arm: ti: Remove omap4 platform support
There are no longer any OMAP4 platforms in U-Boot, remove the related
functionality.
Signed-off-by: Tom Rini <trini@konsulko.com>
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 8465b54..c07dd68 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -29,29 +29,6 @@
imply SYS_THUMB_BUILD
imply TWL4030_POWER
-config OMAP44XX
- bool "OMAP44XX SoC"
- select DM_EVENT
- select SPL_USE_TINY_PRINTF
- select SPL_SYS_NO_VECTOR_TABLE if SPL
- imply NAND_OMAP_ELM
- imply NAND_OMAP_GPMC
- imply SPL_DISPLAY_PRINT
- imply SPL_FS_EXT4
- imply SPL_FS_FAT
- imply SPL_GPIO
- imply SPL_I2C
- imply SPL_LIBCOMMON_SUPPORT
- imply SPL_LIBDISK_SUPPORT
- imply SPL_LIBGENERIC_SUPPORT
- imply SPL_MMC
- imply SPL_NAND_SIMPLE
- imply SPL_NAND_SUPPORT
- imply SPL_POWER
- imply SPL_SERIAL
- imply SYS_I2C_OMAP24XX
- imply SYS_THUMB_BUILD
-
config OMAP54XX
bool "OMAP54XX SoC"
select ARM_CORTEX_A15_CVE_2017_5715
@@ -162,7 +139,7 @@
bool
choice
- depends on OMAP44XX || OMAP54XX
+ depends on OMAP54XX
prompt "Static or dynamic DDR timing calculations"
default SYS_EMIF_PRECALCULATED_TIMING_REGS
help
@@ -181,8 +158,6 @@
source "arch/arm/mach-omap2/omap3/Kconfig"
-source "arch/arm/mach-omap2/omap4/Kconfig"
-
source "arch/arm/mach-omap2/omap5/Kconfig"
source "arch/arm/mach-omap2/am33xx/Kconfig"
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 8c10c69..d683c64 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -5,7 +5,6 @@
obj-$(if $(filter am33xx,$(SOC)),y) += am33xx/
obj-$(CONFIG_OMAP34XX) += omap3/
-obj-$(CONFIG_OMAP44XX) += omap4/
obj-$(CONFIG_OMAP54XX) += omap5/
obj-y += reset.o
@@ -19,7 +18,7 @@
obj-y += utils.o
obj-y += sysinfo-common.o
-ifneq ($(CONFIG_OMAP44XX)$(CONFIG_OMAP54XX),)
+ifdef CONFIG_OMAP54XX
obj-y += hwinit-common.o
obj-y += clocks-common.o
obj-y += emif-common.o
diff --git a/arch/arm/mach-omap2/emif-common.c b/arch/arm/mach-omap2/emif-common.c
index 4d431e2..a60eb99 100644
--- a/arch/arm/mach-omap2/emif-common.c
+++ b/arch/arm/mach-omap2/emif-common.c
@@ -202,7 +202,6 @@
}
}
-#ifndef CONFIG_OMAP44XX
static void omap5_ddr3_leveling(u32 base, const struct emif_regs *regs)
{
struct emif_reg_struct *emif = (struct emif_reg_struct *)base;
@@ -510,7 +509,6 @@
else
dra7_ddr3_init(base, regs);
}
-#endif
#ifndef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
#define print_timing_reg(reg) debug(#reg" - 0x%08x\n", (reg))
@@ -1292,10 +1290,8 @@
if (emif_sdram_type(regs->sdram_config) ==
EMIF_SDRAM_TYPE_LPDDR2)
lpddr2_init(base, regs);
-#ifndef CONFIG_OMAP44XX
else
ddr3_init(base, regs);
-#endif
}
#ifdef CONFIG_OMAP54XX
if (warm_reset() && (emif_sdram_type(regs->sdram_config) ==
diff --git a/arch/arm/mach-omap2/omap4/Kconfig b/arch/arm/mach-omap2/omap4/Kconfig
deleted file mode 100644
index 3f91c4c..0000000
--- a/arch/arm/mach-omap2/omap4/Kconfig
+++ /dev/null
@@ -1,7 +0,0 @@
-if OMAP44XX
-
-config SYS_SOC
- default "omap4"
-
-
-endif
diff --git a/arch/arm/mach-omap2/omap4/Makefile b/arch/arm/mach-omap2/omap4/Makefile
deleted file mode 100644
index 0ed3fc7..0000000
--- a/arch/arm/mach-omap2/omap4/Makefile
+++ /dev/null
@@ -1,11 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2000-2010
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-
-obj-y += boot.o
-obj-y += sdram_elpida.o
-obj-y += hwinit.o
-obj-y += emif.o
-obj-y += prcm-regs.o
-obj-y += hw_data.o
diff --git a/arch/arm/mach-omap2/omap4/boot.c b/arch/arm/mach-omap2/omap4/boot.c
deleted file mode 100644
index a60249f..0000000
--- a/arch/arm/mach-omap2/omap4/boot.c
+++ /dev/null
@@ -1,103 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * OMAP4 boot
- *
- * Copyright (C) 2015 Paul Kocialkowski <contact@paulk.fr>
- */
-
-#include <asm/io.h>
-#include <asm/omap_common.h>
-#include <asm/arch/sys_proto.h>
-#include <spl.h>
-
-static u32 boot_devices[] = {
- BOOT_DEVICE_MMC2,
- BOOT_DEVICE_XIP,
- BOOT_DEVICE_XIPWAIT,
- BOOT_DEVICE_NAND,
- BOOT_DEVICE_XIPWAIT,
- BOOT_DEVICE_MMC1,
- BOOT_DEVICE_ONENAND,
- BOOT_DEVICE_ONENAND,
- BOOT_DEVICE_MMC2,
- BOOT_DEVICE_ONENAND,
- BOOT_DEVICE_XIPWAIT,
- BOOT_DEVICE_NAND,
- BOOT_DEVICE_NAND,
- BOOT_DEVICE_MMC1,
- BOOT_DEVICE_ONENAND,
- BOOT_DEVICE_MMC2,
- BOOT_DEVICE_XIP,
- BOOT_DEVICE_XIPWAIT,
- BOOT_DEVICE_NAND,
- BOOT_DEVICE_MMC1,
- BOOT_DEVICE_MMC1,
- BOOT_DEVICE_ONENAND,
- BOOT_DEVICE_MMC2,
- BOOT_DEVICE_XIP,
- BOOT_DEVICE_MMC2_2,
- BOOT_DEVICE_NAND,
- BOOT_DEVICE_MMC2_2,
- BOOT_DEVICE_MMC1,
- BOOT_DEVICE_MMC2_2,
- BOOT_DEVICE_MMC2_2,
- BOOT_DEVICE_NONE,
- BOOT_DEVICE_XIPWAIT,
-};
-
-u32 omap_sys_boot_device(void)
-{
- u32 sys_boot;
-
- /* Grab the first 5 bits of the status register for SYS_BOOT. */
- sys_boot = readl((u32 *) (*ctrl)->control_status) & ((1 << 5) - 1);
-
- if (sys_boot >= (sizeof(boot_devices) / sizeof(u32)))
- return BOOT_DEVICE_NONE;
-
- return boot_devices[sys_boot];
-}
-
-int omap_reboot_mode(char *mode, unsigned int length)
-{
- unsigned int limit;
- unsigned int i;
-
- if (length < 2)
- return -1;
-
- if (!warm_reset())
- return -1;
-
- limit = (length < OMAP_REBOOT_REASON_SIZE) ? length :
- OMAP_REBOOT_REASON_SIZE;
-
- for (i = 0; i < (limit - 1); i++)
- mode[i] = readb((u8 *)(OMAP44XX_SAR_RAM_BASE +
- OMAP_REBOOT_REASON_OFFSET + i));
-
- mode[i] = '\0';
-
- return 0;
-}
-
-int omap_reboot_mode_clear(void)
-{
- writeb(0, (u8 *)(OMAP44XX_SAR_RAM_BASE + OMAP_REBOOT_REASON_OFFSET));
-
- return 0;
-}
-
-int omap_reboot_mode_store(char *mode)
-{
- unsigned int i;
-
- for (i = 0; i < (OMAP_REBOOT_REASON_SIZE - 1) && mode[i] != '\0'; i++)
- writeb(mode[i], (u8 *)(OMAP44XX_SAR_RAM_BASE +
- OMAP_REBOOT_REASON_OFFSET + i));
-
- writeb('\0', (u8 *)(OMAP44XX_SAR_RAM_BASE +
- OMAP_REBOOT_REASON_OFFSET + i));
-
- return 0;
-}
diff --git a/arch/arm/mach-omap2/omap4/emif.c b/arch/arm/mach-omap2/omap4/emif.c
deleted file mode 100644
index 5b0d3b5..0000000
--- a/arch/arm/mach-omap2/omap4/emif.c
+++ /dev/null
@@ -1,109 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * EMIF programming
- *
- * (C) Copyright 2010
- * Texas Instruments, <www.ti.com>
- *
- * Aneesh V <aneesh@ti.com>
- */
-
-#include <asm/emif.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/utils.h>
-
-#ifndef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
-u32 *const T_num = (u32 *)OMAP_SRAM_SCRATCH_EMIF_T_NUM;
-u32 *const T_den = (u32 *)OMAP_SRAM_SCRATCH_EMIF_T_DEN;
-#endif
-
-#ifdef CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
-/* Base AC Timing values specified by JESD209-2 for 400MHz operation */
-static const struct lpddr2_ac_timings timings_jedec_400_mhz = {
- .max_freq = 400000000,
- .RL = 6,
- .tRPab = 21,
- .tRCD = 18,
- .tWR = 15,
- .tRASmin = 42,
- .tRRD = 10,
- .tWTRx2 = 15,
- .tXSR = 140,
- .tXPx2 = 15,
- .tRFCab = 130,
- .tRTPx2 = 15,
- .tCKE = 3,
- .tCKESR = 15,
- .tZQCS = 90,
- .tZQCL = 360,
- .tZQINIT = 1000,
- .tDQSCKMAXx2 = 11,
- .tRASmax = 70,
- .tFAW = 50
-};
-
-/* Base AC Timing values specified by JESD209-2 for 200 MHz operation */
-static const struct lpddr2_ac_timings timings_jedec_200_mhz = {
- .max_freq = 200000000,
- .RL = 3,
- .tRPab = 21,
- .tRCD = 18,
- .tWR = 15,
- .tRASmin = 42,
- .tRRD = 10,
- .tWTRx2 = 20,
- .tXSR = 140,
- .tXPx2 = 15,
- .tRFCab = 130,
- .tRTPx2 = 15,
- .tCKE = 3,
- .tCKESR = 15,
- .tZQCS = 90,
- .tZQCL = 360,
- .tZQINIT = 1000,
- .tDQSCKMAXx2 = 11,
- .tRASmax = 70,
- .tFAW = 50
-};
-
-/*
- * Min tCK values specified by JESD209-2
- * Min tCK specifies the minimum duration of some AC timing parameters in terms
- * of the number of cycles. If the calculated number of cycles based on the
- * absolute time value is less than the min tCK value, min tCK value should
- * be used instead. This typically happens at low frequencies.
- */
-static const struct lpddr2_min_tck min_tck_jedec = {
- .tRL = 3,
- .tRP_AB = 3,
- .tRCD = 3,
- .tWR = 3,
- .tRAS_MIN = 3,
- .tRRD = 2,
- .tWTR = 2,
- .tXP = 2,
- .tRTP = 2,
- .tCKE = 3,
- .tCKESR = 3,
- .tFAW = 8
-};
-
-static const struct lpddr2_ac_timings *jedec_ac_timings[MAX_NUM_SPEEDBINS] = {
- &timings_jedec_200_mhz,
- &timings_jedec_400_mhz
-};
-
-const struct lpddr2_device_timings jedec_default_timings = {
- .ac_timings = jedec_ac_timings,
- .min_tck = &min_tck_jedec
-};
-
-void emif_get_device_timings(u32 emif_nr,
- const struct lpddr2_device_timings **cs0_device_timings,
- const struct lpddr2_device_timings **cs1_device_timings)
-{
- /* Assume Identical devices on EMIF1 & EMIF2 */
- *cs0_device_timings = &jedec_default_timings;
- *cs1_device_timings = &jedec_default_timings;
-}
-#endif /* CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS */
diff --git a/arch/arm/mach-omap2/omap4/hw_data.c b/arch/arm/mach-omap2/omap4/hw_data.c
deleted file mode 100644
index a81d765..0000000
--- a/arch/arm/mach-omap2/omap4/hw_data.c
+++ /dev/null
@@ -1,460 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- *
- * HW data initialization for OMAP4
- *
- * (C) Copyright 2013
- * Texas Instruments, <www.ti.com>
- *
- * Sricharan R <r.sricharan@ti.com>
- */
-#include <asm/arch/omap.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/omap_common.h>
-#include <asm/arch/clock.h>
-#include <asm/omap_gpio.h>
-#include <asm/io.h>
-
-struct prcm_regs const **prcm =
- (struct prcm_regs const **) OMAP_SRAM_SCRATCH_PRCM_PTR;
-struct dplls const **dplls_data =
- (struct dplls const **) OMAP_SRAM_SCRATCH_DPLLS_PTR;
-struct vcores_data const **omap_vcores =
- (struct vcores_data const **) OMAP_SRAM_SCRATCH_VCORES_PTR;
-struct omap_sys_ctrl_regs const **ctrl =
- (struct omap_sys_ctrl_regs const **)OMAP_SRAM_SCRATCH_SYS_CTRL;
-
-/*
- * The M & N values in the following tables are created using the
- * following tool:
- * tools/omap/clocks_get_m_n.c
- * Please use this tool for creating the table for any new frequency.
- */
-
-/*
- * dpll locked at 1400 MHz MPU clk at 700 MHz(OPP100) - DCC OFF
- * OMAP4460 OPP_NOM frequency
- */
-static const struct dpll_params mpu_dpll_params_1400mhz[NUM_SYS_CLKS] = {
- {175, 2, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 12 MHz */
- {700, 12, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 13 MHz */
- {125, 2, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 16.8 MHz */
- {401, 10, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 19.2 MHz */
- {350, 12, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 26 MHz */
- {700, 26, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 27 MHz */
- {638, 34, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1} /* 38.4 MHz */
-};
-
-/*
- * dpll locked at 1600 MHz - MPU clk at 800 MHz(OPP Turbo 4430)
- * OMAP4430 OPP_TURBO frequency
- * OMAP4470 OPP_NOM frequency
- */
-static const struct dpll_params mpu_dpll_params_1600mhz[NUM_SYS_CLKS] = {
- {200, 2, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 12 MHz */
- {800, 12, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 13 MHz */
- {619, 12, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 16.8 MHz */
- {125, 2, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 19.2 MHz */
- {400, 12, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 26 MHz */
- {800, 26, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 27 MHz */
- {125, 5, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1} /* 38.4 MHz */
-};
-
-/*
- * dpll locked at 1200 MHz - MPU clk at 600 MHz
- * OMAP4430 OPP_NOM frequency
- */
-static const struct dpll_params mpu_dpll_params_1200mhz[NUM_SYS_CLKS] = {
- {50, 0, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 12 MHz */
- {600, 12, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 13 MHz */
- {250, 6, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 16.8 MHz */
- {125, 3, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 19.2 MHz */
- {300, 12, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 26 MHz */
- {200, 8, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 27 MHz */
- {125, 7, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1} /* 38.4 MHz */
-};
-
-/* OMAP4460 OPP_NOM frequency */
-/* OMAP4470 OPP_NOM (Low Power) frequency */
-static const struct dpll_params core_dpll_params_1600mhz[NUM_SYS_CLKS] = {
- {200, 2, 1, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 12 MHz */
- {800, 12, 1, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 13 MHz */
- {619, 12, 1, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 16.8 MHz */
- {125, 2, 1, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 19.2 MHz */
- {400, 12, 1, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 26 MHz */
- {800, 26, 1, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 27 MHz */
- {125, 5, 1, 5, 8, 4, 6, 5, -1, -1, -1, -1} /* 38.4 MHz */
-};
-
-/* OMAP4430 ES1 OPP_NOM frequency */
-static const struct dpll_params core_dpll_params_es1_1524mhz[NUM_SYS_CLKS] = {
- {127, 1, 1, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 12 MHz */
- {762, 12, 1, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 13 MHz */
- {635, 13, 1, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 16.8 MHz */
- {635, 15, 1, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 19.2 MHz */
- {381, 12, 1, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 26 MHz */
- {254, 8, 1, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 27 MHz */
- {496, 24, 1, 5, 8, 4, 6, 5, -1, -1, -1, -1} /* 38.4 MHz */
-};
-
-/* OMAP4430 ES2.X OPP_NOM frequency */
-static const struct dpll_params
- core_dpll_params_es2_1600mhz_ddr200mhz[NUM_SYS_CLKS] = {
- {200, 2, 2, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 12 MHz */
- {800, 12, 2, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 13 MHz */
- {619, 12, 2, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 16.8 MHz */
- {125, 2, 2, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 19.2 MHz */
- {400, 12, 2, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 26 MHz */
- {800, 26, 2, 5, 8, 4, 6, 5, -1, -1, -1, -1}, /* 27 MHz */
- {125, 5, 2, 5, 8, 4, 6, 5, -1, -1, -1, -1} /* 38.4 MHz */
-};
-
-static const struct dpll_params per_dpll_params_1536mhz[NUM_SYS_CLKS] = {
- {64, 0, 8, 6, 12, 9, 4, 5, -1, -1, -1, -1}, /* 12 MHz */
- {768, 12, 8, 6, 12, 9, 4, 5, -1, -1, -1, -1}, /* 13 MHz */
- {320, 6, 8, 6, 12, 9, 4, 5, -1, -1, -1, -1}, /* 16.8 MHz */
- {40, 0, 8, 6, 12, 9, 4, 5, -1, -1, -1, -1}, /* 19.2 MHz */
- {384, 12, 8, 6, 12, 9, 4, 5, -1, -1, -1, -1}, /* 26 MHz */
- {256, 8, 8, 6, 12, 9, 4, 5, -1, -1, -1, -1}, /* 27 MHz */
- {20, 0, 8, 6, 12, 9, 4, 5, -1, -1, -1, -1} /* 38.4 MHz */
-};
-
-static const struct dpll_params iva_dpll_params_1862mhz[NUM_SYS_CLKS] = {
- {931, 11, -1, -1, 4, 7, -1, -1, -1, -1, -1, -1}, /* 12 MHz */
- {931, 12, -1, -1, 4, 7, -1, -1, -1, -1, -1, -1}, /* 13 MHz */
- {665, 11, -1, -1, 4, 7, -1, -1, -1, -1, -1, -1}, /* 16.8 MHz */
- {727, 14, -1, -1, 4, 7, -1, -1, -1, -1, -1, -1}, /* 19.2 MHz */
- {931, 25, -1, -1, 4, 7, -1, -1, -1, -1, -1, -1}, /* 26 MHz */
- {931, 26, -1, -1, 4, 7, -1, -1, -1, -1, -1, -1}, /* 27 MHz */
- {291, 11, -1, -1, 4, 7, -1, -1, -1, -1, -1, -1} /* 38.4 MHz */
-};
-
-/* ABE M & N values with sys_clk as source */
-#ifdef CONFIG_SYS_OMAP_ABE_SYSCK
-static const struct dpll_params
- abe_dpll_params_sysclk_196608khz[NUM_SYS_CLKS] = {
- {49, 5, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 12 MHz */
- {68, 8, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 13 MHz */
- {35, 5, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 16.8 MHz */
- {46, 8, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 19.2 MHz */
- {34, 8, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 26 MHz */
- {29, 7, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 27 MHz */
- {64, 24, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1} /* 38.4 MHz */
-};
-#else
-/* ABE M & N values with 32K clock as source */
-static const struct dpll_params abe_dpll_params_32k_196608khz = {
- 750, 0, 1, 1, -1, -1, -1, -1, -1, -1, -1, -1
-};
-#endif
-
-static const struct dpll_params usb_dpll_params_1920mhz[NUM_SYS_CLKS] = {
- {80, 0, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 12 MHz */
- {960, 12, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 13 MHz */
- {400, 6, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 16.8 MHz */
- {50, 0, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 19.2 MHz */
- {480, 12, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 26 MHz */
- {320, 8, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1}, /* 27 MHz */
- {25, 0, 2, -1, -1, -1, -1, -1, -1, -1, -1, -1} /* 38.4 MHz */
-};
-
-struct dplls omap4430_dplls_es1 = {
- .mpu = mpu_dpll_params_1200mhz,
- .core = core_dpll_params_es1_1524mhz,
- .per = per_dpll_params_1536mhz,
- .iva = iva_dpll_params_1862mhz,
-#ifdef CONFIG_SYS_OMAP_ABE_SYSCK
- .abe = abe_dpll_params_sysclk_196608khz,
-#else
- .abe = &abe_dpll_params_32k_196608khz,
-#endif
- .usb = usb_dpll_params_1920mhz,
- .ddr = NULL
-};
-
-struct dplls omap4430_dplls_es20 = {
- .mpu = mpu_dpll_params_1200mhz,
- .core = core_dpll_params_es2_1600mhz_ddr200mhz,
- .per = per_dpll_params_1536mhz,
- .iva = iva_dpll_params_1862mhz,
-#ifdef CONFIG_SYS_OMAP_ABE_SYSCK
- .abe = abe_dpll_params_sysclk_196608khz,
-#else
- .abe = &abe_dpll_params_32k_196608khz,
-#endif
- .usb = usb_dpll_params_1920mhz,
- .ddr = NULL
-};
-
-struct dplls omap4430_dplls = {
- .mpu = mpu_dpll_params_1200mhz,
- .core = core_dpll_params_1600mhz,
- .per = per_dpll_params_1536mhz,
- .iva = iva_dpll_params_1862mhz,
-#ifdef CONFIG_SYS_OMAP_ABE_SYSCK
- .abe = abe_dpll_params_sysclk_196608khz,
-#else
- .abe = &abe_dpll_params_32k_196608khz,
-#endif
- .usb = usb_dpll_params_1920mhz,
- .ddr = NULL
-};
-
-struct dplls omap4460_dplls = {
- .mpu = mpu_dpll_params_1400mhz,
- .core = core_dpll_params_1600mhz,
- .per = per_dpll_params_1536mhz,
- .iva = iva_dpll_params_1862mhz,
-#ifdef CONFIG_SYS_OMAP_ABE_SYSCK
- .abe = abe_dpll_params_sysclk_196608khz,
-#else
- .abe = &abe_dpll_params_32k_196608khz,
-#endif
- .usb = usb_dpll_params_1920mhz,
- .ddr = NULL
-};
-
-struct dplls omap4470_dplls = {
- .mpu = mpu_dpll_params_1600mhz,
- .core = core_dpll_params_1600mhz,
- .per = per_dpll_params_1536mhz,
- .iva = iva_dpll_params_1862mhz,
-#ifdef CONFIG_SYS_OMAP_ABE_SYSCK
- .abe = abe_dpll_params_sysclk_196608khz,
-#else
- .abe = &abe_dpll_params_32k_196608khz,
-#endif
- .usb = usb_dpll_params_1920mhz,
- .ddr = NULL
-};
-
-struct pmic_data twl6030_4430es1 = {
- .base_offset = PHOENIX_SMPS_BASE_VOLT_STD_MODE_UV,
- .step = 12660, /* 12.66 mV represented in uV */
- /* The code starts at 1 not 0 */
- .start_code = 1,
- .i2c_slave_addr = SMPS_I2C_SLAVE_ADDR,
- .pmic_bus_init = sri2c_init,
- .pmic_write = omap_vc_bypass_send_value,
-};
-
-/* twl6030 struct is used for TWL6030 and TWL6032 PMIC */
-struct pmic_data twl6030 = {
- .base_offset = PHOENIX_SMPS_BASE_VOLT_STD_MODE_WITH_OFFSET_UV,
- .step = 12660, /* 12.66 mV represented in uV */
- /* The code starts at 1 not 0 */
- .start_code = 1,
- .i2c_slave_addr = SMPS_I2C_SLAVE_ADDR,
- .pmic_bus_init = sri2c_init,
- .pmic_write = omap_vc_bypass_send_value,
-};
-
-struct pmic_data tps62361 = {
- .base_offset = TPS62361_BASE_VOLT_MV,
- .step = 10000, /* 10 mV represented in uV */
- .start_code = 0,
- .gpio = TPS62361_VSEL0_GPIO,
- .gpio_en = 1,
- .i2c_slave_addr = SMPS_I2C_SLAVE_ADDR,
- .pmic_bus_init = sri2c_init,
- .pmic_write = omap_vc_bypass_send_value,
-};
-
-struct vcores_data omap4430_volts_es1 = {
- .mpu.value[OPP_NOM] = 1325,
- .mpu.addr = SMPS_REG_ADDR_VCORE1,
- .mpu.pmic = &twl6030_4430es1,
-
- .core.value[OPP_NOM] = 1200,
- .core.addr = SMPS_REG_ADDR_VCORE3,
- .core.pmic = &twl6030_4430es1,
-
- .mm.value[OPP_NOM] = 1200,
- .mm.addr = SMPS_REG_ADDR_VCORE2,
- .mm.pmic = &twl6030_4430es1,
-};
-
-struct vcores_data omap4430_volts = {
- .mpu.value[OPP_NOM] = 1325,
- .mpu.addr = SMPS_REG_ADDR_VCORE1,
- .mpu.pmic = &twl6030,
-
- .core.value[OPP_NOM] = 1200,
- .core.addr = SMPS_REG_ADDR_VCORE3,
- .core.pmic = &twl6030,
-
- .mm.value[OPP_NOM] = 1200,
- .mm.addr = SMPS_REG_ADDR_VCORE2,
- .mm.pmic = &twl6030,
-};
-
-struct vcores_data omap4460_volts = {
- .mpu.value[OPP_NOM] = 1203,
- .mpu.addr = TPS62361_REG_ADDR_SET1,
- .mpu.pmic = &tps62361,
-
- .core.value[OPP_NOM] = 1200,
- .core.addr = SMPS_REG_ADDR_VCORE1,
- .core.pmic = &twl6030,
-
- .mm.value[OPP_NOM] = 1200,
- .mm.addr = SMPS_REG_ADDR_VCORE2,
- .mm.pmic = &twl6030,
-};
-
-/*
- * Take closest integer part of the mV value corresponding to a TWL6032 SMPS
- * voltage selection code. Aligned with OMAP4470 ES1.0 OCA V.0.7.
- */
-struct vcores_data omap4470_volts = {
- .mpu.value[OPP_NOM] = 1202,
- .mpu.addr = SMPS_REG_ADDR_SMPS1,
- .mpu.pmic = &twl6030,
-
- .core.value[OPP_NOM] = 1126,
- .core.addr = SMPS_REG_ADDR_SMPS2,
- .core.pmic = &twl6030,
-
- .mm.value[OPP_NOM] = 1139,
- .mm.addr = SMPS_REG_ADDR_SMPS5,
- .mm.pmic = &twl6030,
-};
-
-/*
- * Enable essential clock domains, modules and
- * do some additional special settings needed
- */
-void enable_basic_clocks(void)
-{
- u32 const clk_domains_essential[] = {
- (*prcm)->cm_l4per_clkstctrl,
- (*prcm)->cm_l3init_clkstctrl,
- (*prcm)->cm_memif_clkstctrl,
- (*prcm)->cm_l4cfg_clkstctrl,
- 0
- };
-
- u32 const clk_modules_hw_auto_essential[] = {
- (*prcm)->cm_l3_gpmc_clkctrl,
- (*prcm)->cm_memif_emif_1_clkctrl,
- (*prcm)->cm_memif_emif_2_clkctrl,
- (*prcm)->cm_l4cfg_l4_cfg_clkctrl,
- (*prcm)->cm_wkup_gpio1_clkctrl,
- (*prcm)->cm_l4per_gpio2_clkctrl,
- (*prcm)->cm_l4per_gpio3_clkctrl,
- (*prcm)->cm_l4per_gpio4_clkctrl,
- (*prcm)->cm_l4per_gpio5_clkctrl,
- (*prcm)->cm_l4per_gpio6_clkctrl,
- 0
- };
-
- u32 const clk_modules_explicit_en_essential[] = {
- (*prcm)->cm_wkup_gptimer1_clkctrl,
- (*prcm)->cm_l3init_hsmmc1_clkctrl,
- (*prcm)->cm_l3init_hsmmc2_clkctrl,
- (*prcm)->cm_l4per_gptimer2_clkctrl,
- (*prcm)->cm_wkup_wdtimer2_clkctrl,
- (*prcm)->cm_l4per_uart3_clkctrl,
- (*prcm)->cm_l4per_i2c1_clkctrl,
- (*prcm)->cm_l4per_i2c2_clkctrl,
- (*prcm)->cm_l4per_i2c3_clkctrl,
- (*prcm)->cm_l4per_i2c4_clkctrl,
- 0
- };
-
- /* Enable optional additional functional clock for GPIO4 */
- setbits_le32((*prcm)->cm_l4per_gpio4_clkctrl,
- GPIO4_CLKCTRL_OPTFCLKEN_MASK);
-
- /* Enable 96 MHz clock for MMC1 & MMC2 */
- setbits_le32((*prcm)->cm_l3init_hsmmc1_clkctrl,
- HSMMC_CLKCTRL_CLKSEL_MASK);
- setbits_le32((*prcm)->cm_l3init_hsmmc2_clkctrl,
- HSMMC_CLKCTRL_CLKSEL_MASK);
-
- /* Select 32KHz clock as the source of GPTIMER1 */
- setbits_le32((*prcm)->cm_wkup_gptimer1_clkctrl,
- GPTIMER1_CLKCTRL_CLKSEL_MASK);
-
- /* Enable optional 48M functional clock for USB PHY */
- setbits_le32((*prcm)->cm_l3init_usbphy_clkctrl,
- USBPHY_CLKCTRL_OPTFCLKEN_PHY_48M_MASK);
-
- /* Enable 32 KHz clock for USB PHY */
- setbits_le32((*prcm)->cm_coreaon_usb_phy1_core_clkctrl,
- USBPHY_CORE_CLKCTRL_OPTFCLKEN_CLK32K);
-
- do_enable_clocks(clk_domains_essential,
- clk_modules_hw_auto_essential,
- clk_modules_explicit_en_essential,
- 1);
-}
-
-void enable_basic_uboot_clocks(void)
-{
- u32 const clk_domains_essential[] = {
- 0
- };
-
- u32 const clk_modules_hw_auto_essential[] = {
- (*prcm)->cm_l3init_hsusbotg_clkctrl,
- (*prcm)->cm_l3init_usbphy_clkctrl,
- (*prcm)->cm_clksel_usb_60mhz,
- (*prcm)->cm_l3init_hsusbtll_clkctrl,
- 0
- };
-
- u32 const clk_modules_explicit_en_essential[] = {
- (*prcm)->cm_l4per_mcspi1_clkctrl,
- (*prcm)->cm_l3init_hsusbhost_clkctrl,
- 0
- };
-
- do_enable_clocks(clk_domains_essential,
- clk_modules_hw_auto_essential,
- clk_modules_explicit_en_essential,
- 1);
-}
-
-void hw_data_init(void)
-{
- u32 omap_rev = omap_revision();
-
- (*prcm) = &omap4_prcm;
-
- switch (omap_rev) {
-
- case OMAP4430_ES1_0:
- *dplls_data = &omap4430_dplls_es1;
- *omap_vcores = &omap4430_volts_es1;
- break;
-
- case OMAP4430_ES2_0:
- *dplls_data = &omap4430_dplls_es20;
- *omap_vcores = &omap4430_volts;
- break;
-
- case OMAP4430_ES2_1:
- case OMAP4430_ES2_2:
- case OMAP4430_ES2_3:
- *dplls_data = &omap4430_dplls;
- *omap_vcores = &omap4430_volts;
- break;
-
- case OMAP4460_ES1_0:
- case OMAP4460_ES1_1:
- *dplls_data = &omap4460_dplls;
- *omap_vcores = &omap4460_volts;
- break;
-
- case OMAP4470_ES1_0:
- *dplls_data = &omap4470_dplls;
- *omap_vcores = &omap4470_volts;
- break;
-
- default:
- printf("\n INVALID OMAP REVISION ");
- }
-
- *ctrl = &omap4_ctrl;
-}
diff --git a/arch/arm/mach-omap2/omap4/hwinit.c b/arch/arm/mach-omap2/omap4/hwinit.c
deleted file mode 100644
index e3e6cc8..0000000
--- a/arch/arm/mach-omap2/omap4/hwinit.c
+++ /dev/null
@@ -1,186 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- *
- * Common functions for OMAP4 based boards
- *
- * (C) Copyright 2010
- * Texas Instruments, <www.ti.com>
- *
- * Author :
- * Aneesh V <aneesh@ti.com>
- * Steve Sakoman <steve@sakoman.com>
- */
-#include <palmas.h>
-#include <asm/armv7.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/sys_proto.h>
-#include <linux/sizes.h>
-#include <asm/emif.h>
-#include <asm/arch/gpio.h>
-#include <asm/omap_common.h>
-
-u32 *const omap_si_rev = (u32 *)OMAP_SRAM_SCRATCH_OMAP_REV;
-
-static const struct gpio_bank gpio_bank_44xx[6] = {
- { (void *)OMAP44XX_GPIO1_BASE },
- { (void *)OMAP44XX_GPIO2_BASE },
- { (void *)OMAP44XX_GPIO3_BASE },
- { (void *)OMAP44XX_GPIO4_BASE },
- { (void *)OMAP44XX_GPIO5_BASE },
- { (void *)OMAP44XX_GPIO6_BASE },
-};
-
-const struct gpio_bank *const omap_gpio_bank = gpio_bank_44xx;
-
-#ifdef CONFIG_SPL_BUILD
-/*
- * Some tuning of IOs for optimal power and performance
- */
-void do_io_settings(void)
-{
- u32 lpddr2io;
-
- u32 omap4_rev = omap_revision();
-
- if (omap4_rev == OMAP4430_ES1_0)
- lpddr2io = CONTROL_LPDDR2IO_SLEW_125PS_DRV8_PULL_DOWN;
- else if (omap4_rev == OMAP4430_ES2_0)
- lpddr2io = CONTROL_LPDDR2IO_SLEW_325PS_DRV8_GATE_KEEPER;
- else
- lpddr2io = CONTROL_LPDDR2IO_SLEW_315PS_DRV12_PULL_DOWN;
-
- /* EMIF1 */
- writel(lpddr2io, (*ctrl)->control_lpddr2io1_0);
- writel(lpddr2io, (*ctrl)->control_lpddr2io1_1);
- /* No pull for GR10 as per hw team's recommendation */
- writel(lpddr2io & ~LPDDR2IO_GR10_WD_MASK,
- (*ctrl)->control_lpddr2io1_2);
- writel(CONTROL_LPDDR2IO_3_VAL, (*ctrl)->control_lpddr2io1_3);
-
- /* EMIF2 */
- writel(lpddr2io, (*ctrl)->control_lpddr2io2_0);
- writel(lpddr2io, (*ctrl)->control_lpddr2io2_1);
- /* No pull for GR10 as per hw team's recommendation */
- writel(lpddr2io & ~LPDDR2IO_GR10_WD_MASK,
- (*ctrl)->control_lpddr2io2_2);
- writel(CONTROL_LPDDR2IO_3_VAL, (*ctrl)->control_lpddr2io2_3);
-
- /*
- * Some of these settings (TRIM values) come from eFuse and are
- * in turn programmed in the eFuse at manufacturing time after
- * calibration of the device. Do the software over-ride only if
- * the device is not correctly trimmed
- */
- if (!(readl((*ctrl)->control_std_fuse_opp_bgap) & 0xFFFF)) {
-
- writel(LDOSRAM_VOLT_CTRL_OVERRIDE,
- (*ctrl)->control_ldosram_iva_voltage_ctrl);
-
- writel(LDOSRAM_VOLT_CTRL_OVERRIDE,
- (*ctrl)->control_ldosram_mpu_voltage_ctrl);
-
- writel(LDOSRAM_VOLT_CTRL_OVERRIDE,
- (*ctrl)->control_ldosram_core_voltage_ctrl);
- }
-
- /*
- * Over-ride the register
- * i. unconditionally for all 4430
- * ii. only if un-trimmed for 4460
- */
- if (!readl((*ctrl)->control_efuse_1))
- writel(CONTROL_EFUSE_1_OVERRIDE, (*ctrl)->control_efuse_1);
-
- if ((omap4_rev < OMAP4460_ES1_0) || !readl((*ctrl)->control_efuse_2))
- writel(CONTROL_EFUSE_2_OVERRIDE, (*ctrl)->control_efuse_2);
-}
-#endif /* CONFIG_SPL_BUILD */
-
-/* dummy fuction for omap4 */
-void config_data_eye_leveling_samples(u32 emif_base)
-{
-}
-
-void init_omap_revision(void)
-{
- /*
- * For some of the ES2/ES1 boards ID_CODE is not reliable:
- * Also, ES1 and ES2 have different ARM revisions
- * So use ARM revision for identification
- */
- unsigned int arm_rev = cortex_rev();
-
- switch (arm_rev) {
- case MIDR_CORTEX_A9_R0P1:
- *omap_si_rev = OMAP4430_ES1_0;
- break;
- case MIDR_CORTEX_A9_R1P2:
- switch (readl(CONTROL_ID_CODE)) {
- case OMAP4_CONTROL_ID_CODE_ES2_0:
- *omap_si_rev = OMAP4430_ES2_0;
- break;
- case OMAP4_CONTROL_ID_CODE_ES2_1:
- *omap_si_rev = OMAP4430_ES2_1;
- break;
- case OMAP4_CONTROL_ID_CODE_ES2_2:
- *omap_si_rev = OMAP4430_ES2_2;
- break;
- default:
- *omap_si_rev = OMAP4430_ES2_0;
- break;
- }
- break;
- case MIDR_CORTEX_A9_R1P3:
- *omap_si_rev = OMAP4430_ES2_3;
- break;
- case MIDR_CORTEX_A9_R2P10:
- switch (readl(CONTROL_ID_CODE)) {
- case OMAP4470_CONTROL_ID_CODE_ES1_0:
- *omap_si_rev = OMAP4470_ES1_0;
- break;
- case OMAP4460_CONTROL_ID_CODE_ES1_1:
- *omap_si_rev = OMAP4460_ES1_1;
- break;
- case OMAP4460_CONTROL_ID_CODE_ES1_0:
- default:
- *omap_si_rev = OMAP4460_ES1_0;
- break;
- }
- break;
- default:
- *omap_si_rev = OMAP4430_SILICON_ID_INVALID;
- break;
- }
-}
-
-void omap_die_id(unsigned int *die_id)
-{
- die_id[0] = readl((*ctrl)->control_std_fuse_die_id_0);
- die_id[1] = readl((*ctrl)->control_std_fuse_die_id_1);
- die_id[2] = readl((*ctrl)->control_std_fuse_die_id_2);
- die_id[3] = readl((*ctrl)->control_std_fuse_die_id_3);
-}
-
-#ifndef CONFIG_SYS_L2CACHE_OFF
-void v7_outer_cache_enable(void)
-{
- omap_smc1(OMAP4_SERVICE_PL310_CONTROL_REG_SET, 1);
-}
-
-void v7_outer_cache_disable(void)
-{
- omap_smc1(OMAP4_SERVICE_PL310_CONTROL_REG_SET, 0);
-}
-#endif /* !CONFIG_SYS_L2CACHE_OFF */
-
-void vmmc_pbias_config(uint voltage)
-{
- u32 value = 0;
-
- value = readl((*ctrl)->control_pbiaslite);
- value &= ~(MMC1_PBIASLITE_PWRDNZ | MMC1_PWRDNZ);
- writel(value, (*ctrl)->control_pbiaslite);
- value = readl((*ctrl)->control_pbiaslite);
- value |= MMC1_PBIASLITE_VMODE | MMC1_PBIASLITE_PWRDNZ | MMC1_PWRDNZ;
- writel(value, (*ctrl)->control_pbiaslite);
-}
diff --git a/arch/arm/mach-omap2/omap4/prcm-regs.c b/arch/arm/mach-omap2/omap4/prcm-regs.c
deleted file mode 100644
index eaf98b3..0000000
--- a/arch/arm/mach-omap2/omap4/prcm-regs.c
+++ /dev/null
@@ -1,306 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- *
- * HW regs data for OMAP4
- *
- * (C) Copyright 2013
- * Texas Instruments, <www.ti.com>
- *
- * Sricharan R <r.sricharan@ti.com>
- */
-
-#include <asm/omap_common.h>
-
-struct prcm_regs const omap4_prcm = {
- /* cm1.ckgen */
- .cm_clksel_core = 0x4a004100,
- .cm_clksel_abe = 0x4a004108,
- .cm_dll_ctrl = 0x4a004110,
- .cm_clkmode_dpll_core = 0x4a004120,
- .cm_idlest_dpll_core = 0x4a004124,
- .cm_autoidle_dpll_core = 0x4a004128,
- .cm_clksel_dpll_core = 0x4a00412c,
- .cm_div_m2_dpll_core = 0x4a004130,
- .cm_div_m3_dpll_core = 0x4a004134,
- .cm_div_m4_dpll_core = 0x4a004138,
- .cm_div_m5_dpll_core = 0x4a00413c,
- .cm_div_m6_dpll_core = 0x4a004140,
- .cm_div_m7_dpll_core = 0x4a004144,
- .cm_ssc_deltamstep_dpll_core = 0x4a004148,
- .cm_ssc_modfreqdiv_dpll_core = 0x4a00414c,
- .cm_emu_override_dpll_core = 0x4a004150,
- .cm_clkmode_dpll_mpu = 0x4a004160,
- .cm_idlest_dpll_mpu = 0x4a004164,
- .cm_autoidle_dpll_mpu = 0x4a004168,
- .cm_clksel_dpll_mpu = 0x4a00416c,
- .cm_div_m2_dpll_mpu = 0x4a004170,
- .cm_ssc_deltamstep_dpll_mpu = 0x4a004188,
- .cm_ssc_modfreqdiv_dpll_mpu = 0x4a00418c,
- .cm_bypclk_dpll_mpu = 0x4a00419c,
- .cm_clkmode_dpll_iva = 0x4a0041a0,
- .cm_idlest_dpll_iva = 0x4a0041a4,
- .cm_autoidle_dpll_iva = 0x4a0041a8,
- .cm_clksel_dpll_iva = 0x4a0041ac,
- .cm_div_m4_dpll_iva = 0x4a0041b8,
- .cm_div_m5_dpll_iva = 0x4a0041bc,
- .cm_ssc_deltamstep_dpll_iva = 0x4a0041c8,
- .cm_ssc_modfreqdiv_dpll_iva = 0x4a0041cc,
- .cm_bypclk_dpll_iva = 0x4a0041dc,
- .cm_clkmode_dpll_abe = 0x4a0041e0,
- .cm_idlest_dpll_abe = 0x4a0041e4,
- .cm_autoidle_dpll_abe = 0x4a0041e8,
- .cm_clksel_dpll_abe = 0x4a0041ec,
- .cm_div_m2_dpll_abe = 0x4a0041f0,
- .cm_div_m3_dpll_abe = 0x4a0041f4,
- .cm_ssc_deltamstep_dpll_abe = 0x4a004208,
- .cm_ssc_modfreqdiv_dpll_abe = 0x4a00420c,
- .cm_clkmode_dpll_ddrphy = 0x4a004220,
- .cm_idlest_dpll_ddrphy = 0x4a004224,
- .cm_autoidle_dpll_ddrphy = 0x4a004228,
- .cm_clksel_dpll_ddrphy = 0x4a00422c,
- .cm_div_m2_dpll_ddrphy = 0x4a004230,
- .cm_div_m4_dpll_ddrphy = 0x4a004238,
- .cm_div_m5_dpll_ddrphy = 0x4a00423c,
- .cm_div_m6_dpll_ddrphy = 0x4a004240,
- .cm_ssc_deltamstep_dpll_ddrphy = 0x4a004248,
- .cm_shadow_freq_config1 = 0x4a004260,
- .cm_mpu_mpu_clkctrl = 0x4a004320,
-
- /* cm1.dsp */
- .cm_dsp_clkstctrl = 0x4a004400,
- .cm_dsp_dsp_clkctrl = 0x4a004420,
-
- /* cm1.abe */
- .cm1_abe_clkstctrl = 0x4a004500,
- .cm1_abe_l4abe_clkctrl = 0x4a004520,
- .cm1_abe_aess_clkctrl = 0x4a004528,
- .cm1_abe_pdm_clkctrl = 0x4a004530,
- .cm1_abe_dmic_clkctrl = 0x4a004538,
- .cm1_abe_mcasp_clkctrl = 0x4a004540,
- .cm1_abe_mcbsp1_clkctrl = 0x4a004548,
- .cm1_abe_mcbsp2_clkctrl = 0x4a004550,
- .cm1_abe_mcbsp3_clkctrl = 0x4a004558,
- .cm1_abe_slimbus_clkctrl = 0x4a004560,
- .cm1_abe_timer5_clkctrl = 0x4a004568,
- .cm1_abe_timer6_clkctrl = 0x4a004570,
- .cm1_abe_timer7_clkctrl = 0x4a004578,
- .cm1_abe_timer8_clkctrl = 0x4a004580,
- .cm1_abe_wdt3_clkctrl = 0x4a004588,
-
- /* cm2.ckgen */
- .cm_clksel_mpu_m3_iss_root = 0x4a008100,
- .cm_clksel_usb_60mhz = 0x4a008104,
- .cm_scale_fclk = 0x4a008108,
- .cm_core_dvfs_perf1 = 0x4a008110,
- .cm_core_dvfs_perf2 = 0x4a008114,
- .cm_core_dvfs_perf3 = 0x4a008118,
- .cm_core_dvfs_perf4 = 0x4a00811c,
- .cm_core_dvfs_current = 0x4a008124,
- .cm_iva_dvfs_perf_tesla = 0x4a008128,
- .cm_iva_dvfs_perf_ivahd = 0x4a00812c,
- .cm_iva_dvfs_perf_abe = 0x4a008130,
- .cm_iva_dvfs_current = 0x4a008138,
- .cm_clkmode_dpll_per = 0x4a008140,
- .cm_idlest_dpll_per = 0x4a008144,
- .cm_autoidle_dpll_per = 0x4a008148,
- .cm_clksel_dpll_per = 0x4a00814c,
- .cm_div_m2_dpll_per = 0x4a008150,
- .cm_div_m3_dpll_per = 0x4a008154,
- .cm_div_m4_dpll_per = 0x4a008158,
- .cm_div_m5_dpll_per = 0x4a00815c,
- .cm_div_m6_dpll_per = 0x4a008160,
- .cm_div_m7_dpll_per = 0x4a008164,
- .cm_ssc_deltamstep_dpll_per = 0x4a008168,
- .cm_ssc_modfreqdiv_dpll_per = 0x4a00816c,
- .cm_emu_override_dpll_per = 0x4a008170,
- .cm_clkmode_dpll_usb = 0x4a008180,
- .cm_idlest_dpll_usb = 0x4a008184,
- .cm_autoidle_dpll_usb = 0x4a008188,
- .cm_clksel_dpll_usb = 0x4a00818c,
- .cm_div_m2_dpll_usb = 0x4a008190,
- .cm_ssc_deltamstep_dpll_usb = 0x4a0081a8,
- .cm_ssc_modfreqdiv_dpll_usb = 0x4a0081ac,
- .cm_clkdcoldo_dpll_usb = 0x4a0081b4,
- .cm_clkmode_dpll_unipro = 0x4a0081c0,
- .cm_idlest_dpll_unipro = 0x4a0081c4,
- .cm_autoidle_dpll_unipro = 0x4a0081c8,
- .cm_clksel_dpll_unipro = 0x4a0081cc,
- .cm_div_m2_dpll_unipro = 0x4a0081d0,
- .cm_ssc_deltamstep_dpll_unipro = 0x4a0081e8,
- .cm_ssc_modfreqdiv_dpll_unipro = 0x4a0081ec,
- .cm_coreaon_usb_phy1_core_clkctrl = 0x4a008640,
-
- /* cm2.core */
- .cm_l3_1_clkstctrl = 0x4a008700,
- .cm_l3_1_dynamicdep = 0x4a008708,
- .cm_l3_1_l3_1_clkctrl = 0x4a008720,
- .cm_l3_2_clkstctrl = 0x4a008800,
- .cm_l3_2_dynamicdep = 0x4a008808,
- .cm_l3_2_l3_2_clkctrl = 0x4a008820,
- .cm_l3_gpmc_clkctrl = 0x4a008828,
- .cm_l3_2_ocmc_ram_clkctrl = 0x4a008830,
- .cm_mpu_m3_clkstctrl = 0x4a008900,
- .cm_mpu_m3_staticdep = 0x4a008904,
- .cm_mpu_m3_dynamicdep = 0x4a008908,
- .cm_mpu_m3_mpu_m3_clkctrl = 0x4a008920,
- .cm_sdma_clkstctrl = 0x4a008a00,
- .cm_sdma_staticdep = 0x4a008a04,
- .cm_sdma_dynamicdep = 0x4a008a08,
- .cm_sdma_sdma_clkctrl = 0x4a008a20,
- .cm_memif_clkstctrl = 0x4a008b00,
- .cm_memif_dmm_clkctrl = 0x4a008b20,
- .cm_memif_emif_fw_clkctrl = 0x4a008b28,
- .cm_memif_emif_1_clkctrl = 0x4a008b30,
- .cm_memif_emif_2_clkctrl = 0x4a008b38,
- .cm_memif_dll_clkctrl = 0x4a008b40,
- .cm_memif_emif_h1_clkctrl = 0x4a008b50,
- .cm_memif_emif_h2_clkctrl = 0x4a008b58,
- .cm_memif_dll_h_clkctrl = 0x4a008b60,
- .cm_c2c_clkstctrl = 0x4a008c00,
- .cm_c2c_staticdep = 0x4a008c04,
- .cm_c2c_dynamicdep = 0x4a008c08,
- .cm_c2c_sad2d_clkctrl = 0x4a008c20,
- .cm_c2c_modem_icr_clkctrl = 0x4a008c28,
- .cm_c2c_sad2d_fw_clkctrl = 0x4a008c30,
- .cm_l4cfg_clkstctrl = 0x4a008d00,
- .cm_l4cfg_dynamicdep = 0x4a008d08,
- .cm_l4cfg_l4_cfg_clkctrl = 0x4a008d20,
- .cm_l4cfg_hw_sem_clkctrl = 0x4a008d28,
- .cm_l4cfg_mailbox_clkctrl = 0x4a008d30,
- .cm_l4cfg_sar_rom_clkctrl = 0x4a008d38,
- .cm_l3instr_clkstctrl = 0x4a008e00,
- .cm_l3instr_l3_3_clkctrl = 0x4a008e20,
- .cm_l3instr_l3_instr_clkctrl = 0x4a008e28,
- .cm_l3instr_intrconn_wp1_clkct = 0x4a008e40,
- .cm_ivahd_clkstctrl = 0x4a008f00,
-
- /* cm2.ivahd */
- .cm_ivahd_ivahd_clkctrl = 0x4a008f20,
- .cm_ivahd_sl2_clkctrl = 0x4a008f28,
-
- /* cm2.cam */
- .cm_cam_clkstctrl = 0x4a009000,
- .cm_cam_iss_clkctrl = 0x4a009020,
- .cm_cam_fdif_clkctrl = 0x4a009028,
-
- /* cm2.dss */
- .cm_dss_clkstctrl = 0x4a009100,
- .cm_dss_dss_clkctrl = 0x4a009120,
-
- /* cm2.sgx */
- .cm_sgx_clkstctrl = 0x4a009200,
- .cm_sgx_sgx_clkctrl = 0x4a009220,
-
- /* cm2.l3init */
- .cm_l3init_clkstctrl = 0x4a009300,
- .cm_l3init_hsmmc1_clkctrl = 0x4a009328,
- .cm_l3init_hsmmc2_clkctrl = 0x4a009330,
- .cm_l3init_hsi_clkctrl = 0x4a009338,
- .cm_l3init_hsusbhost_clkctrl = 0x4a009358,
- .cm_l3init_hsusbotg_clkctrl = 0x4a009360,
- .cm_l3init_hsusbtll_clkctrl = 0x4a009368,
- .cm_l3init_p1500_clkctrl = 0x4a009378,
- .cm_l3init_fsusb_clkctrl = 0x4a0093d0,
- .cm_l3init_usbphy_clkctrl = 0x4a0093e0,
-
- /* cm2.l4per */
- .cm_l4per_clkstctrl = 0x4a009400,
- .cm_l4per_dynamicdep = 0x4a009408,
- .cm_l4per_adc_clkctrl = 0x4a009420,
- .cm_l4per_gptimer10_clkctrl = 0x4a009428,
- .cm_l4per_gptimer11_clkctrl = 0x4a009430,
- .cm_l4per_gptimer2_clkctrl = 0x4a009438,
- .cm_l4per_gptimer3_clkctrl = 0x4a009440,
- .cm_l4per_gptimer4_clkctrl = 0x4a009448,
- .cm_l4per_gptimer9_clkctrl = 0x4a009450,
- .cm_l4per_elm_clkctrl = 0x4a009458,
- .cm_l4per_gpio2_clkctrl = 0x4a009460,
- .cm_l4per_gpio3_clkctrl = 0x4a009468,
- .cm_l4per_gpio4_clkctrl = 0x4a009470,
- .cm_l4per_gpio5_clkctrl = 0x4a009478,
- .cm_l4per_gpio6_clkctrl = 0x4a009480,
- .cm_l4per_hdq1w_clkctrl = 0x4a009488,
- .cm_l4per_hecc1_clkctrl = 0x4a009490,
- .cm_l4per_hecc2_clkctrl = 0x4a009498,
- .cm_l4per_i2c1_clkctrl = 0x4a0094a0,
- .cm_l4per_i2c2_clkctrl = 0x4a0094a8,
- .cm_l4per_i2c3_clkctrl = 0x4a0094b0,
- .cm_l4per_i2c4_clkctrl = 0x4a0094b8,
- .cm_l4per_l4per_clkctrl = 0x4a0094c0,
- .cm_l4per_mcasp2_clkctrl = 0x4a0094d0,
- .cm_l4per_mcasp3_clkctrl = 0x4a0094d8,
- .cm_l4per_mcbsp4_clkctrl = 0x4a0094e0,
- .cm_l4per_mgate_clkctrl = 0x4a0094e8,
- .cm_l4per_mcspi1_clkctrl = 0x4a0094f0,
- .cm_l4per_mcspi2_clkctrl = 0x4a0094f8,
- .cm_l4per_mcspi3_clkctrl = 0x4a009500,
- .cm_l4per_mcspi4_clkctrl = 0x4a009508,
- .cm_l4per_mmcsd3_clkctrl = 0x4a009520,
- .cm_l4per_mmcsd4_clkctrl = 0x4a009528,
- .cm_l4per_msprohg_clkctrl = 0x4a009530,
- .cm_l4per_slimbus2_clkctrl = 0x4a009538,
- .cm_l4per_uart1_clkctrl = 0x4a009540,
- .cm_l4per_uart2_clkctrl = 0x4a009548,
- .cm_l4per_uart3_clkctrl = 0x4a009550,
- .cm_l4per_uart4_clkctrl = 0x4a009558,
- .cm_l4per_mmcsd5_clkctrl = 0x4a009560,
- .cm_l4per_i2c5_clkctrl = 0x4a009568,
- .cm_l4sec_clkstctrl = 0x4a009580,
- .cm_l4sec_staticdep = 0x4a009584,
- .cm_l4sec_dynamicdep = 0x4a009588,
- .cm_l4sec_aes1_clkctrl = 0x4a0095a0,
- .cm_l4sec_aes2_clkctrl = 0x4a0095a8,
- .cm_l4sec_des3des_clkctrl = 0x4a0095b0,
- .cm_l4sec_pkaeip29_clkctrl = 0x4a0095b8,
- .cm_l4sec_rng_clkctrl = 0x4a0095c0,
- .cm_l4sec_sha2md51_clkctrl = 0x4a0095c8,
- .cm_l4sec_cryptodma_clkctrl = 0x4a0095d8,
-
- /* l4 wkup regs */
- .cm_abe_pll_ref_clksel = 0x4a30610c,
- .cm_sys_clksel = 0x4a306110,
- .cm_wkup_clkstctrl = 0x4a307800,
- .cm_wkup_l4wkup_clkctrl = 0x4a307820,
- .cm_wkup_wdtimer1_clkctrl = 0x4a307828,
- .cm_wkup_wdtimer2_clkctrl = 0x4a307830,
- .cm_wkup_gpio1_clkctrl = 0x4a307838,
- .cm_wkup_gptimer1_clkctrl = 0x4a307840,
- .cm_wkup_gptimer12_clkctrl = 0x4a307848,
- .cm_wkup_synctimer_clkctrl = 0x4a307850,
- .cm_wkup_usim_clkctrl = 0x4a307858,
- .cm_wkup_sarram_clkctrl = 0x4a307860,
- .cm_wkup_keyboard_clkctrl = 0x4a307878,
- .cm_wkup_rtc_clkctrl = 0x4a307880,
- .cm_wkup_bandgap_clkctrl = 0x4a307888,
- .prm_vc_val_bypass = 0x4a307ba0,
- .prm_vc_cfg_channel = 0x4a307ba4,
- .prm_vc_cfg_i2c_mode = 0x4a307ba8,
- .prm_vc_cfg_i2c_clk = 0x4a307bac,
-};
-
-struct omap_sys_ctrl_regs const omap4_ctrl = {
- .control_status = 0x4A0022C4,
- .control_std_fuse_die_id_0 = 0x4A002200,
- .control_std_fuse_die_id_1 = 0x4A002208,
- .control_std_fuse_die_id_2 = 0x4A00220C,
- .control_std_fuse_die_id_3 = 0x4A002210,
- .control_std_fuse_opp_bgap = 0x4a002260,
- .control_status = 0x4a0022c4,
- .control_ldosram_iva_voltage_ctrl = 0x4A002320,
- .control_ldosram_mpu_voltage_ctrl = 0x4A002324,
- .control_ldosram_core_voltage_ctrl = 0x4A002328,
- .control_usbotghs_ctrl = 0x4A00233C,
- .control_padconf_core_base = 0x4A100000,
- .control_pbiaslite = 0x4A100600,
- .control_lpddr2io1_0 = 0x4A100638,
- .control_lpddr2io1_1 = 0x4A10063C,
- .control_lpddr2io1_2 = 0x4A100640,
- .control_lpddr2io1_3 = 0x4A100644,
- .control_lpddr2io2_0 = 0x4A100648,
- .control_lpddr2io2_1 = 0x4A10064C,
- .control_lpddr2io2_2 = 0x4A100650,
- .control_lpddr2io2_3 = 0x4A100654,
- .control_efuse_1 = 0x4A100700,
- .control_efuse_2 = 0x4A100704,
- .control_padconf_wkup_base = 0x4A31E000,
-};
diff --git a/arch/arm/mach-omap2/omap4/sdram_elpida.c b/arch/arm/mach-omap2/omap4/sdram_elpida.c
deleted file mode 100644
index a29a264..0000000
--- a/arch/arm/mach-omap2/omap4/sdram_elpida.c
+++ /dev/null
@@ -1,323 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Timing and Organization details of the Elpida parts used in OMAP4
- * SDPs and Panda
- *
- * (C) Copyright 2010
- * Texas Instruments, <www.ti.com>
- *
- * Aneesh V <aneesh@ti.com>
- */
-
-#include <asm/emif.h>
-#include <asm/arch/sys_proto.h>
-
-/*
- * This file provides details of the LPDDR2 SDRAM parts used on OMAP4430
- * SDP and Panda. Since the parts used and geometry are identical for
- * SDP and Panda for a given OMAP4 revision, this information is kept
- * here instead of being in board directory. However the key functions
- * exported are weakly linked so that they can be over-ridden in the board
- * directory if there is a OMAP4 board in the future that uses a different
- * memory device or geometry.
- *
- * For any new board with different memory devices over-ride one or more
- * of the following functions as per the CONFIG flags you intend to enable:
- * - emif_get_reg_dump()
- * - emif_get_dmm_regs()
- * - emif_get_device_details()
- * - emif_get_device_timings()
- */
-
-#ifdef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
-
-const struct emif_regs emif_regs_elpida_200_mhz_2cs = {
- .sdram_config_init = 0x80000eb9,
- .sdram_config = 0x80001ab9,
- .ref_ctrl = 0x0000030c,
- .sdram_tim1 = 0x08648311,
- .sdram_tim2 = 0x101b06ca,
- .sdram_tim3 = 0x0048a19f,
- .read_idle_ctrl = 0x000501ff,
- .zq_config = 0x500b3214,
- .temp_alert_config = 0xd8016893,
- .emif_ddr_phy_ctlr_1_init = 0x049ffff5,
- .emif_ddr_phy_ctlr_1 = 0x049ff808
-};
-
-const struct emif_regs emif_regs_elpida_380_mhz_1cs = {
- .sdram_config_init = 0x80000eb1,
- .sdram_config = 0x80001ab1,
- .ref_ctrl = 0x000005cd,
- .sdram_tim1 = 0x10cb0622,
- .sdram_tim2 = 0x20350d52,
- .sdram_tim3 = 0x00b1431f,
- .read_idle_ctrl = 0x000501ff,
- .zq_config = 0x500b3214,
- .temp_alert_config = 0x58016893,
- .emif_ddr_phy_ctlr_1_init = 0x049ffff5,
- .emif_ddr_phy_ctlr_1 = 0x049ff418
-};
-
-const struct emif_regs emif_regs_elpida_400_mhz_1cs = {
- .sdram_config_init = 0x80800eb2,
- .sdram_config = 0x80801ab2,
- .ref_ctrl = 0x00000618,
- .sdram_tim1 = 0x10eb0662,
- .sdram_tim2 = 0x20370dd2,
- .sdram_tim3 = 0x00b1c33f,
- .read_idle_ctrl = 0x000501ff,
- .zq_config = 0x500b3215,
- .temp_alert_config = 0x58016893,
- .emif_ddr_phy_ctlr_1_init = 0x049ffff5,
- .emif_ddr_phy_ctlr_1 = 0x049ff418
-};
-
-const struct emif_regs emif_regs_elpida_400_mhz_2cs = {
- .sdram_config_init = 0x80000eb9,
- .sdram_config = 0x80001ab9,
- .ref_ctrl = 0x00000618,
- .sdram_tim1 = 0x10eb0662,
- .sdram_tim2 = 0x20370dd2,
- .sdram_tim3 = 0x00b1c33f,
- .read_idle_ctrl = 0x000501ff,
- .zq_config = 0xd00b3214,
- .temp_alert_config = 0xd8016893,
- .emif_ddr_phy_ctlr_1_init = 0x049ffff5,
- .emif_ddr_phy_ctlr_1 = 0x049ff418
-};
-
-const struct dmm_lisa_map_regs lisa_map_2G_x_1_x_2 = {
- .dmm_lisa_map_0 = 0xFF020100,
- .dmm_lisa_map_1 = 0,
- .dmm_lisa_map_2 = 0,
- .dmm_lisa_map_3 = 0x80540300,
- .is_ma_present = 0x0
-};
-
-const struct dmm_lisa_map_regs lisa_map_2G_x_2_x_2 = {
- .dmm_lisa_map_0 = 0xFF020100,
- .dmm_lisa_map_1 = 0,
- .dmm_lisa_map_2 = 0,
- .dmm_lisa_map_3 = 0x80640300,
- .is_ma_present = 0x0
-};
-
-const struct dmm_lisa_map_regs ma_lisa_map_2G_x_2_x_2 = {
- .dmm_lisa_map_0 = 0xFF020100,
- .dmm_lisa_map_1 = 0,
- .dmm_lisa_map_2 = 0,
- .dmm_lisa_map_3 = 0x80640300,
- .is_ma_present = 0x1
-};
-
-static void emif_get_reg_dump_sdp(u32 emif_nr, const struct emif_regs **regs)
-{
- u32 omap4_rev = omap_revision();
-
- /* Same devices and geometry on both EMIFs */
- if (omap4_rev == OMAP4430_ES1_0)
- *regs = &emif_regs_elpida_380_mhz_1cs;
- else if (omap4_rev == OMAP4430_ES2_0)
- *regs = &emif_regs_elpida_200_mhz_2cs;
- else if (omap4_rev < OMAP4470_ES1_0)
- *regs = &emif_regs_elpida_400_mhz_2cs;
- else
- *regs = &emif_regs_elpida_400_mhz_1cs;
-}
-void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs)
- __attribute__((weak, alias("emif_get_reg_dump_sdp")));
-
-static void emif_get_dmm_regs_sdp(const struct dmm_lisa_map_regs
- **dmm_lisa_regs)
-{
- u32 omap_rev = omap_revision();
-
- if (omap_rev == OMAP4430_ES1_0)
- *dmm_lisa_regs = &lisa_map_2G_x_1_x_2;
- else if (omap_rev < OMAP4460_ES1_0)
- *dmm_lisa_regs = &lisa_map_2G_x_2_x_2;
- else
- *dmm_lisa_regs = &ma_lisa_map_2G_x_2_x_2;
-}
-
-void emif_get_dmm_regs(const struct dmm_lisa_map_regs **dmm_lisa_regs)
- __attribute__((weak, alias("emif_get_dmm_regs_sdp")));
-
-#else
-
-const struct lpddr2_device_details elpida_2G_S4_details = {
- .type = LPDDR2_TYPE_S4,
- .density = LPDDR2_DENSITY_2Gb,
- .io_width = LPDDR2_IO_WIDTH_32,
- .manufacturer = LPDDR2_MANUFACTURER_ELPIDA
-};
-
-const struct lpddr2_device_details elpida_4G_S4_details = {
- .type = LPDDR2_TYPE_S4,
- .density = LPDDR2_DENSITY_4Gb,
- .io_width = LPDDR2_IO_WIDTH_32,
- .manufacturer = LPDDR2_MANUFACTURER_ELPIDA
-};
-
-struct lpddr2_device_details *emif_get_device_details_sdp(u32 emif_nr, u8 cs,
- struct lpddr2_device_details *lpddr2_dev_details)
-{
- u32 omap_rev = omap_revision();
-
- /* EMIF1 & EMIF2 have identical configuration */
- if (((omap_rev == OMAP4430_ES1_0) || (omap_rev == OMAP4470_ES1_0))
- && (cs == CS1)) {
- /* Nothing connected on CS1 for 4430/4470 ES1.0 */
- return NULL;
- } else if (omap_rev < OMAP4470_ES1_0) {
- /* In all other 4430/4460 cases Elpida 2G device */
- *lpddr2_dev_details = elpida_2G_S4_details;
- } else {
- /* 4470: 4G device */
- *lpddr2_dev_details = elpida_4G_S4_details;
- }
- return lpddr2_dev_details;
-}
-
-struct lpddr2_device_details *emif_get_device_details(u32 emif_nr, u8 cs,
- struct lpddr2_device_details *lpddr2_dev_details)
- __attribute__((weak, alias("emif_get_device_details_sdp")));
-
-#endif /* CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS */
-
-#ifndef CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
-static const struct lpddr2_ac_timings timings_elpida_400_mhz = {
- .max_freq = 400000000,
- .RL = 6,
- .tRPab = 21,
- .tRCD = 18,
- .tWR = 15,
- .tRASmin = 42,
- .tRRD = 10,
- .tWTRx2 = 15,
- .tXSR = 140,
- .tXPx2 = 15,
- .tRFCab = 130,
- .tRTPx2 = 15,
- .tCKE = 3,
- .tCKESR = 15,
- .tZQCS = 90,
- .tZQCL = 360,
- .tZQINIT = 1000,
- .tDQSCKMAXx2 = 11,
- .tRASmax = 70,
- .tFAW = 50
-};
-
-static const struct lpddr2_ac_timings timings_elpida_333_mhz = {
- .max_freq = 333000000,
- .RL = 5,
- .tRPab = 21,
- .tRCD = 18,
- .tWR = 15,
- .tRASmin = 42,
- .tRRD = 10,
- .tWTRx2 = 15,
- .tXSR = 140,
- .tXPx2 = 15,
- .tRFCab = 130,
- .tRTPx2 = 15,
- .tCKE = 3,
- .tCKESR = 15,
- .tZQCS = 90,
- .tZQCL = 360,
- .tZQINIT = 1000,
- .tDQSCKMAXx2 = 11,
- .tRASmax = 70,
- .tFAW = 50
-};
-
-static const struct lpddr2_ac_timings timings_elpida_200_mhz = {
- .max_freq = 200000000,
- .RL = 3,
- .tRPab = 21,
- .tRCD = 18,
- .tWR = 15,
- .tRASmin = 42,
- .tRRD = 10,
- .tWTRx2 = 20,
- .tXSR = 140,
- .tXPx2 = 15,
- .tRFCab = 130,
- .tRTPx2 = 15,
- .tCKE = 3,
- .tCKESR = 15,
- .tZQCS = 90,
- .tZQCL = 360,
- .tZQINIT = 1000,
- .tDQSCKMAXx2 = 11,
- .tRASmax = 70,
- .tFAW = 50
-};
-
-static const struct lpddr2_min_tck min_tck_elpida = {
- .tRL = 3,
- .tRP_AB = 3,
- .tRCD = 3,
- .tWR = 3,
- .tRAS_MIN = 3,
- .tRRD = 2,
- .tWTR = 2,
- .tXP = 2,
- .tRTP = 2,
- .tCKE = 3,
- .tCKESR = 3,
- .tFAW = 8
-};
-
-static const struct lpddr2_ac_timings *elpida_ac_timings[MAX_NUM_SPEEDBINS] = {
- &timings_elpida_200_mhz,
- &timings_elpida_333_mhz,
- &timings_elpida_400_mhz
-};
-
-const struct lpddr2_device_timings elpida_2G_S4_timings = {
- .ac_timings = elpida_ac_timings,
- .min_tck = &min_tck_elpida,
-};
-
-void emif_get_device_timings_sdp(u32 emif_nr,
- const struct lpddr2_device_timings **cs0_device_timings,
- const struct lpddr2_device_timings **cs1_device_timings)
-{
- u32 omap_rev = omap_revision();
-
- /* Identical devices on EMIF1 & EMIF2 */
- *cs0_device_timings = &elpida_2G_S4_timings;
-
- if ((omap_rev == OMAP4430_ES1_0) || (omap_rev == OMAP4470_ES1_0))
- *cs1_device_timings = NULL;
- else
- *cs1_device_timings = &elpida_2G_S4_timings;
-}
-
-void emif_get_device_timings(u32 emif_nr,
- const struct lpddr2_device_timings **cs0_device_timings,
- const struct lpddr2_device_timings **cs1_device_timings)
- __attribute__((weak, alias("emif_get_device_timings_sdp")));
-
-#endif /* CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS */
-
-const struct lpddr2_mr_regs mr_regs = {
- .mr1 = MR1_BL_8_BT_SEQ_WRAP_EN_NWR_3,
- .mr2 = 0x4,
- .mr3 = -1,
- .mr10 = MR10_ZQ_ZQINIT,
- .mr16 = MR16_REF_FULL_ARRAY
-};
-
-void get_lpddr2_mr_regs(const struct lpddr2_mr_regs **regs)
-{
- *regs = &mr_regs;
-}
-
-__weak const struct read_write_regs *get_bug_regs(u32 *iterations)
-{
- return 0;
-}