RPXlite configuration fixes
- Use correct flash sector size
- Use correct memory test end address
- Add support for bzip2 compression
- Various small fixes
Patch by Yuli Barcohen, 05 Jun 2005
diff --git a/CHANGELOG b/CHANGELOG
index e2730cf..a1a768d 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -2,6 +2,13 @@
Changes since U-Boot 1.1.4:
======================================================================
+* RPXlite configuration fixes
+ - Use correct flash sector size
+ - Use correct memory test end address
+ - Add support for bzip2 compression
+ - Various small fixes
+ Patch by Yuli Barcohen, 05 Jun 2005
+
* Memory configuration changes for ZPC.1900 board
- Fix SDRAM timing on both local bus and 60x bus
- Add support for second flash bank (SIMM)
diff --git a/include/configs/RPXlite.h b/include/configs/RPXlite.h
index 6b65031..48ada0e 100644
--- a/include/configs/RPXlite.h
+++ b/include/configs/RPXlite.h
@@ -21,10 +21,6 @@
* MA 02111-1307 USA
*/
-/*
- * board/config.h - configuration options, board specific
- */
-
/* Yoo. Jonghoon, IPone, yooth@ipone.co.kr
* U-Boot port on RPXlite board
*/
@@ -53,8 +49,6 @@
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#endif
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND \
"bootp; " \
@@ -65,6 +59,7 @@
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+#define CONFIG_BZIP2 /* Include support for bzip2 compressed images */
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
@@ -86,12 +81,14 @@
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0040000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00C0000 /* 4 ... 12 MB in DRAM */
+#define CFG_MEMTEST_START 0x00400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x00C00000 /* 4 ... 12 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_RESET_ADDRESS 0x09900000
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_LOAD_ADDR 0x400000 /* default load address */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
@@ -120,16 +117,14 @@
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFFC00000
-/*%%% #define CFG_FLASH_BASE 0xFFF00000 */
-#if defined(DEBUG) || (CONFIG_COMMANDS & CFG_CMD_IDE)
+#define CFG_FLASH_BASE 0xFFC00000
+#define CFG_MONITOR_BASE TEXT_BASE
#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#ifdef CONFIG_BZIP2
+#define CFG_MALLOC_LEN (4096 << 10) /* Reserve ~4 MB for malloc() */
#else
-#define CFG_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
-#endif
-#define CFG_MONITOR_BASE 0xFFF00000
-/*%%% #define CFG_MONITOR_BASE CFG_FLASH_BASE */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 KB for malloc() */
+#endif /* CONFIG_BZIP2 */
/*
* For booting Linux, the board info and command line data
@@ -147,9 +142,13 @@
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CFG_DIRECT_FLASH_TFTP
+
#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#define CFG_ENV_SECT_SIZE 0x40000 /* We use one complete sector */
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+
+#define CONFIG_ENV_OVERWRITE
/*-----------------------------------------------------------------------
* Cache Configuration
@@ -352,12 +351,12 @@
#define BCSR0_ENMONXCVR 0x01 /* Monitor XVCR Control */
#define BCSR0_ENNVRAM 0x02 /* CS4# Control */
-#define BCSR0_LED5 0x04 /* LED5 control 0='on' 1='off' */
-#define BCSR0_LED4 0x08 /* LED4 control 0='on' 1='off' */
+#define BCSR0_LED5 0x04 /* LED5 control 0='on' 1='off' */
+#define BCSR0_LED4 0x08 /* LED4 control 0='on' 1='off' */
#define BCSR0_FULLDPLX 0x10 /* Ethernet XCVR Control */
#define BCSR0_COLTEST 0x20
#define BCSR0_ETHLPBK 0x40
-#define BCSR0_ETHEN 0x80
+#define BCSR0_ETHEN 0x80
#define BCSR1_PCVCTL7 0x01 /* PC Slot B Control */
#define BCSR1_PCVCTL6 0x02
@@ -371,22 +370,13 @@
#define BCSR2_USBSPD 0x40
#define BCSR2_USBSUSP 0x80
-#define BCSR3_BWRTC 0x01 /* Real Time Clock Battery */
-#define BCSR3_BWNVR 0x02 /* NVRAM Battery */
+#define BCSR3_BWRTC 0x01 /* Real Time Clock Battery */
+#define BCSR3_BWNVR 0x02 /* NVRAM Battery */
#define BCSR3_RDY_BSY 0x04 /* Flash Operation */
-#define BCSR3_RPXL 0x08 /* Reserved (reads back '1') */
-#define BCSR3_D27 0x10 /* Dip Switch settings */
-#define BCSR3_D26 0x20
-#define BCSR3_D25 0x40
-#define BCSR3_D24 0x80
-
-
-/*
- * Environment setting
- */
-
-#define CONFIG_ETHADDR 00:10:EC:00:1D:0B
-#define CONFIG_IPADDR 192.168.1.65
-#define CONFIG_SERVERIP 192.168.1.27
+#define BCSR3_RPXL 0x08 /* Reserved (reads back '1') */
+#define BCSR3_D27 0x10 /* Dip Switch settings */
+#define BCSR3_D26 0x20
+#define BCSR3_D25 0x40
+#define BCSR3_D24 0x80
#endif /* __CONFIG_H */