| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (C) 2014 Wandboard |
| * Author: Tungyi Lin <tungyilin1127@gmail.com> |
| * Richard Hu <hakahu@gmail.com> |
| */ |
| |
| #include <config.h> |
| #include <init.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch/imx-regs.h> |
| #include <asm/arch/iomux.h> |
| #include <asm/arch/mx6-pins.h> |
| #include <linux/delay.h> |
| #include <linux/errno.h> |
| #include <asm/gpio.h> |
| #include <asm/mach-imx/iomux-v3.h> |
| #include <asm/mach-imx/video.h> |
| #include <mmc.h> |
| #include <fsl_esdhc_imx.h> |
| #include <asm/arch/crm_regs.h> |
| #include <asm/io.h> |
| #include <asm/arch/sys_proto.h> |
| #include <spl.h> |
| |
| #include <asm/arch/mx6-ddr.h> |
| /* |
| * Driving strength: |
| * 0x30 == 40 Ohm |
| * 0x28 == 48 Ohm |
| */ |
| |
| #define IMX6DQ_DRIVE_STRENGTH 0x30 |
| #define IMX6SDL_DRIVE_STRENGTH 0x28 |
| #define IMX6QP_DRIVE_STRENGTH 0x28 |
| |
| /* configure MX6Q/DUAL mmdc DDR io registers */ |
| static struct mx6dq_iomux_ddr_regs mx6dq_ddr_ioregs = { |
| .dram_sdclk_0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdclk_1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_cas = IMX6DQ_DRIVE_STRENGTH, |
| .dram_ras = IMX6DQ_DRIVE_STRENGTH, |
| .dram_reset = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdcke0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdcke1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdba2 = 0x00000000, |
| .dram_sdodt0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdodt1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs2 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs3 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs4 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs5 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs6 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs7 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm2 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm3 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm4 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm5 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm6 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm7 = IMX6DQ_DRIVE_STRENGTH, |
| }; |
| |
| /* configure MX6QP mmdc DDR io registers */ |
| static struct mx6dq_iomux_ddr_regs mx6qp_ddr_ioregs = { |
| .dram_sdclk_0 = IMX6QP_DRIVE_STRENGTH, |
| .dram_sdclk_1 = IMX6QP_DRIVE_STRENGTH, |
| .dram_cas = IMX6QP_DRIVE_STRENGTH, |
| .dram_ras = IMX6QP_DRIVE_STRENGTH, |
| .dram_reset = IMX6QP_DRIVE_STRENGTH, |
| .dram_sdcke0 = IMX6QP_DRIVE_STRENGTH, |
| .dram_sdcke1 = IMX6QP_DRIVE_STRENGTH, |
| .dram_sdba2 = 0x00000000, |
| .dram_sdodt0 = IMX6QP_DRIVE_STRENGTH, |
| .dram_sdodt1 = IMX6QP_DRIVE_STRENGTH, |
| .dram_sdqs0 = IMX6QP_DRIVE_STRENGTH, |
| .dram_sdqs1 = IMX6QP_DRIVE_STRENGTH, |
| .dram_sdqs2 = IMX6QP_DRIVE_STRENGTH, |
| .dram_sdqs3 = IMX6QP_DRIVE_STRENGTH, |
| .dram_sdqs4 = IMX6QP_DRIVE_STRENGTH, |
| .dram_sdqs5 = IMX6QP_DRIVE_STRENGTH, |
| .dram_sdqs6 = IMX6QP_DRIVE_STRENGTH, |
| .dram_sdqs7 = IMX6QP_DRIVE_STRENGTH, |
| .dram_dqm0 = IMX6QP_DRIVE_STRENGTH, |
| .dram_dqm1 = IMX6QP_DRIVE_STRENGTH, |
| .dram_dqm2 = IMX6QP_DRIVE_STRENGTH, |
| .dram_dqm3 = IMX6QP_DRIVE_STRENGTH, |
| .dram_dqm4 = IMX6QP_DRIVE_STRENGTH, |
| .dram_dqm5 = IMX6QP_DRIVE_STRENGTH, |
| .dram_dqm6 = IMX6QP_DRIVE_STRENGTH, |
| .dram_dqm7 = IMX6QP_DRIVE_STRENGTH, |
| }; |
| |
| /* configure MX6Q/DUAL mmdc GRP io registers */ |
| static struct mx6dq_iomux_grp_regs mx6dq_grp_ioregs = { |
| .grp_ddr_type = 0x000c0000, |
| .grp_ddrmode_ctl = 0x00020000, |
| .grp_ddrpke = 0x00000000, |
| .grp_addds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_ctlds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_ddrmode = 0x00020000, |
| .grp_b0ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b1ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b2ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b3ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b4ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b5ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b6ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b7ds = IMX6DQ_DRIVE_STRENGTH, |
| }; |
| |
| /* configure MX6QP mmdc GRP io registers */ |
| static struct mx6dq_iomux_grp_regs mx6qp_grp_ioregs = { |
| .grp_ddr_type = 0x000c0000, |
| .grp_ddrmode_ctl = 0x00020000, |
| .grp_ddrpke = 0x00000000, |
| .grp_addds = IMX6QP_DRIVE_STRENGTH, |
| .grp_ctlds = IMX6QP_DRIVE_STRENGTH, |
| .grp_ddrmode = 0x00020000, |
| .grp_b0ds = IMX6QP_DRIVE_STRENGTH, |
| .grp_b1ds = IMX6QP_DRIVE_STRENGTH, |
| .grp_b2ds = IMX6QP_DRIVE_STRENGTH, |
| .grp_b3ds = IMX6QP_DRIVE_STRENGTH, |
| .grp_b4ds = IMX6QP_DRIVE_STRENGTH, |
| .grp_b5ds = IMX6QP_DRIVE_STRENGTH, |
| .grp_b6ds = IMX6QP_DRIVE_STRENGTH, |
| .grp_b7ds = IMX6QP_DRIVE_STRENGTH, |
| }; |
| |
| /* configure MX6SOLO/DUALLITE mmdc DDR io registers */ |
| struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = { |
| .dram_sdclk_0 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdclk_1 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_cas = IMX6SDL_DRIVE_STRENGTH, |
| .dram_ras = IMX6SDL_DRIVE_STRENGTH, |
| .dram_reset = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdcke0 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdcke1 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdba2 = 0x00000000, |
| .dram_sdodt0 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdodt1 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs0 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs1 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs2 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs3 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs4 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs5 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs6 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_sdqs7 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm0 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm1 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm2 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm3 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm4 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm5 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm6 = IMX6SDL_DRIVE_STRENGTH, |
| .dram_dqm7 = IMX6SDL_DRIVE_STRENGTH, |
| }; |
| |
| /* configure MX6SOLO/DUALLITE mmdc GRP io registers */ |
| struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = { |
| .grp_ddr_type = 0x000c0000, |
| .grp_ddrmode_ctl = 0x00020000, |
| .grp_ddrpke = 0x00000000, |
| .grp_addds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_ctlds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_ddrmode = 0x00020000, |
| .grp_b0ds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_b1ds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_b2ds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_b3ds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_b4ds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_b5ds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_b6ds = IMX6SDL_DRIVE_STRENGTH, |
| .grp_b7ds = IMX6SDL_DRIVE_STRENGTH, |
| }; |
| |
| /* H5T04G63AFR-PB */ |
| static struct mx6_ddr3_cfg h5t04g63afr = { |
| .mem_speed = 1600, |
| .density = 4, |
| .width = 16, |
| .banks = 8, |
| .rowaddr = 15, |
| .coladdr = 10, |
| .pagesz = 2, |
| .trcd = 1375, |
| .trcmin = 4875, |
| .trasmin = 3500, |
| }; |
| |
| /* H5TQ2G63DFR-H9 */ |
| static struct mx6_ddr3_cfg h5tq2g63dfr = { |
| .mem_speed = 1333, |
| .density = 2, |
| .width = 16, |
| .banks = 8, |
| .rowaddr = 14, |
| .coladdr = 10, |
| .pagesz = 2, |
| .trcd = 1350, |
| .trcmin = 4950, |
| .trasmin = 3600, |
| }; |
| |
| static struct mx6_mmdc_calibration mx6q_2g_mmdc_calib = { |
| .p0_mpwldectrl0 = 0x001f001f, |
| .p0_mpwldectrl1 = 0x001f001f, |
| .p1_mpwldectrl0 = 0x001f001f, |
| .p1_mpwldectrl1 = 0x001f001f, |
| .p0_mpdgctrl0 = 0x4301030d, |
| .p0_mpdgctrl1 = 0x03020277, |
| .p1_mpdgctrl0 = 0x4300030a, |
| .p1_mpdgctrl1 = 0x02780248, |
| .p0_mprddlctl = 0x4536393b, |
| .p1_mprddlctl = 0x36353441, |
| .p0_mpwrdlctl = 0x41414743, |
| .p1_mpwrdlctl = 0x462f453f, |
| }; |
| |
| /* DDR 64bit 2GB */ |
| static struct mx6_ddr_sysinfo mem_q = { |
| .dsize = 2, |
| .cs1_mirror = 0, |
| /* config for full 4GB range so that get_mem_size() works */ |
| .cs_density = 32, |
| .ncs = 1, |
| .bi_on = 1, |
| .rtt_nom = 1, |
| .rtt_wr = 0, |
| .ralat = 5, |
| .walat = 0, |
| .mif3_mode = 3, |
| .rst_to_cke = 0x23, |
| .sde_to_rst = 0x10, |
| .refsel = 1, /* Refresh cycles at 32KHz */ |
| .refr = 3, /* 4 refresh commands per refresh cycle */ |
| }; |
| |
| static struct mx6_mmdc_calibration mx6dl_1g_mmdc_calib = { |
| .p0_mpwldectrl0 = 0x001f001f, |
| .p0_mpwldectrl1 = 0x001f001f, |
| .p1_mpwldectrl0 = 0x001f001f, |
| .p1_mpwldectrl1 = 0x001f001f, |
| .p0_mpdgctrl0 = 0x420e020e, |
| .p0_mpdgctrl1 = 0x02000200, |
| .p1_mpdgctrl0 = 0x42020202, |
| .p1_mpdgctrl1 = 0x01720172, |
| .p0_mprddlctl = 0x494c4f4c, |
| .p1_mprddlctl = 0x4a4c4c49, |
| .p0_mpwrdlctl = 0x3f3f3133, |
| .p1_mpwrdlctl = 0x39373f2e, |
| }; |
| |
| static struct mx6_mmdc_calibration mx6s_512m_mmdc_calib = { |
| .p0_mpwldectrl0 = 0x0040003c, |
| .p0_mpwldectrl1 = 0x0032003e, |
| .p0_mpdgctrl0 = 0x42350231, |
| .p0_mpdgctrl1 = 0x021a0218, |
| .p0_mprddlctl = 0x4b4b4e49, |
| .p0_mpwrdlctl = 0x3f3f3035, |
| }; |
| |
| /* DDR 64bit 1GB */ |
| static struct mx6_ddr_sysinfo mem_dl = { |
| .dsize = 2, |
| .cs1_mirror = 0, |
| /* config for full 4GB range so that get_mem_size() works */ |
| .cs_density = 32, |
| .ncs = 1, |
| .bi_on = 1, |
| .rtt_nom = 1, |
| .rtt_wr = 0, |
| .ralat = 5, |
| .walat = 0, |
| .mif3_mode = 3, |
| .rst_to_cke = 0x23, |
| .sde_to_rst = 0x10, |
| .refsel = 1, /* Refresh cycles at 32KHz */ |
| .refr = 3, /* 4 refresh commands per refresh cycle */ |
| }; |
| |
| /* DDR 32bit 512MB */ |
| static struct mx6_ddr_sysinfo mem_s = { |
| .dsize = 1, |
| .cs1_mirror = 0, |
| /* config for full 4GB range so that get_mem_size() works */ |
| .cs_density = 32, |
| .ncs = 1, |
| .bi_on = 1, |
| .rtt_nom = 1, |
| .rtt_wr = 0, |
| .ralat = 5, |
| .walat = 0, |
| .mif3_mode = 3, |
| .rst_to_cke = 0x23, |
| .sde_to_rst = 0x10, |
| .refsel = 1, /* Refresh cycles at 32KHz */ |
| .refr = 3, /* 4 refresh commands per refresh cycle */ |
| }; |
| |
| static void ccgr_init(void) |
| { |
| struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; |
| |
| writel(0x00C03F3F, &ccm->CCGR0); |
| writel(0x0030FC03, &ccm->CCGR1); |
| writel(0x0FFFC000, &ccm->CCGR2); |
| writel(0x3FF03000, &ccm->CCGR3); |
| writel(0x00FFF300, &ccm->CCGR4); |
| writel(0x0F0000C3, &ccm->CCGR5); |
| writel(0x000003FF, &ccm->CCGR6); |
| } |
| |
| static void spl_dram_init_imx6qp_lpddr3(void) |
| { |
| /* MMDC0_MDSCR set the Configuration request bit during MMDC set up */ |
| writel(0x00008000, MMDC_P0_BASE_ADDR + 0x01c); |
| /* Calibrations - ZQ */ |
| writel(0xa1390003, MMDC_P0_BASE_ADDR + 0x800); |
| /* write leveling */ |
| writel(0x00060004, MMDC_P0_BASE_ADDR + 0x80c); |
| writel(0x000B0004, MMDC_P0_BASE_ADDR + 0x810); |
| writel(0x00000004, MMDC_P1_BASE_ADDR + 0x80c); |
| writel(0x00000000, MMDC_P1_BASE_ADDR + 0x810); |
| /* |
| * DQS gating, read delay, write delay calibration values |
| * based on calibration compare of 0x00ffff00 |
| */ |
| writel(0x03040314, MMDC_P0_BASE_ADDR + 0x83c); |
| writel(0x03080300, MMDC_P0_BASE_ADDR + 0x840); |
| writel(0x03000310, MMDC_P1_BASE_ADDR + 0x83c); |
| writel(0x0268023C, MMDC_P1_BASE_ADDR + 0x840); |
| writel(0x4034363A, MMDC_P0_BASE_ADDR + 0x848); |
| writel(0x36302C3C, MMDC_P1_BASE_ADDR + 0x848); |
| writel(0x3E3E4046, MMDC_P0_BASE_ADDR + 0x850); |
| writel(0x483A4844, MMDC_P1_BASE_ADDR + 0x850); |
| writel(0x33333333, MMDC_P0_BASE_ADDR + 0x81c); |
| writel(0x33333333, MMDC_P0_BASE_ADDR + 0x820); |
| writel(0x33333333, MMDC_P0_BASE_ADDR + 0x824); |
| writel(0x33333333, MMDC_P0_BASE_ADDR + 0x828); |
| writel(0x33333333, MMDC_P1_BASE_ADDR + 0x81c); |
| writel(0x33333333, MMDC_P1_BASE_ADDR + 0x820); |
| writel(0x33333333, MMDC_P1_BASE_ADDR + 0x824); |
| writel(0x33333333, MMDC_P1_BASE_ADDR + 0x828); |
| writel(0x24912489, MMDC_P0_BASE_ADDR + 0x8c0); |
| writel(0x24914452, MMDC_P1_BASE_ADDR + 0x8c0); |
| writel(0x00000800, MMDC_P0_BASE_ADDR + 0x8b8); |
| writel(0x00000800, MMDC_P1_BASE_ADDR + 0x8b8); |
| /* MMDC init: in DDR3, 64-bit mode, only MMDC0 is initiated */ |
| writel(0x00020036, MMDC_P0_BASE_ADDR + 0x004); |
| writel(0x09444040, MMDC_P0_BASE_ADDR + 0x008); |
| writel(0x898E79A4, MMDC_P0_BASE_ADDR + 0x00c); |
| writel(0xDB538F64, MMDC_P0_BASE_ADDR + 0x010); |
| writel(0x01FF00DD, MMDC_P0_BASE_ADDR + 0x014); |
| writel(0x00011740, MMDC_P0_BASE_ADDR + 0x018); |
| writel(0x00008000, MMDC_P0_BASE_ADDR + 0x01c); |
| writel(0x000026D2, MMDC_P0_BASE_ADDR + 0x02c); |
| writel(0x008E1023, MMDC_P0_BASE_ADDR + 0x030); |
| writel(0x00000047, MMDC_P0_BASE_ADDR + 0x040); |
| writel(0x14420000, MMDC_P0_BASE_ADDR + 0x400); |
| writel(0x841A0000, MMDC_P0_BASE_ADDR + 0x000); |
| writel(0x00400c58, MMDC_P0_BASE_ADDR + 0x890); |
| /* add NOC DDR configuration */ |
| writel(0x00000000, NOC_DDR_BASE_ADDR + 0x008); |
| writel(0x2871C39B, NOC_DDR_BASE_ADDR + 0x00c); |
| writel(0x000005B4, NOC_DDR_BASE_ADDR + 0x038); |
| writel(0x00000040, NOC_DDR_BASE_ADDR + 0x014); |
| writel(0x00000020, NOC_DDR_BASE_ADDR + 0x028); |
| writel(0x00000020, NOC_DDR_BASE_ADDR + 0x02c); |
| writel(0x02088032, MMDC_P0_BASE_ADDR + 0x01c); |
| writel(0x00008033, MMDC_P0_BASE_ADDR + 0x01c); |
| writel(0x00048031, MMDC_P0_BASE_ADDR + 0x01c); |
| writel(0x19308030, MMDC_P0_BASE_ADDR + 0x01c); |
| writel(0x04008040, MMDC_P0_BASE_ADDR + 0x01c); |
| writel(0x00007800, MMDC_P0_BASE_ADDR + 0x020); |
| writel(0x00022227, MMDC_P0_BASE_ADDR + 0x818); |
| writel(0x00022227, MMDC_P1_BASE_ADDR + 0x818); |
| writel(0x00025576, MMDC_P0_BASE_ADDR + 0x004); |
| writel(0x00011006, MMDC_P0_BASE_ADDR + 0x404); |
| writel(0x00000000, MMDC_P0_BASE_ADDR + 0x01c); |
| } |
| |
| static void spl_dram_init(void) |
| { |
| if (is_mx6dqp()) { |
| mx6dq_dram_iocfg(64, &mx6qp_ddr_ioregs, &mx6qp_grp_ioregs); |
| spl_dram_init_imx6qp_lpddr3(); |
| } else if (is_cpu_type(MXC_CPU_MX6SOLO)) { |
| mx6sdl_dram_iocfg(32, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs); |
| mx6_dram_cfg(&mem_s, &mx6s_512m_mmdc_calib, &h5tq2g63dfr); |
| } else if (is_cpu_type(MXC_CPU_MX6DL)) { |
| mx6sdl_dram_iocfg(64, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs); |
| mx6_dram_cfg(&mem_dl, &mx6dl_1g_mmdc_calib, &h5tq2g63dfr); |
| } else if (is_cpu_type(MXC_CPU_MX6Q)) { |
| mx6dq_dram_iocfg(64, &mx6dq_ddr_ioregs, &mx6dq_grp_ioregs); |
| mx6_dram_cfg(&mem_q, &mx6q_2g_mmdc_calib, &h5t04g63afr); |
| } |
| |
| udelay(100); |
| } |
| |
| void board_init_f(ulong dummy) |
| { |
| ccgr_init(); |
| |
| /* setup AIPS and disable watchdog */ |
| arch_cpu_init(); |
| |
| gpr_init(); |
| |
| /* iomux */ |
| board_early_init_f(); |
| |
| /* setup GP timer */ |
| timer_init(); |
| |
| /* UART clocks enabled and gd valid - init serial console */ |
| preloader_console_init(); |
| |
| /* DDR initialization */ |
| spl_dram_init(); |
| } |
| |
| #define USDHC1_CD_GPIO IMX_GPIO_NR(1, 2) |
| #define USDHC3_CD_GPIO IMX_GPIO_NR(3, 9) |
| |
| #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ |
| PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ |
| PAD_CTL_SRE_FAST | PAD_CTL_HYS) |
| |
| static struct fsl_esdhc_cfg usdhc_cfg[2] = { |
| {USDHC3_BASE_ADDR}, |
| {USDHC1_BASE_ADDR}, |
| }; |
| |
| static iomux_v3_cfg_t const usdhc1_pads[] = { |
| IOMUX_PADS(PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| /* Carrier MicroSD Card Detect */ |
| IOMUX_PADS(PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL)), |
| }; |
| |
| static iomux_v3_cfg_t const usdhc3_pads[] = { |
| IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), |
| /* SOM MicroSD Card Detect */ |
| IOMUX_PADS(PAD_EIM_DA9__GPIO3_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL)), |
| }; |
| |
| int board_mmc_getcd(struct mmc *mmc) |
| { |
| struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; |
| int ret = 0; |
| |
| switch (cfg->esdhc_base) { |
| case USDHC1_BASE_ADDR: |
| ret = !gpio_get_value(USDHC1_CD_GPIO); |
| break; |
| case USDHC3_BASE_ADDR: |
| ret = !gpio_get_value(USDHC3_CD_GPIO); |
| break; |
| } |
| |
| return ret; |
| } |
| |
| int board_mmc_init(struct bd_info *bis) |
| { |
| int ret; |
| u32 index = 0; |
| |
| /* |
| * Following map is done: |
| * (U-Boot device node) (Physical Port) |
| * mmc0 SOM MicroSD |
| * mmc1 Carrier board MicroSD |
| */ |
| for (index = 0; index < CFG_SYS_FSL_USDHC_NUM; ++index) { |
| switch (index) { |
| case 0: |
| SETUP_IOMUX_PADS(usdhc3_pads); |
| usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); |
| usdhc_cfg[0].max_bus_width = 4; |
| gpio_direction_input(USDHC3_CD_GPIO); |
| break; |
| case 1: |
| SETUP_IOMUX_PADS(usdhc1_pads); |
| usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); |
| usdhc_cfg[1].max_bus_width = 4; |
| gpio_direction_input(USDHC1_CD_GPIO); |
| break; |
| default: |
| printf("Warning: you configured more USDHC controllers" |
| "(%d) then supported by the board (%d)\n", |
| index + 1, CFG_SYS_FSL_USDHC_NUM); |
| return -EINVAL; |
| } |
| |
| ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]); |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |