Update for NC650 board. Add NC650 based CP850 configuration.
Signed-off-by: dzu@denx.de <dzu@denx.de>
diff --git a/CHANGELOG b/CHANGELOG
index cbc18d9..6edcd25 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -2,6 +2,11 @@
Changes since U-Boot 1.1.4:
======================================================================
+* Update for NC650 board:
+ - Support rev1 and rev2 hardware
+ - adapt to new NAND layer
+ - add CP850 configuration based on NC650
+
* MPC5200: enable snooping of DMA transactions on XLB even if no PCI
is configured; othrwise DMA accesses aren't cache coherent which
causes for example USB to fail.
diff --git a/Makefile b/Makefile
index 9b93463..249c9f0 100644
--- a/Makefile
+++ b/Makefile
@@ -633,8 +633,21 @@
}
@./mkconfig -a $(call xtract_NETTA2,$@) ppc mpc8xx netta2
-NC650_config: unconfig
- @./mkconfig $(@:_config=) ppc mpc8xx nc650
+NC650_Rev1_config \
+NC650_Rev2_config \
+CP850_config: unconfig
+ @ >include/config.h
+ @[ -z "$(findstring CP850,$@)" ] || \
+ { echo "#define CONFIG_CP850 1" >>include/config.h ; \
+ echo "#define CONFIG_IDS852_REV2 1" >>include/config.h ; \
+ }
+ @[ -z "$(findstring Rev1,$@)" ] || \
+ { echo "#define CONFIG_IDS852_REV1 1" >>include/config.h ; \
+ }
+ @[ -z "$(findstring Rev2,$@)" ] || \
+ { echo "#define CONFIG_IDS852_REV2 1" >>include/config.h ; \
+ }
+ @./mkconfig -a NC650 ppc mpc8xx nc650
NX823_config: unconfig
@./mkconfig $(@:_config=) ppc mpc8xx nx823
diff --git a/board/nc650/Makefile b/board/nc650/Makefile
index a4dd85f..8dc4934 100644
--- a/board/nc650/Makefile
+++ b/board/nc650/Makefile
@@ -1,4 +1,5 @@
#
+# (C) Copyright 2006 Detlev Zundel, dzu@denx.de
# (C) Copyright 2004
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
@@ -25,7 +26,7 @@
LIB = lib$(BOARD).a
-OBJS = $(BOARD).o flash.o
+OBJS = $(BOARD).o nand.o flash.o
$(LIB): .depend $(OBJS)
$(AR) crv $@ $(OBJS)
diff --git a/board/nc650/config.mk b/board/nc650/config.mk
index fa8ba31..5b2284a 100644
--- a/board/nc650/config.mk
+++ b/board/nc650/config.mk
@@ -1,4 +1,5 @@
#
+# (C) Copyright 2006 Detlev Zundel, dzu@denx.de
# (C) Copyright 2004
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
#
@@ -26,3 +27,4 @@
#
TEXT_BASE = 0x40700000
+BOARDLIBS = drivers/nand/libnand.a
diff --git a/board/nc650/nc650.c b/board/nc650/nc650.c
index fe96b93..c90ac9c 100644
--- a/board/nc650/nc650.c
+++ b/board/nc650/nc650.c
@@ -1,4 +1,5 @@
/*
+ * (C) Copyright 2006 Detlev Zundel, dzu@denx.de
* (C) Copyright 2001
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
@@ -108,7 +109,16 @@
int checkboard (void)
{
- puts ("Board: NC650\n");
+#if !defined(CONFIG_CP850)
+ puts ("Board: NC650");
+#else
+ puts ("Board: CP850");
+#endif
+#if defined(CONFIG_IDS852_REV1)
+ puts (" with IDS852 rev 1 module\n");
+#elif defined(CONFIG_IDS852_REV2)
+ puts (" with IDS852 rev 2 module\n");
+#endif
return 0;
}
@@ -241,13 +251,61 @@
return (get_ram_size(base, maxsize));
}
-#if (CONFIG_COMMANDS & CFG_CMD_NAND)
-void nand_init(void)
+
+#if defined(CONFIG_CP850)
+
+#define DPRAM_VARNAME "KP850DIP"
+#define PARAM_ADDR 0x7C0
+#define NAME_ADDR 0x7F8
+#define BOARD_NAME "KP01"
+#define DEFAULT_LB "241111"
+
+int misc_init_r(void)
{
- extern unsigned long nand_probe(unsigned long physadr);
+ int iCompatMode = 0;
+ char *pParam = NULL;
+ char *envlb;
+
+ /*
+ First byte in CPLD read address space signals compatibility mode
+ 0 - cp850
+ 1 - kp852
+ */
+ pParam = (char*)(CFG_CPLD_BASE);
+ if( *pParam != 0)
+ iCompatMode = 1;
+
+ if ( iCompatMode != 0) {
+ /*
+ In KP852 compatibility mode we have to write to
+ DPRAM as early as possible the binary coded
+ line config and board name.
+ The line config is derived from the environment
+ variable DPRAM_VARNAME by converting from ASCII
+ to binary per character.
+ */
+ if ( (envlb = getenv ( DPRAM_VARNAME )) == 0) {
+ setenv( DPRAM_VARNAME, DEFAULT_LB);
+ envlb = DEFAULT_LB;
+ }
+
+ /* Status string */
+ printf("Mode: KP852(LB=%s)\n", envlb);
- unsigned long totlen = nand_probe(CFG_NAND_BASE);
+ /* copy appl init */
+ pParam = (char*)(DPRAM_BASE_ADDR + PARAM_ADDR);
+ while (*envlb) {
+ *(pParam++) = *(envlb++) - '0';
+ }
+ *pParam = '\0';
- printf ("%4lu MB\n", totlen >> 20);
+ /* copy board id */
+ pParam = (char*)(DPRAM_BASE_ADDR + NAME_ADDR);
+ strcpy( pParam, BOARD_NAME);
+ } else {
+ puts("Mode: CP850\n");
+ }
+
+ return 0;
}
#endif
diff --git a/include/configs/NC650.h b/include/configs/NC650.h
index 3c59df4..8da29c4 100644
--- a/include/configs/NC650.h
+++ b/include/configs/NC650.h
@@ -1,4 +1,5 @@
/*
+ * (C) Copyright 2006 Detlev Zundel, dzu@denx.de
* (C) Copyright 2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
@@ -65,6 +66,11 @@
#define CFG_8XX_XIN CONFIG_8xx_OSCLK
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#define CONFIG_AUTOBOOT_KEYED
+#define CONFIG_AUTOBOOT_PROMPT "\nEnter password - autoboot in %d seconds...\n"
+#define CONFIG_AUTOBOOT_DELAY_STR "ids"
+#define CONFIG_BOOT_RETRY_TIME 900
+#define CONFIG_BOOT_RETRY_MIN 30
#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
@@ -75,7 +81,7 @@
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
"bootm"
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#define CONFIG_WATCHDOG /* watchdog enabled */
#undef CONFIG_STATUS_LED /* Status LED disabled */
@@ -96,12 +102,26 @@
/*
* Software (bit-bang) I2C driver configuration
*/
+#if defined(CONFIG_IDS852_REV1)
+
#define SCL 0x1000 /* PA 3 */
#define SDA 0x2000 /* PA 2 */
#define __I2C_DIR immr->im_ioport.iop_padir
#define __I2C_DAT immr->im_ioport.iop_padat
#define __I2C_PAR immr->im_ioport.iop_papar
+
+#elif defined(CONFIG_IDS852_REV2)
+
+#define SCL 0x0002 /* PB 30 */
+#define SDA 0x0001 /* PB 31 */
+
+#define __I2C_PAR immr->im_cpm.cp_pbpar
+#define __I2C_DIR immr->im_cpm.cp_pbdir
+#define __I2C_DAT immr->im_cpm.cp_pbdat
+
+#endif
+
#define I2C_INIT { __I2C_PAR &= ~(SDA|SCL); \
__I2C_DIR |= (SDA|SCL); }
#define I2C_READ ((__I2C_DAT & SDA) ? 1 : 0)
@@ -229,17 +249,6 @@
#define ADDR_COLUMN 1
#define NAND_NO_RB
-#define NAND_WAIT_READY(nand) udelay(12)
-#define WRITE_NAND_COMMAND(d, adr) WRITE_NAND(d, adr + 2)
-#define WRITE_NAND_ADDRESS(d, adr) WRITE_NAND(d, adr + 1)
-#define WRITE_NAND(d, adr) (*(volatile uint8_t *)(adr) = (uint8_t)(d))
-#define READ_NAND(adr) (*(volatile uint8_t *)(adr))
-#define NAND_DISABLE_CE(nand) /* nop */
-#define NAND_ENABLE_CE(nand) /* nop */
-#define NAND_CTL_CLRALE(nandptr) /* nop */
-#define NAND_CTL_SETALE(nandptr) /* nop */
-#define NAND_CTL_CLRCLE(nandptr) /* nop */
-#define NAND_CTL_SETCLE(nandptr) /* nop */
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
@@ -312,7 +321,8 @@
#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V)
/*
- * BR2 and OR2 (NAND Flash) - now addressed through UPMB
+ * BR2 and OR2 (NAND Flash) - addressed through UPMB on rev 1
+ * rev2 only uses the chipselect
*/
#define CFG_NAND_BASE 0x50000000
#define CFG_NAND_SIZE 0x04000000
@@ -338,6 +348,18 @@
#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V)
/*
+ * BR4 and OR4 (CPLD)
+ */
+#define CFG_CPLD_BASE 0x80000000 /* CPLD */
+#define CFG_CPLD_SIZE 0x10000 /* only 16 used */
+
+#define CFG_OR_TIMING_CPLD (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
+ OR_SCY_1_CLK)
+
+#define CFG_BR4_PRELIM ((CFG_CPLD_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
+#define CFG_OR4_PRELIM (((-CFG_CPLD_SIZE) & OR_AM_MSK) | CFG_OR_TIMING_CPLD)
+
+/*
* BR5 and OR5 (SRAM)
*/
#define CFG_SRAM_BASE 0x60000000
@@ -349,6 +371,16 @@
#define CFG_BR5_PRELIM ((CFG_SRAM_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
#define CFG_OR5_PRELIM (((-CFG_SRAM_SIZE) & OR_AM_MSK) | CFG_OR_TIMING_SRAM)
+#if defined(CONFIG_CP850)
+/*
+ * BR6 and OR6 (DPRAM) - only on CP850
+ */
+#define CFG_OR6_PRELIM 0xffff8170
+#define CFG_BR6_PRELIM 0xa0000401
+#define DPRAM_BASE_ADDR 0xa0000000
+
+#define CONFIG_MISC_INIT_R 1
+#endif
/*
* 4096 Rows from SDRAM example configuration
@@ -413,14 +445,12 @@
#define CONFIG_JFFS2_PART_OFFSET 0x00000000
/* mtdparts command line support */
-/*
#define CONFIG_JFFS2_CMDLINE
#define MTDIDS_DEFAULT "nor0=nc650-0,nand0=nc650-nand"
#define MTDPARTS_DEFAULT "mtdparts=nc650-0:1m(kernel1),1m(kernel2)," \
- "2560k(cramfs1),2560k(cramfs2)," \
- "256k(u-boot),256k(env);" \
- "nc650-nand:4m(nand1),28m(nand2)"
-*/
+ "4m(cramfs1),1m(cramfs2)," \
+ "256k(u-boot),128k(env);" \
+ "nc650-nand:4m(jffs1),28m(jffs2)"
#endif /* __CONFIG_H */