board: endeavoru: convert HTC One X to use DM PMIC
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
diff --git a/board/htc/endeavoru/endeavoru-spl.c b/board/htc/endeavoru/endeavoru-spl.c
index 7921ff1..2525b50 100644
--- a/board/htc/endeavoru/endeavoru-spl.c
+++ b/board/htc/endeavoru/endeavoru-spl.c
@@ -9,7 +9,7 @@
* Svyatoslav Ryhel <clamor95@gmail.com>
*/
-#include <common.h>
+#include <asm/arch/tegra.h>
#include <asm/arch-tegra/tegra_i2c.h>
#include <linux/delay.h>
diff --git a/board/htc/endeavoru/endeavoru.c b/board/htc/endeavoru/endeavoru.c
index e1a0b24..7fb6125 100644
--- a/board/htc/endeavoru/endeavoru.c
+++ b/board/htc/endeavoru/endeavoru.c
@@ -7,48 +7,11 @@
* Svyatoslav Ryhel <clamor95@gmail.com>
*/
-#include <common.h>
#include <dm.h>
#include <fdt_support.h>
-#include <i2c.h>
-#include <log.h>
#include <asm/arch/pinmux.h>
-#include <asm/arch/gp_padctrl.h>
-#include <asm/arch/gpio.h>
-#include <asm/gpio.h>
-#include <linux/delay.h>
-#include "pinmux-config-endeavoru.h"
-
-#define TPS80032_CTL1_I2C_ADDR 0x48
-#define TPS80032_PHOENIX_DEV_ON 0x25
-#define DEVOFF BIT(0)
-#define TPS80032_LDO1_CFG_STATE 0x9E
-#define TPS80032_LDO1_CFG_VOLTAGE 0x9F
-
-#ifdef CONFIG_CMD_POWEROFF
-int do_poweroff(struct cmd_tbl *cmdtp, int flag,
- int argc, char *const argv[])
-{
- struct udevice *dev;
- int ret;
-
- ret = i2c_get_chip_for_busnum(0, TPS80032_CTL1_I2C_ADDR, 1, &dev);
- if (ret) {
- log_debug("cannot find PMIC I2C chip\n");
- return 0;
- }
- ret = dm_i2c_reg_write(dev, TPS80032_PHOENIX_DEV_ON, DEVOFF);
- if (ret)
- return ret;
-
- // wait some time and then print error
- mdelay(5000);
-
- printf("Failed to power off!!!\n");
- return 1;
-}
-#endif
+#include "pinmux-config-endeavoru.h"
/*
* Routine: pinmux_init
@@ -59,38 +22,6 @@
pinmux_config_pingrp_table(endeavoru_pinmux_common,
ARRAY_SIZE(endeavoru_pinmux_common));
}
-
-#ifdef CONFIG_MMC_SDHCI_TEGRA
-static void tps80032_voltage_init(void)
-{
- struct udevice *dev;
- int ret;
-
- ret = i2c_get_chip_for_busnum(0, TPS80032_CTL1_I2C_ADDR, 1, &dev);
- if (ret)
- log_debug("cannot find PMIC I2C chip\n");
-
- /* TPS80032: LDO1_REG = 1.2v to DSI */
- ret = dm_i2c_reg_write(dev, TPS80032_LDO1_CFG_VOLTAGE, 0x03);
- if (ret)
- log_debug("avdd_dsi_csi voltage set failed: %d\n", ret);
-
- /* TPS80032: LDO1_REG enable */
- ret = dm_i2c_reg_write(dev, TPS80032_LDO1_CFG_STATE, 0x01);
- if (ret)
- log_debug("avdd_dsi_csi enable failed: %d\n", ret);
-}
-
-/*
- * Routine: pin_mux_mmc
- * Description: setup the MMC muxes, power rails, etc.
- */
-void pin_mux_mmc(void)
-{
- /* Bring up DSI power */
- tps80032_voltage_init();
-}
-#endif /* MMC */
#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
int ft_board_setup(void *blob, struct bd_info *bd)