powerpc/85xx: Add P1021 specific QE and UEC support
P1021 has some QE pins which need to be set in pmuxcr register before
using QE functions. In this patch, pin QE0 and QE3 are set for UCC1 and
UCC5 in Eth mode. QE9 and QE12 are set for MII management. QE12 needs to
be released after MII access because QE12 pin is muxed with LBCTL signal.
Also added relevant QE support defines unique to P1021.
The P1021 QE is shared on P1012, P1016, and P1025.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
diff --git a/drivers/qe/uec.c b/drivers/qe/uec.c
index 282ab23..811e3fc 100644
--- a/drivers/qe/uec.c
+++ b/drivers/qe/uec.c
@@ -1,5 +1,5 @@
/*
- * Copyright (C) 2006-2010 Freescale Semiconductor, Inc.
+ * Copyright (C) 2006-2011 Freescale Semiconductor, Inc.
*
* Dave Liu <daveliu@freescale.com>
*
@@ -588,9 +588,27 @@
{
uec_private_t *uec = (uec_private_t *)dev->priv;
+#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \
+ defined(CONFIG_P1021) || defined(CONFIG_P1025)
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+
+ /* QE9 and QE12 need to be set for enabling QE MII managment signals */
+ setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE9);
+ setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12);
+#endif
+
/* Update the link, speed, duplex */
uec->mii_info->phyinfo->read_status(uec->mii_info);
+#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \
+ defined(CONFIG_P1021) || defined(CONFIG_P1025)
+ /*
+ * QE12 is muxed with LBCTL, it needs to be released for enabling
+ * LBCTL signal for LBC usage.
+ */
+ clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12);
+#endif
+
/* Adjust the interface according to speed */
adjust_link(dev);
}
@@ -1198,10 +1216,21 @@
uec_private_t *uec;
int err, i;
struct phy_info *curphy;
+#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \
+ defined(CONFIG_P1021) || defined(CONFIG_P1025)
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+#endif
uec = (uec_private_t *)dev->priv;
if (uec->the_first_run == 0) {
+#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \
+ defined(CONFIG_P1021) || defined(CONFIG_P1025)
+ /* QE9 and QE12 need to be set for enabling QE MII managment signals */
+ setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE9);
+ setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12);
+#endif
+
err = init_phy(dev);
if (err) {
printf("%s: Cannot initialize PHY, aborting.\n",
@@ -1228,6 +1257,12 @@
udelay(100000);
} while (1);
+#if defined(CONFIG_P1012) || defined(CONFIG_P1016) || \
+ defined(CONFIG_P1021) || defined(CONFIG_P1025)
+ /* QE12 needs to be released for enabling LBCTL signal*/
+ clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12);
+#endif
+
if (err || i <= 0)
printf("warning: %s: timeout on PHY link\n", dev->name);