mpc8641: Change 32-bit memory map
The memory map on the 8641hpcn is modified to look more like
the 85xx boards; this is a step towards a more standardized
layout going forward. As part of this change, we now relocate
the flash.
The regions for some of the mappings were far larger than they
needed to be. I have reduced the mappings to match the
actual sizes supported by the hardware.
In addition I have removed the comments at the head
of the BAT blocks in the config file, rather than updating
them. These get horribly out of date, and it's a simple
matter to look at the defines to see what they are set to
since everything is right here in the same file.
Documentation has been changed to reflect the new map, as this
change is user visible, and affects the OS which runs post-uboot.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
diff --git a/doc/README.mpc8641hpcn b/doc/README.mpc8641hpcn
index 2c3c703..0a6e715 100644
--- a/doc/README.mpc8641hpcn
+++ b/doc/README.mpc8641hpcn
@@ -79,51 +79,53 @@
3. Flash U-Boot
---------------
-The flash range 0xFF800000 to 0xFFFFFFFF can be divided into 2 halves.
+The flash range 0xEF800000 to 0xEFFFFFFF can be divided into 2 halves.
It is possible to use either half to boot using u-boot. Switch 5 bit 2
is used for this purpose.
-0xFF800000 to 0xFFBFFFFF - 4MB
-0xFFC00000 to 0xFFFFFFFF - 4MB
-When this bit is 0, U-Boot is at 0xFFF00000.
-When this bit is 1, U-Boot is at 0xFFB00000.
+0xEF800000 to 0xEFBFFFFF - 4MB
+0xEFC00000 to 0xEFFFFFFF - 4MB
+When this bit is 0, U-Boot is at 0xEFF00000.
+When this bit is 1, U-Boot is at 0xEFB00000.
Use the above mentioned flash commands to program the other half, and
use switch 5, bit 2 to alternate between the halves. Note: The booting
-version of U-Boot will always be at 0xFFF00000.
+version of U-Boot will always be at 0xEFF00000.
-To Flash U-Boot into the booting bank (0xFFC00000 - 0xFFFFFFFF):
+To Flash U-Boot into the booting bank (0xEFC00000 - 0xEFFFFFFF):
tftp 1000000 u-boot.bin
protect off all
- erase fff00000 +$filesize
- cp.b 1000000 fff00000 $filesize
+ erase eff00000 +$filesize
+ cp.b 1000000 eff00000 $filesize
or use tftpflash command:
run tftpflash
-To Flash U-boot into the alternative bank (0xFF800000 - 0xFFBFFFFF):
+To Flash U-boot into the alternative bank (0xEF800000 - 0xEFBFFFFF):
tftp 1000000 u-boot.bin
- erase ffb00000 +$filesize
- cp.b 1000000 ffb00000 $filesize
+ erase efb00000 +$filesize
+ cp.b 1000000 efb00000 $filesize
4. Memory Map
-------------
+NOTE: RIO and PCI are mutually exclusive, so they share an address
Memory Range Device Size
------------ ------ ----
0x0000_0000 0x7fff_ffff DDR 2G
+ 0x8000_0000 0x9fff_ffff RIO MEM 512M
0x8000_0000 0x9fff_ffff PCI1/PEX1 MEM 512M
- 0xa000_0000 0xafff_ffff PCI2/PEX2 MEM 512M
- 0xf800_0000 0xf80f_ffff CCSR 1M
- 0xf810_0000 0xf81f_ffff PIXIS 1M
+ 0xa000_0000 0xbfff_ffff PCI2/PEX2 MEM 512M
+ 0xffe0_0000 0xffef_ffff CCSR 1M
+ 0xffdf_0000 0xffdf_7fff PIXIS 8K
+ 0xffdf_8000 0xffdf_ffff CF 8K
0xf840_0000 0xf840_3fff Stack space 32K
- 0xe200_0000 0xe2ff_ffff PCI1/PEX1 IO 16M
- 0xe300_0000 0xe3ff_ffff PCI2/PEX2 IO 16M
- 0xfe00_0000 0xfeff_ffff Flash(alternate)16M
- 0xff00_0000 0xffff_ffff Flash(boot bank)16M
+ 0xffc0_0000 0xffc0_ffff PCI1/PEX1 IO 64K
+ 0xffc1_0000 0xffc1_ffff PCI2/PEX2 IO 64K
+ 0xef80_0000 0xefff_ffff Flash 8M
5. pixis_reset command
--------------------