commit 8d6fe61315e508c1574149d658b5d2cb11630c45
author Samuel Holland <samuel@sholland.org> Wed Apr 27 15:31:24 2022 -0500
committer Andre Przywara <andre.przywara@arm.com> Mon May 23 00:37:51 2022 +0100
tree bdb998beedff01ae021c79ca89e626e46ba9fe3e
parent 5e075958d499039158da828eb28b815ea0baf678

ARM: dts: sunxi: A13/A31/A23/A33: Sync from Linux v5.18-rc1

Copy the devicetree source for the A10s/A13/GR8, A31(s), and A23/A33/R16
SoCs and all existing boards from the Linux v5.18-rc1 tag.

These changes are combined into one commit due to interdependencies:
 - The unit addresses were removed from bitbanged I2C buses, which
   drives a Kconfig default change. This affects sun5i-a13-utoo-p66.dts
   and sun6i-a31-colombus.dts.
 - The pinctrl nodes were renamed, including some used by the shared
   header sunxi-reference-design-tablet.dtsi.

To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.

This commit renames the file sun8i-r16-nintendo-nes-classic-edition.dts
to sun8i-r16-nintendo-nes-classic.dts to match the Linux tree.

This commit also adds the following new board devicetrees:
 - sun5i-a13-licheepi-one.dts
 - sun5i-a13-pocketbook-touch-lux-3.dts
 - sun5i-gr8-evb.dts
 - sun8i-a23-ippo-q8h-v1.2.dts
 - sun8i-a23-ippo-q8h-v5.dts
 - sun8i-a33-et-q8-v1.6.dts
 - sun8i-a33-ippo-q8h-v1.2.dts
 - sun8i-r16-nintendo-super-nes-classic.dts

As with the other SoCs, updates of note are conversion of GPIO pull-up
from pinconf to GPIO flags and renaming the detection GPIO properties in
the USB PHY nodes.

Signed-off-by: Samuel Holland <samuel@sholland.org>

arch/arm/dts/sun8i-a33-sinlinx-sina33.dts

diff --git a/arch/arm/dts/sun8i-a33-sinlinx-sina33.dts b/arch/arm/dts/sun8i-a33-sinlinx-sina33.dts
index 541acb4..d54a067 100644
--- a/arch/arm/dts/sun8i-a33-sinlinx-sina33.dts
+++ b/arch/arm/dts/sun8i-a33-sinlinx-sina33.dts
@@ -63,16 +63,10 @@
 
 	panel {
 		compatible = "netron-dy,e231732";
-		#address-cells = <1>;
-		#size-cells = <0>;
+		power-supply = <&reg_vcc3v3>;
 
-		port@0 {
-			reg = <0>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			panel_input: endpoint@0 {
-				reg = <0>;
+		port {
+			panel_input: endpoint {
 				remote-endpoint = <&tcon0_out_panel>;
 			};
 		};
@@ -117,21 +111,21 @@
 	vref-supply = <&reg_dcdc1>;
 	status = "okay";
 
-	button@200 {
+	button-200 {
 		label = "Volume Up";
 		linux,code = <KEY_VOLUMEUP>;
 		channel = <0>;
 		voltage = <191011>;
 	};
 
-	button@400 {
+	button-400 {
 		label = "Volume Down";
 		linux,code = <KEY_VOLUMEDOWN>;
 		channel = <0>;
 		voltage = <391304>;
 	};
 
-	button@600 {
+	button-600 {
 		label = "Home";
 		linux,code = <KEY_HOME>;
 		channel = <0>;
@@ -140,8 +134,6 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_sina33>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 1 4 GPIO_ACTIVE_LOW>; /* PB4 */
@@ -161,29 +153,19 @@
 &mmc2_8bit_pins {
 	/* Increase drive strength for DDR modes */
 	drive-strength = <40>;
-	/* eMMC is missing pull-ups */
-	bias-pull-up;
 };
 
 &ohci0 {
 	status = "okay";
 };
 
-&pio {
-	mmc0_cd_pin_sina33: mmc0_cd_pin@0 {
-		pins = "PB4";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-};
-
 &r_rsb {
 	status = "okay";
 
 	axp22x: pmic@3a3 {
 		compatible = "x-powers,axp223";
 		reg = <0x3a3>;
-		interrupt-parent = <&nmi_intc>;
+		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 		eldoin-supply = <&reg_dcdc1>;
 	};
@@ -278,7 +260,7 @@
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_b>;
+	pinctrl-0 = <&uart0_pb_pins>;
 	status = "okay";
 };