - pef2256 codec 1 */
+        reg = <0>;
+        cpu {
+          sound-dai = <&cpu_dai1>;
+        };
+        codec {
+          sound-dai = <&pef2256_codec0>;
+          dai-tdm-slot-num = <4>;
+          dai-tdm-slot-width = <8>;
+          /* TS 1, 2, 3, 4 */
+          dai-tdm-slot-tx-mask = <0 1 1 1 1>;
+          dai-tdm-slot-rx-mask = <0 1 1 1 1>;
+        };
+      };
+      simple-audio-card,dai-link@1 { /* CPU DAI2 - pef2256 codec 2 */
+        reg = <1>;
+        cpu {
+          sound-dai = <&cpu_dai2>;
+        };
+        codec {
+          sound-dai = <&pef2256_codec1>;
+          dai-tdm-slot-num = <4>;
+          dai-tdm-slot-width = <8>;
+          /* TS 5, 6, 7, 8 */
+          dai-tdm-slot-tx-mask = <0 0 0 0 0 1 1 1 1>;
+          dai-tdm-slot-rx-mask = <0 0 0 0 0 1 1 1 1>;
+        };
+      };
+    };
diff --git a/Bindings/net/marvell,aquantia.yaml b/Bindings/net/marvell,aquantia.yaml
new file mode 100644
index 0000000..9854fab
--- /dev/null
+++ b/Bindings/net/marvell,aquantia.yaml
@@ -0,0 +1,116 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/marvell,aquantia.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell Aquantia Ethernet PHY
+
+maintainers:
+  - Christian Marangi <ansuelsmth@gmail.com>
+
+description: |
+  Marvell Aquantia Ethernet PHY require a firmware to be loaded to actually
+  work.
+
+  This can be done and is implemented by OEM in 3 different way:
+    - Attached SPI flash directly to the PHY with the firmware. The PHY
+      will self load the firmware in the presence of this configuration.
+    - Read from a dedicated partition on system NAND declared in an
+      NVMEM cell, and loaded to the PHY using its mailbox interface.
+    - Manually provided firmware loaded from a file in the filesystem.
+
+allOf:
+  - $ref: ethernet-phy.yaml#
+
+select:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - ethernet-phy-id03a1.b445
+          - ethernet-phy-id03a1.b460
+          - ethernet-phy-id03a1.b4a2
+          - ethernet-phy-id03a1.b4d0
+          - ethernet-phy-id03a1.b4e0
+          - ethernet-phy-id03a1.b5c2
+          - ethernet-phy-id03a1.b4b0
+          - ethernet-phy-id03a1.b662
+          - ethernet-phy-id03a1.b712
+          - ethernet-phy-id31c3.1c12
+  required:
+    - compatible
+
+properties:
+  reg:
+    maxItems: 1
+
+  firmware-name:
+    description: specify the name of PHY firmware to load
+
+  nvmem-cells:
+    description: phandle to the firmware nvmem cell
+    maxItems: 1
+
+  nvmem-cell-names:
+    const: firmware
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    mdio {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ethernet-phy@0 {
+            compatible = "ethernet-phy-id31c3.1c12",
+                         "ethernet-phy-ieee802.3-c45";
+
+            reg = <0>;
+            firmware-name = "AQR-G4_v5.4.C-AQR_CIG_WF-1945_0x8_ID44776_VER1630.cld";
+        };
+
+        ethernet-phy@1 {
+            compatible = "ethernet-phy-id31c3.1c12",
+                         "ethernet-phy-ieee802.3-c45";
+
+            reg = <1>;
+            nvmem-cells = <&aqr_fw>;
+            nvmem-cell-names = "firmware";
+        };
+    };
+
+    flash {
+        compatible = "jedec,spi-nor";
+        #address-cells = <1>;
+        #size-cells = <1>;
+
+        partitions {
+            compatible = "fixed-partitions";
+            #address-cells = <1>;
+            #size-cells = <1>;
+
+            /* ... */
+
+            partition@650000 {
+                compatible = "nvmem-cells";
+                label = "0:ethphyfw";
+                reg = <0x650000 0x80000>;
+                read-only;
+                #address-cells = <1>;
+                #size-cells = <1>;
+
+                aqr_fw: aqr_fw@0 {
+                    reg = <0x0 0x5f42a>;
+                };
+            };
+
+            /* ... */
+
+        };
+    };
diff --git a/Bindings/net/marvell,mvusb.yaml b/Bindings/net/marvell,mvusb.yaml
index 3a33251..ab838c1 100644
--- a/Bindings/net/marvell,mvusb.yaml
+++ b/Bindings/net/marvell,mvusb.yaml
@@ -50,11 +50,14 @@
                     #address-cells = <1>;
                     #size-cells = <0>;
 
-                    switch@0 {
+                    ethernet-switch@0 {
                             compatible = "marvell,mv88e6190";
                             reg = <0x0>;
 
-                            ports {
+                            ethernet-ports {
+                                    #address-cells = <1>;
+                                    #size-cells = <0>;
+
                                     /* Port definitions */
                             };
 
diff --git a/Bindings/net/marvell,orion-mdio.yaml b/Bindings/net/marvell,orion-mdio.yaml
index e35da8b..7342985 100644
--- a/Bindings/net/marvell,orion-mdio.yaml
+++ b/Bindings/net/marvell,orion-mdio.yaml
@@ -39,28 +39,6 @@
 allOf:
   - $ref: mdio.yaml#
 
-  - if:
-      required:
-        - interrupts
-
-    then:
-      properties:
-        reg:
-          items:
-            - items:
-                - $ref: /schemas/types.yaml#/definitions/cell
-                - const: 0x84
-
-    else:
-      properties:
-        reg:
-          items:
-            - items:
-                - $ref: /schemas/types.yaml#/definitions/cell
-                - enum:
-                    - 0x4
-                    - 0x10
-
 unevaluatedProperties: false
 
 examples:
diff --git a/Bindings/net/marvell,prestera.yaml b/Bindings/net/marvell,prestera.yaml
index 5ea8b73..16ff892 100644
--- a/Bindings/net/marvell,prestera.yaml
+++ b/Bindings/net/marvell,prestera.yaml
@@ -78,8 +78,8 @@
     pcie@0 {
         #address-cells = <3>;
         #size-cells = <2>;
-        ranges = <0x0 0x0 0x0 0x0 0x0 0x0>;
-        reg = <0x0 0x0 0x0 0x0 0x0 0x0>;
+        ranges = <0x02000000 0x0 0x100000 0x10000000 0x0 0x0>;
+        reg = <0x0 0x1000>;
         device_type = "pci";
 
         switch@0,0 {
diff --git a/Bindings/net/pcs/mediatek,sgmiisys.yaml b/Bindings/net/pcs/mediatek,sgmiisys.yaml
index 66a9519..1bacc0e 100644
--- a/Bindings/net/pcs/mediatek,sgmiisys.yaml
+++ b/Bindings/net/pcs/mediatek,sgmiisys.yaml
@@ -15,15 +15,22 @@
 
 properties:
   compatible:
-    items:
-      - enum:
-          - mediatek,mt7622-sgmiisys
-          - mediatek,mt7629-sgmiisys
-          - mediatek,mt7981-sgmiisys_0
-          - mediatek,mt7981-sgmiisys_1
-          - mediatek,mt7986-sgmiisys_0
-          - mediatek,mt7986-sgmiisys_1
-      - const: syscon
+    oneOf:
+      - items:
+          - enum:
+              - mediatek,mt7622-sgmiisys
+              - mediatek,mt7629-sgmiisys
+              - mediatek,mt7981-sgmiisys_0
+              - mediatek,mt7981-sgmiisys_1
+              - mediatek,mt7986-sgmiisys_0
+              - mediatek,mt7986-sgmiisys_1
+          - const: syscon
+      - items:
+          - enum:
+              - mediatek,mt7988-sgmiisys0
+              - mediatek,mt7988-sgmiisys1
+          - const: simple-mfd
+          - const: syscon
 
   reg:
     maxItems: 1
@@ -35,11 +42,51 @@
     description: Invert polarity of the SGMII data lanes
     type: boolean
 
+  pcs:
+    type: object
+    description: MediaTek LynxI HSGMII PCS
+    properties:
+      compatible:
+        const: mediatek,mt7988-sgmii
+
+      clocks:
+        maxItems: 3
+
+      clock-names:
+        items:
+          - const: sgmii_sel
+          - const: sgmii_tx
+          - const: sgmii_rx
+
+    required:
+      - compatible
+      - clocks
+      - clock-names
+
+    additionalProperties: false
+
 required:
   - compatible
   - reg
   - '#clock-cells'
 
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - mediatek,mt7988-sgmiisys0
+              - mediatek,mt7988-sgmiisys1
+
+    then:
+      required:
+        - pcs
+
+    else:
+      properties:
+        pcs: false
+
 additionalProperties: false
 
 examples:
diff --git a/Bindings/net/qcom,ipa.yaml b/Bindings/net/qcom,ipa.yaml
index 2d5e4ff..c302186 100644
--- a/Bindings/net/qcom,ipa.yaml
+++ b/Bindings/net/qcom,ipa.yaml
@@ -43,15 +43,21 @@
 
 properties:
   compatible:
-    enum:
-      - qcom,msm8998-ipa
-      - qcom,sc7180-ipa
-      - qcom,sc7280-ipa
-      - qcom,sdm845-ipa
-      - qcom,sdx55-ipa
-      - qcom,sdx65-ipa
-      - qcom,sm6350-ipa
-      - qcom,sm8350-ipa
+    oneOf:
+      - enum:
+          - qcom,msm8998-ipa
+          - qcom,sc7180-ipa
+          - qcom,sc7280-ipa
+          - qcom,sdm845-ipa
+          - qcom,sdx55-ipa
+          - qcom,sdx65-ipa
+          - qcom,sm6350-ipa
+          - qcom,sm8350-ipa
+          - qcom,sm8550-ipa
+      - items:
+          - enum:
+              - qcom,sm8650-ipa
+          - const: qcom,sm8550-ipa
 
   reg:
     items:
diff --git a/Bindings/net/renesas,etheravb.yaml b/Bindings/net/renesas,etheravb.yaml
index 5d074f2..890f785 100644
--- a/Bindings/net/renesas,etheravb.yaml
+++ b/Bindings/net/renesas,etheravb.yaml
@@ -55,9 +55,10 @@
 
       - items:
           - enum:
-              - renesas,r9a07g043-gbeth # RZ/G2UL
+              - renesas,r9a07g043-gbeth # RZ/G2UL and RZ/Five
               - renesas,r9a07g044-gbeth # RZ/G2{L,LC}
               - renesas,r9a07g054-gbeth # RZ/V2L
+              - renesas,r9a08g045-gbeth # RZ/G3S
           - const: renesas,rzg2l-gbeth  # RZ/{G2L,G2UL,V2L} family
 
   reg: true
diff --git a/Bindings/net/renesas,ethertsn.yaml b/Bindings/net/renesas,ethertsn.yaml
new file mode 100644
index 0000000..ea35d19
--- /dev/null
+++ b/Bindings/net/renesas,ethertsn.yaml
@@ -0,0 +1,135 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/renesas,ethertsn.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas Ethernet TSN End-station
+
+maintainers:
+  - Niklas Söderlund <niklas.soderlund@ragnatech.se>
+
+description:
+  The RTSN device provides Ethernet network using a 10 Mbps, 100 Mbps, or 1
+  Gbps full-duplex link via MII/GMII/RMII/RGMII. Depending on the connected PHY.
+
+allOf:
+  - $ref: ethernet-controller.yaml#
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - renesas,r8a779g0-ethertsn       # R-Car V4H
+      - const: renesas,rcar-gen4-ethertsn
+
+  reg:
+    items:
+      - description: TSN End Station target
+      - description: generalized Precision Time Protocol target
+
+  reg-names:
+    items:
+      - const: tsnes
+      - const: gptp
+
+  interrupts:
+    items:
+      - description: TX data interrupt
+      - description: RX data interrupt
+
+  interrupt-names:
+    items:
+      - const: tx
+      - const: rx
+
+  clocks:
+    maxItems: 1
+
+  power-domains:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  phy-mode:
+    contains:
+      enum:
+        - mii
+        - rgmii
+
+  phy-handle:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Specifies a reference to a node representing a PHY device.
+
+  rx-internal-delay-ps:
+    enum: [0, 1800]
+    default: 0
+
+  tx-internal-delay-ps:
+    enum: [0, 2000]
+    default: 0
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+patternProperties:
+  "^ethernet-phy@[0-9a-f]$":
+    type: object
+    $ref: ethernet-phy.yaml#
+    unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - interrupt-names
+  - clocks
+  - power-domains
+  - resets
+  - phy-mode
+  - phy-handle
+  - '#address-cells'
+  - '#size-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/r8a779g0-cpg-mssr.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/r8a779g0-sysc.h>
+    #include <dt-bindings/gpio/gpio.h>
+
+    tsn0: ethernet@e6460000 {
+        compatible = "renesas,r8a779g0-ethertsn", "renesas,rcar-gen4-ethertsn";
+        reg = <0xe6460000 0x7000>,
+              <0xe6449000 0x500>;
+        reg-names = "tsnes", "gptp";
+        interrupts = <GIC_SPI 429 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 430 IRQ_TYPE_LEVEL_HIGH>;
+        interrupt-names = "tx", "rx";
+        clocks = <&cpg CPG_MOD 2723>;
+        power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+        resets = <&cpg 2723>;
+
+        phy-mode = "rgmii";
+        tx-internal-delay-ps = <2000>;
+        phy-handle = <&phy3>;
+
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        phy3: ethernet-phy@3 {
+            compatible = "ethernet-phy-ieee802.3-c45";
+            reg = <0>;
+            interrupt-parent = <&gpio4>;
+            interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+            reset-gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
+        };
+    };
diff --git a/Bindings/net/sff,sfp.yaml b/Bindings/net/sff,sfp.yaml
index 973e478..bf6cbc7 100644
--- a/Bindings/net/sff,sfp.yaml
+++ b/Bindings/net/sff,sfp.yaml
@@ -120,7 +120,7 @@
       pinctrl-names = "default";
       pinctrl-0 = <&cps_sfpp0_pins>;
       tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>;
-      tx-fault-gpios  = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>;
+      tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>;
     };
 
     mdio {
diff --git a/Bindings/net/xlnx,axi-ethernet.yaml b/Bindings/net/xlnx,axi-ethernet.yaml
index 1d33d80..bbe89ea 100644
--- a/Bindings/net/xlnx,axi-ethernet.yaml
+++ b/Bindings/net/xlnx,axi-ethernet.yaml
@@ -122,6 +122,20 @@
       and "phy-handle" should point to an external PHY if exists.
     maxItems: 1
 
+  dmas:
+    minItems: 2
+    maxItems: 32
+    description: TX and RX DMA channel phandle
+
+  dma-names:
+    items:
+      pattern: "^[tr]x_chan([0-9]|1[0-5])$"
+    description:
+      Should be "tx_chan0", "tx_chan1" ... "tx_chan15" for DMA Tx channel
+      Should be "rx_chan0", "rx_chan1" ... "rx_chan15" for DMA Rx channel
+    minItems: 2
+    maxItems: 32
+
 required:
   - compatible
   - interrupts
@@ -143,6 +157,8 @@
         clocks = <&axi_clk>, <&axi_clk>, <&pl_enet_ref_clk>, <&mgt_clk>;
         phy-mode = "mii";
         reg = <0x40c00000 0x40000>,<0x50c00000 0x40000>;
+        dmas = <&xilinx_dma 0>, <&xilinx_dma 1>;
+        dma-names = "tx_chan0", "rx_chan0";
         xlnx,rxcsum = <0x2>;
         xlnx,rxmem = <0x800>;
         xlnx,txcsum = <0x2>;