ARM: dts: sunxi: A13/A31/A23/A33: Sync from Linux v5.18-rc1
Copy the devicetree source for the A10s/A13/GR8, A31(s), and A23/A33/R16
SoCs and all existing boards from the Linux v5.18-rc1 tag.
These changes are combined into one commit due to interdependencies:
- The unit addresses were removed from bitbanged I2C buses, which
drives a Kconfig default change. This affects sun5i-a13-utoo-p66.dts
and sun6i-a31-colombus.dts.
- The pinctrl nodes were renamed, including some used by the shared
header sunxi-reference-design-tablet.dtsi.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
This commit renames the file sun8i-r16-nintendo-nes-classic-edition.dts
to sun8i-r16-nintendo-nes-classic.dts to match the Linux tree.
This commit also adds the following new board devicetrees:
- sun5i-a13-licheepi-one.dts
- sun5i-a13-pocketbook-touch-lux-3.dts
- sun5i-gr8-evb.dts
- sun8i-a23-ippo-q8h-v1.2.dts
- sun8i-a23-ippo-q8h-v5.dts
- sun8i-a33-et-q8-v1.6.dts
- sun8i-a33-ippo-q8h-v1.2.dts
- sun8i-r16-nintendo-super-nes-classic.dts
As with the other SoCs, updates of note are conversion of GPIO pull-up
from pinconf to GPIO flags and renaming the detection GPIO properties in
the USB PHY nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
diff --git a/arch/arm/dts/sun8i-a33-inet-d978-rev2.dts b/arch/arm/dts/sun8i-a33-inet-d978-rev2.dts
index 3e05959..065cb62 100644
--- a/arch/arm/dts/sun8i-a33-inet-d978-rev2.dts
+++ b/arch/arm/dts/sun8i-a33-inet-d978-rev2.dts
@@ -63,20 +63,16 @@
pinctrl-names = "default";
pinctrl-0 = <&led_pin_d978>;
- home {
+ led {
label = "d978:blue:home";
gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */
};
};
};
-&mmc1_pins_a {
- bias-pull-up;
-};
-
&mmc1 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins_a>;
+ pinctrl-0 = <&mmc1_pg_pins>;
vmmc-supply = <®_dldo1>;
bus-width = <4>;
non-removable;
@@ -88,7 +84,7 @@
};
&r_pio {
- led_pin_d978: led_pin_d978@0 {
+ led_pin_d978: led-pin {
pins = "PL5";
function = "gpio_out";
drive-strength = <20>;
@@ -101,7 +97,7 @@
&uart1 {
pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins_a>,
- <&uart1_pins_cts_rts_a>;
+ pinctrl-0 = <&uart1_pg_pins>,
+ <&uart1_cts_rts_pg_pins>;
status = "okay";
};