Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'
diff --git a/arch/arm/cpu/armv7/exynos/clock.c b/arch/arm/cpu/armv7/exynos/clock.c
index 36fedd6..84a5047 100644
--- a/arch/arm/cpu/armv7/exynos/clock.c
+++ b/arch/arm/cpu/armv7/exynos/clock.c
@@ -1410,7 +1410,8 @@
else {
if (proid_is_exynos4412())
exynos4x12_set_mmc_clk(dev_index, div);
- exynos4_set_mmc_clk(dev_index, div);
+ else
+ exynos4_set_mmc_clk(dev_index, div);
}
}
diff --git a/arch/arm/cpu/armv7/exynos/pinmux.c b/arch/arm/cpu/armv7/exynos/pinmux.c
index 8002bce..74cc700 100644
--- a/arch/arm/cpu/armv7/exynos/pinmux.c
+++ b/arch/arm/cpu/armv7/exynos/pinmux.c
@@ -462,7 +462,7 @@
case PERIPH_ID_SDMMC1:
case PERIPH_ID_SDMMC3:
case PERIPH_ID_SDMMC4:
- printf("SDMMC device %d not implemented\n", peripheral);
+ debug("SDMMC device %d not implemented\n", peripheral);
return -1;
default:
debug("%s: invalid peripheral %d", __func__, peripheral);
diff --git a/arch/arm/cpu/armv7/exynos/spl_boot.c b/arch/arm/cpu/armv7/exynos/spl_boot.c
index 3651c00..ade45fd 100644
--- a/arch/arm/cpu/armv7/exynos/spl_boot.c
+++ b/arch/arm/cpu/armv7/exynos/spl_boot.c
@@ -10,8 +10,11 @@
#include <asm/arch/clock.h>
#include <asm/arch/clk.h>
#include <asm/arch/dmc.h>
+#include <asm/arch/periph.h>
+#include <asm/arch/pinmux.h>
#include <asm/arch/power.h>
#include <asm/arch/spl.h>
+#include <asm/arch/spi.h>
#include "common_setup.h"
#include "clock_init.h"
@@ -59,6 +62,121 @@
}
#endif
+#ifdef CONFIG_SPI_BOOTING
+static void spi_rx_tx(struct exynos_spi *regs, int todo,
+ void *dinp, void const *doutp, int i)
+{
+ uint *rxp = (uint *)(dinp + (i * (32 * 1024)));
+ int rx_lvl, tx_lvl;
+ uint out_bytes, in_bytes;
+
+ out_bytes = todo;
+ in_bytes = todo;
+ setbits_le32(®s->ch_cfg, SPI_CH_RST);
+ clrbits_le32(®s->ch_cfg, SPI_CH_RST);
+ writel(((todo * 8) / 32) | SPI_PACKET_CNT_EN, ®s->pkt_cnt);
+
+ while (in_bytes) {
+ uint32_t spi_sts;
+ int temp;
+
+ spi_sts = readl(®s->spi_sts);
+ rx_lvl = ((spi_sts >> 15) & 0x7f);
+ tx_lvl = ((spi_sts >> 6) & 0x7f);
+ while (tx_lvl < 32 && out_bytes) {
+ temp = 0xffffffff;
+ writel(temp, ®s->tx_data);
+ out_bytes -= 4;
+ tx_lvl += 4;
+ }
+ while (rx_lvl >= 4 && in_bytes) {
+ temp = readl(®s->rx_data);
+ if (rxp)
+ *rxp++ = temp;
+ in_bytes -= 4;
+ rx_lvl -= 4;
+ }
+ }
+}
+
+/*
+ * Copy uboot from spi flash to RAM
+ *
+ * @parma uboot_size size of u-boot to copy
+ * @param uboot_addr address in u-boot to copy
+ */
+static void exynos_spi_copy(unsigned int uboot_size, unsigned int uboot_addr)
+{
+ int upto, todo;
+ int i, timeout = 100;
+ struct exynos_spi *regs = (struct exynos_spi *)CONFIG_ENV_SPI_BASE;
+
+ set_spi_clk(PERIPH_ID_SPI1, 50000000); /* set spi clock to 50Mhz */
+ /* set the spi1 GPIO */
+ exynos_pinmux_config(PERIPH_ID_SPI1, PINMUX_FLAG_NONE);
+
+ /* set pktcnt and enable it */
+ writel(4 | SPI_PACKET_CNT_EN, ®s->pkt_cnt);
+ /* set FB_CLK_SEL */
+ writel(SPI_FB_DELAY_180, ®s->fb_clk);
+ /* set CH_WIDTH and BUS_WIDTH as word */
+ setbits_le32(®s->mode_cfg, SPI_MODE_CH_WIDTH_WORD |
+ SPI_MODE_BUS_WIDTH_WORD);
+ clrbits_le32(®s->ch_cfg, SPI_CH_CPOL_L); /* CPOL: active high */
+
+ /* clear rx and tx channel if set priveously */
+ clrbits_le32(®s->ch_cfg, SPI_RX_CH_ON | SPI_TX_CH_ON);
+
+ setbits_le32(®s->swap_cfg, SPI_RX_SWAP_EN |
+ SPI_RX_BYTE_SWAP |
+ SPI_RX_HWORD_SWAP);
+
+ /* do a soft reset */
+ setbits_le32(®s->ch_cfg, SPI_CH_RST);
+ clrbits_le32(®s->ch_cfg, SPI_CH_RST);
+
+ /* now set rx and tx channel ON */
+ setbits_le32(®s->ch_cfg, SPI_RX_CH_ON | SPI_TX_CH_ON | SPI_CH_HS_EN);
+ clrbits_le32(®s->cs_reg, SPI_SLAVE_SIG_INACT); /* CS low */
+
+ /* Send read instruction (0x3h) followed by a 24 bit addr */
+ writel((SF_READ_DATA_CMD << 24) | SPI_FLASH_UBOOT_POS, ®s->tx_data);
+
+ /* waiting for TX done */
+ while (!(readl(®s->spi_sts) & SPI_ST_TX_DONE)) {
+ if (!timeout) {
+ debug("SPI TIMEOUT\n");
+ break;
+ }
+ timeout--;
+ }
+
+ for (upto = 0, i = 0; upto < uboot_size; upto += todo, i++) {
+ todo = min(uboot_size - upto, (1 << 15));
+ spi_rx_tx(regs, todo, (void *)(uboot_addr),
+ (void *)(SPI_FLASH_UBOOT_POS), i);
+ }
+
+ setbits_le32(®s->cs_reg, SPI_SLAVE_SIG_INACT);/* make the CS high */
+
+ /*
+ * Let put controller mode to BYTE as
+ * SPI driver does not support WORD mode yet
+ */
+ clrbits_le32(®s->mode_cfg, SPI_MODE_CH_WIDTH_WORD |
+ SPI_MODE_BUS_WIDTH_WORD);
+ writel(0, ®s->swap_cfg);
+
+ /*
+ * Flush spi tx, rx fifos and reset the SPI controller
+ * and clear rx/tx channel
+ */
+ clrsetbits_le32(®s->ch_cfg, SPI_CH_HS_EN, SPI_CH_RST);
+ clrbits_le32(®s->ch_cfg, SPI_CH_RST);
+ clrbits_le32(®s->ch_cfg, SPI_TX_CH_ON | SPI_RX_CH_ON);
+}
+#endif
+
/*
* Copy U-boot from mmc to RAM:
* COPY_BL2_FNPTR_ADDR: Address in iRAM, which Contains
@@ -70,6 +188,9 @@
u32 (*copy_bl2)(u32 offset, u32 nblock, u32 dst) = NULL;
u32 offset = 0, size = 0;
+#ifdef CONFIG_SPI_BOOTING
+ struct spl_machine_param *param = spl_get_machine_params();
+#endif
#ifdef CONFIG_SUPPORT_EMMC_BOOT
u32 (*copy_bl2_from_emmc)(u32 nblock, u32 dst);
void (*end_bootop_from_emmc)(void);
@@ -91,9 +212,8 @@
switch (bootmode) {
#ifdef CONFIG_SPI_BOOTING
case BOOT_MODE_SERIAL:
- offset = SPI_FLASH_UBOOT_POS;
- size = CONFIG_BL2_SIZE;
- copy_bl2 = get_irom_func(SPI_INDEX);
+ /* Customised function to copy u-boot from SF */
+ exynos_spi_copy(param->uboot_size, CONFIG_SYS_TEXT_BASE);
break;
#endif
case BOOT_MODE_MMC:
diff --git a/arch/arm/include/asm/arch-exynos/dwmmc.h b/arch/arm/include/asm/arch-exynos/dwmmc.h
index d1c5d4f..09d739d 100644
--- a/arch/arm/include/asm/arch-exynos/dwmmc.h
+++ b/arch/arm/include/asm/arch-exynos/dwmmc.h
@@ -6,10 +6,6 @@
*/
#define DWMCI_CLKSEL 0x09C
-#define DWMCI_SHIFT_0 0x0
-#define DWMCI_SHIFT_1 0x1
-#define DWMCI_SHIFT_2 0x2
-#define DWMCI_SHIFT_3 0x3
#define DWMCI_SET_SAMPLE_CLK(x) (x)
#define DWMCI_SET_DRV_CLK(x) ((x) << 16)
#define DWMCI_SET_DIV_RATIO(x) ((x) << 24)
diff --git a/arch/arm/include/asm/arch-exynos/mmc.h b/arch/arm/include/asm/arch-exynos/mmc.h
index 98312d1..98d6530 100644
--- a/arch/arm/include/asm/arch-exynos/mmc.h
+++ b/arch/arm/include/asm/arch-exynos/mmc.h
@@ -55,7 +55,7 @@
int s5p_sdhci_init(u32 regbase, int index, int bus_width);
-static inline unsigned int s5p_mmc_init(int index, int bus_width)
+static inline int s5p_mmc_init(int index, int bus_width)
{
unsigned int base = samsung_get_base_mmc() +
(S5P_MMC_DEV_OFFSET * index);
diff --git a/arch/arm/include/asm/arch-exynos/power.h b/arch/arm/include/asm/arch-exynos/power.h
index 8db18c5..2bfee18 100644
--- a/arch/arm/include/asm/arch-exynos/power.h
+++ b/arch/arm/include/asm/arch-exynos/power.h
@@ -16,7 +16,7 @@
unsigned int gnss_rtc_out_ctrl;
unsigned char res2[0x1ec];
unsigned int system_power_down_ctrl;
- unsigned char res3[0x1];
+ unsigned int res3;
unsigned int system_power_down_option;
unsigned char res4[0x1f4];
unsigned int swreset;
diff --git a/arch/arm/include/asm/arch-exynos/spi.h b/arch/arm/include/asm/arch-exynos/spi.h
index 147c1a7..0ba931b 100644
--- a/arch/arm/include/asm/arch-exynos/spi.h
+++ b/arch/arm/include/asm/arch-exynos/spi.h
@@ -30,6 +30,7 @@
#define EXYNOS_SPI_MAX_FREQ 50000000
#define SPI_TIMEOUT_MS 10
+#define SF_READ_DATA_CMD 0x3
/* SPI_CHCFG */
#define SPI_CH_HS_EN (1 << 6)
diff --git a/arch/arm/include/asm/arch-s5pc1xx/mmc.h b/arch/arm/include/asm/arch-s5pc1xx/mmc.h
index 55ff10b..dd473c8 100644
--- a/arch/arm/include/asm/arch-s5pc1xx/mmc.h
+++ b/arch/arm/include/asm/arch-s5pc1xx/mmc.h
@@ -55,7 +55,7 @@
int s5p_sdhci_init(u32 regbase, int index, int bus_width);
-static inline unsigned int s5p_mmc_init(int index, int bus_width)
+static inline int s5p_mmc_init(int index, int bus_width)
{
unsigned int base = samsung_get_base_mmc() +
(S5P_MMC_DEV_OFFSET * index);
diff --git a/board/samsung/trats/trats.c b/board/samsung/trats/trats.c
index 7012c13..6bd106e 100644
--- a/board/samsung/trats/trats.c
+++ b/board/samsung/trats/trats.c
@@ -501,6 +501,17 @@
debug("USB_udc_probe\n");
return s3c_udc_probe(&s5pc210_otg_data);
}
+
+#ifdef CONFIG_USB_CABLE_CHECK
+int usb_cable_connected(void)
+{
+ struct pmic *muic = pmic_get("MAX8997_MUIC");
+ if (!muic)
+ return 0;
+
+ return !!muic->chrg->chrg_type(muic);
+}
+#endif
#endif
static void pmic_reset(void)
diff --git a/board/samsung/trats2/trats2.c b/board/samsung/trats2/trats2.c
index d44d825..9552522 100644
--- a/board/samsung/trats2/trats2.c
+++ b/board/samsung/trats2/trats2.c
@@ -25,6 +25,9 @@
#include <power/max77693_fg.h>
#include <libtizen.h>
#include <errno.h>
+#include <usb.h>
+#include <usb/s3c_udc.h>
+#include <usb_mass_storage.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -40,7 +43,7 @@
int modelrev = 0;
int i;
- gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE;
+ gpio2 = (struct exynos4x12_gpio_part2 *)samsung_get_base_gpio_part2();
/*
* GPM1[1:0]: MODEL_REV[1:0]
@@ -90,7 +93,7 @@
static void board_external_gpio_init(void)
{
- gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE;
+ gpio2 = (struct exynos4x12_gpio_part2 *)samsung_get_base_gpio_part2();
/*
* some pins which in alive block are connected with external pull-up
@@ -115,8 +118,8 @@
#ifdef CONFIG_SYS_I2C_INIT_BOARD
static void board_init_i2c(void)
{
- gpio1 = (struct exynos4x12_gpio_part1 *)EXYNOS4X12_GPIO_PART1_BASE;
- gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE;
+ gpio1 = (struct exynos4x12_gpio_part1 *)samsung_get_base_gpio_part1();
+ gpio2 = (struct exynos4x12_gpio_part2 *)samsung_get_base_gpio_part2();
/* I2C_7 */
s5p_gpio_direction_output(&gpio1->d0, 2, 1);
@@ -147,7 +150,7 @@
int board_init(void)
{
struct exynos4_power *pwr =
- (struct exynos4_power *)EXYNOS4X12_POWER_BASE;
+ (struct exynos4_power *)samsung_get_base_power();
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
@@ -254,7 +257,7 @@
{
int err0, err2 = 0;
- gpio2 = (struct exynos4x12_gpio_part2 *)EXYNOS4X12_GPIO_PART2_BASE;
+ gpio2 = (struct exynos4x12_gpio_part2 *)samsung_get_base_gpio_part2();
/* eMMC_EN: SD_0_CDn: GPK0[2] Output High */
s5p_gpio_direction_output(&gpio2->k0, 2, 1);
@@ -308,6 +311,95 @@
return err0 & err2;
}
+#ifdef CONFIG_USB_GADGET
+static int s5pc210_phy_control(int on)
+{
+ int ret = 0;
+ unsigned int val;
+ struct pmic *p, *p_pmic, *p_muic;
+
+ p_pmic = pmic_get("MAX77686_PMIC");
+ if (!p_pmic)
+ return -ENODEV;
+
+ if (pmic_probe(p_pmic))
+ return -1;
+
+ p_muic = pmic_get("MAX77693_MUIC");
+ if (!p_muic)
+ return -ENODEV;
+
+ if (pmic_probe(p_muic))
+ return -1;
+
+ if (on) {
+ ret = max77686_set_ldo_mode(p_pmic, 12, OPMODE_ON);
+ if (ret)
+ return -1;
+
+ p = pmic_get("MAX77693_PMIC");
+ if (!p)
+ return -ENODEV;
+
+ if (pmic_probe(p))
+ return -1;
+
+ /* SAFEOUT */
+ ret = pmic_reg_read(p, MAX77693_SAFEOUT, &val);
+ if (ret)
+ return -1;
+
+ val |= MAX77693_ENSAFEOUT1;
+ ret = pmic_reg_write(p, MAX77693_SAFEOUT, val);
+ if (ret)
+ return -1;
+
+ /* PATH: USB */
+ ret = pmic_reg_write(p_muic, MAX77693_MUIC_CONTROL1,
+ MAX77693_MUIC_CTRL1_DN1DP2);
+
+ } else {
+ ret = max77686_set_ldo_mode(p_pmic, 12, OPMODE_LPM);
+ if (ret)
+ return -1;
+
+ /* PATH: UART */
+ ret = pmic_reg_write(p_muic, MAX77693_MUIC_CONTROL1,
+ MAX77693_MUIC_CTRL1_UT1UR2);
+ }
+
+ if (ret)
+ return -1;
+
+ return 0;
+}
+
+struct s3c_plat_otg_data s5pc210_otg_data = {
+ .phy_control = s5pc210_phy_control,
+ .regs_phy = EXYNOS4X12_USBPHY_BASE,
+ .regs_otg = EXYNOS4X12_USBOTG_BASE,
+ .usb_phy_ctrl = EXYNOS4X12_USBPHY_CONTROL,
+ .usb_flags = PHY0_SLEEP,
+};
+
+int board_usb_init(int index, enum usb_init_type init)
+{
+ debug("USB_udc_probe\n");
+ return s3c_udc_probe(&s5pc210_otg_data);
+}
+
+#ifdef CONFIG_USB_CABLE_CHECK
+int usb_cable_connected(void)
+{
+ struct pmic *muic = pmic_get("MAX77693_MUIC");
+ if (!muic)
+ return 0;
+
+ return !!muic->chrg->chrg_type(muic);
+}
+#endif
+#endif
+
static int pmic_init_max77686(void)
{
struct pmic *p = pmic_get("MAX77686_PMIC");
@@ -421,7 +513,7 @@
{
struct pmic *p = pmic_get("MAX77686_PMIC");
- gpio1 = (struct exynos4x12_gpio_part1 *)EXYNOS4X12_GPIO_PART1_BASE;
+ gpio1 = (struct exynos4x12_gpio_part1 *)samsung_get_base_gpio_part1();
/* LCD_2.2V_EN: GPC0[1] */
s5p_gpio_set_pull(&gpio1->c0, 1, GPIO_PULL_UP);
@@ -435,7 +527,7 @@
void exynos_reset_lcd(void)
{
- gpio1 = (struct exynos4x12_gpio_part1 *)EXYNOS4X12_GPIO_PART1_BASE;
+ gpio1 = (struct exynos4x12_gpio_part1 *)samsung_get_base_gpio_part1();
/* reset lcd */
s5p_gpio_direction_output(&gpio1->f2, 1, 0);
diff --git a/drivers/usb/gadget/regs-otg.h b/drivers/usb/gadget/regs-otg.h
index 84bfcc5..ac5d112 100644
--- a/drivers/usb/gadget/regs-otg.h
+++ b/drivers/usb/gadget/regs-otg.h
@@ -226,6 +226,11 @@
#define CLK_SEL_12MHZ (0x2 << 0)
#define CLK_SEL_48MHZ (0x0 << 0)
+#define EXYNOS4X12_ID_PULLUP0 (0x01 << 3)
+#define EXYNOS4X12_COMMON_ON_N0 (0x01 << 4)
+#define EXYNOS4X12_CLK_SEL_12MHZ (0x02 << 0)
+#define EXYNOS4X12_CLK_SEL_24MHZ (0x05 << 0)
+
/* Device Configuration Register DCFG */
#define DEV_SPEED_HIGH_SPEED_20 (0x0 << 0)
#define DEV_SPEED_FULL_SPEED_20 (0x1 << 0)
diff --git a/drivers/usb/gadget/s3c_udc_otg.c b/drivers/usb/gadget/s3c_udc_otg.c
index 7e20209..ba17a04 100644
--- a/drivers/usb/gadget/s3c_udc_otg.c
+++ b/drivers/usb/gadget/s3c_udc_otg.c
@@ -167,8 +167,13 @@
writel((readl(&phy->phypwr) &~(OTG_DISABLE_0 | ANALOG_PWRDOWN)
&~FORCE_SUSPEND_0), &phy->phypwr);
- writel((readl(&phy->phyclk) &~(ID_PULLUP0 | COMMON_ON_N0)) |
- CLK_SEL_24MHZ, &phy->phyclk); /* PLL 24Mhz */
+ if (s5p_cpu_id == 0x4412)
+ writel((readl(&phy->phyclk) & ~(EXYNOS4X12_ID_PULLUP0 |
+ EXYNOS4X12_COMMON_ON_N0)) | EXYNOS4X12_CLK_SEL_24MHZ,
+ &phy->phyclk); /* PLL 24Mhz */
+ else
+ writel((readl(&phy->phyclk) & ~(ID_PULLUP0 | COMMON_ON_N0)) |
+ CLK_SEL_24MHZ, &phy->phyclk); /* PLL 24Mhz */
writel((readl(&phy->rstcon) &~(LINK_SW_RST | PHYLNK_SW_RST))
| PHY_SW_RST0, &phy->rstcon);
diff --git a/include/configs/arndale.h b/include/configs/arndale.h
index 45fa047..f0b9f94 100644
--- a/include/configs/arndale.h
+++ b/include/configs/arndale.h
@@ -198,10 +198,6 @@
#define BL2_START_OFFSET (CONFIG_BL2_OFFSET/512)
#define BL2_SIZE_BLOC_COUNT (CONFIG_BL2_SIZE/512)
-#define CONFIG_SPI_BOOTING
-#define EXYNOS_COPY_SPI_FNPTR_ADDR 0x02020058
-#define SPI_FLASH_UBOOT_POS (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE)
-
#define CONFIG_DOS_PARTITION
#define CONFIG_EFI_PARTITION
#define CONFIG_CMD_PART
diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h
index bdefee1..dee18a7 100644
--- a/include/configs/exynos5250-dt.h
+++ b/include/configs/exynos5250-dt.h
@@ -157,6 +157,7 @@
#define COPY_BL2_FNPTR_ADDR 0x02020030
#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
/* specific .lds file */
#define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds"
@@ -255,7 +256,7 @@
#define CONFIG_DRIVER_S3C24X0_I2C
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_MAX_I2C_NUM 8
-#define CONFIG_SYS_I2C_SLAVE 0x0
+#define CONFIG_SYS_I2C_SLAVE 0x0
#define CONFIG_I2C_EDID
/* PMIC */
@@ -266,6 +267,7 @@
/* SPI */
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_SPI_FLASH
+#define CONFIG_ENV_SPI_BASE 0x12D30000
#ifdef CONFIG_SPI_FLASH
#define CONFIG_EXYNOS_SPI
@@ -290,27 +292,6 @@
#define CONFIG_POWER_I2C
#define CONFIG_POWER_MAX77686
-/* SPI */
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_SPI_FLASH
-
-#ifdef CONFIG_SPI_FLASH
-#define CONFIG_EXYNOS_SPI
-#define CONFIG_CMD_SF
-#define CONFIG_CMD_SPI
-#define CONFIG_SPI_FLASH_WINBOND
-#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
-#define CONFIG_SF_DEFAULT_SPEED 50000000
-#define EXYNOS5_SPI_NUM_CONTROLLERS 5
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_MODE SPI_MODE_0
-#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-#define CONFIG_ENV_SPI_BUS 1
-#define CONFIG_ENV_SPI_MAX_HZ 50000000
-#endif
-
/* Ethernet Controllor Driver */
#ifdef CONFIG_CMD_NET
#define CONFIG_SMC911X
diff --git a/include/configs/trats.h b/include/configs/trats.h
index 3d080c4..8ff9800 100644
--- a/include/configs/trats.h
+++ b/include/configs/trats.h
@@ -308,6 +308,7 @@
#define CONFIG_USB_GADGET_S3C_UDC_OTG
#define CONFIG_USB_GADGET_DUALSPEED
#define CONFIG_USB_GADGET_VBUS_DRAW 2
+#define CONFIG_USB_CABLE_CHECK
/* LCD */
#define CONFIG_EXYNOS_FB
diff --git a/include/configs/trats2.h b/include/configs/trats2.h
index 0e93836..c49a969e 100644
--- a/include/configs/trats2.h
+++ b/include/configs/trats2.h
@@ -20,8 +20,6 @@
#define CONFIG_EXYNOS4 /* which is in a EXYNOS4XXX */
#define CONFIG_TIZEN /* TIZEN lib */
-#define PLATFORM_NO_UNALIGNED
-
#include <asm/arch/cpu.h> /* get chip and board defs */
#define CONFIG_ARCH_CPU_INIT
@@ -65,10 +63,9 @@
#define CONFIG_DISPLAY_CPUINFO
-/*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (2 << 20))
+#include <asm/sizes.h>
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (80 * SZ_1M))
/* select serial console configuration */
#define CONFIG_SERIAL2
@@ -100,6 +97,7 @@
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MMC
+#define CONFIG_CMD_DFU
#define CONFIG_CMD_GPT
#define CONFIG_CMD_PMIC
@@ -113,6 +111,23 @@
#define CONFIG_CMD_EXT4
#define CONFIG_CMD_EXT4_WRITE
+/* USB Composite download gadget - g_dnl */
+#define CONFIG_USBDOWNLOAD_GADGET
+#define CONFIG_SYS_DFU_DATA_BUF_SIZE SZ_32M
+#define CONFIG_DFU_FUNCTION
+#define CONFIG_DFU_MMC
+
+/* TIZEN THOR downloader support */
+#define CONFIG_CMD_THOR_DOWNLOAD
+#define CONFIG_THOR_FUNCTION
+
+/* USB Samsung's IDs */
+#define CONFIG_G_DNL_VENDOR_NUM 0x04E8
+#define CONFIG_G_DNL_PRODUCT_NUM 0x6601
+#define CONFIG_G_DNL_THOR_VENDOR_NUM CONFIG_G_DNL_VENDOR_NUM
+#define CONFIG_G_DNL_THOR_PRODUCT_NUM 0x685D
+#define CONFIG_G_DNL_MANUFACTURER "Samsung"
+
/* To use the TFTPBOOT over USB, Please enable the CONFIG_CMD_NET */
#undef CONFIG_CMD_NET
@@ -136,25 +151,29 @@
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
/* Tizen - partitions definitions */
-#define PARTS_CSA "csa-mmc"
-#define PARTS_BOOTLOADER "u-boot"
+#define PARTS_CSA "csa"
#define PARTS_BOOT "boot"
+#define PARTS_MODEM "modem"
+#define PARTS_CSC "csc"
#define PARTS_ROOT "platform"
#define PARTS_DATA "data"
-#define PARTS_CSC "csc"
#define PARTS_UMS "ums"
#define PARTS_DEFAULT \
- "uuid_disk=${uuid_gpt_disk};" \
- "name="PARTS_CSA",size=8MiB,uuid=${uuid_gpt_"PARTS_CSA"};" \
- "name="PARTS_BOOTLOADER",size=60MiB," \
- "uuid=${uuid_gpt_"PARTS_BOOTLOADER"};" \
- "name="PARTS_BOOT",size=100MiB,uuid=${uuid_gpt_"PARTS_BOOT"};" \
- "name="PARTS_ROOT",size=1GiB,uuid=${uuid_gpt_"PARTS_ROOT"};" \
- "name="PARTS_DATA",size=3GiB,uuid=${uuid_gpt_"PARTS_DATA"};" \
+ "name="PARTS_CSA",start=5MiB,size=8MiB,uuid=${uuid_gpt_"PARTS_CSA"};" \
+ "name="PARTS_BOOT",size=64MiB,uuid=${uuid_gpt_"PARTS_BOOT"};" \
+ "name="PARTS_MODEM",size=100MiB,uuid=${uuid_gpt_"PARTS_MODEM"};" \
"name="PARTS_CSC",size=150MiB,uuid=${uuid_gpt_"PARTS_CSC"};" \
+ "name="PARTS_ROOT",size=1536MiB,uuid=${uuid_gpt_"PARTS_ROOT"};" \
+ "name="PARTS_DATA",size=512MiB,uuid=${uuid_gpt_"PARTS_DATA"};" \
"name="PARTS_UMS",size=-,uuid=${uuid_gpt_"PARTS_UMS"}\0" \
+#define CONFIG_DFU_ALT \
+ "u-boot mmc 80 800;" \
+ "uImage ext4 0 2;" \
+ "exynos4412-trats2.dtb ext4 0 2;" \
+ ""PARTS_ROOT" part 0 5\0"
+
#define CONFIG_EXTRA_ENV_SETTINGS \
"bootk=" \
"run loaddtb; run loaduimage; bootm 0x40007FC0 - ${fdtaddr}\0" \
@@ -178,15 +197,16 @@
"rootfstype=ext4\0" \
"console=" CONFIG_DEFAULT_CONSOLE \
"kernelname=uImage\0" \
- "loaduimage=ext4load mmc ${mmcdev}:${mmcbootpart} 0x40007FC0 uImage\0" \
- "0x40007FC0 ${kernelname}\0" \
+ "loaduimage=ext4load mmc ${mmcdev}:${mmcbootpart} 0x40007FC0 " \
+ "${kernelname}\0" \
"loaddtb=ext4load mmc ${mmcdev}:${mmcbootpart} ${fdtaddr} " \
"${fdtfile}\0" \
- "mmcdev=0\0" \
+ "mmcdev=CONFIG_MMC_DEFAULT_DEV\0" \
"mmcbootpart=2\0" \
"mmcrootpart=5\0" \
"opts=always_resume=1\0" \
"partitions=" PARTS_DEFAULT \
+ "dfu_alt_info=" CONFIG_DFU_ALT \
"uartpath=ap\0" \
"usbpath=ap\0" \
"consoleon=set console console=ttySAC2,115200n8; save; reset\0" \
@@ -233,8 +253,6 @@
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR \
- GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_HZ 1000
-
/* valid baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
@@ -293,6 +311,11 @@
#define CONFIG_POWER_MUIC_MAX77693
#define CONFIG_POWER_FG_MAX77693
#define CONFIG_POWER_BATTERY_TRATS2
+#define CONFIG_USB_GADGET
+#define CONFIG_USB_GADGET_S3C_UDC_OTG
+#define CONFIG_USB_GADGET_DUALSPEED
+#define CONFIG_USB_GADGET_VBUS_DRAW 2
+#define CONFIG_USB_CABLE_CHECK
/* LCD */
#define CONFIG_EXYNOS_FB
@@ -305,6 +328,9 @@
#define CONFIG_VIDEO_BMP_GZIP
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE ((500 * 250 * 4) + (1 << 12))
+#define CONFIG_CMD_USB_MASS_STORAGE
+#define CONFIG_USB_GADGET_MASS_STORAGE
+
/* Pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1