armv8: ls1012ardb: support hwconfig for eSDHC1 enabling
I2C reading for DIP switch setting is not reliable for LS1012ARDB
RevD and later versions. This patch is to add hwconfig support to
enable/disable eSDHC1 manually for these boards. Also drop 'status'
fix-up for eSDHC0 and leave it as it is. It shouldn't always be
fixed up with 'okay'.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
diff --git a/board/freescale/ls1012ardb/ls1012ardb.c b/board/freescale/ls1012ardb/ls1012ardb.c
index 421b0a7..286f9d8 100644
--- a/board/freescale/ls1012ardb/ls1012ardb.c
+++ b/board/freescale/ls1012ardb/ls1012ardb.c
@@ -152,34 +152,49 @@
int esdhc_status_fixup(void *blob, const char *compat)
{
- char esdhc0_path[] = "/soc/esdhc@1560000";
char esdhc1_path[] = "/soc/esdhc@1580000";
- u8 io = 0;
+ bool sdhc2_en = false;
u8 mux_sdhc2;
-
- do_fixup_by_path(blob, esdhc0_path, "status", "okay",
- sizeof("okay"), 1);
+ u8 io = 0;
i2c_set_bus_num(0);
- /*
- * The I2C IO-expander for mux select is used to control the muxing
- * of various onboard interfaces.
- *
- * IO1[3:2] indicates SDHC2 interface demultiplexer select lines.
- * 00 - SDIO wifi
- * 01 - GPIO (to Arduino)
- * 10 - eMMC Memory
- * 11 - SPI
- */
- if (i2c_read(I2C_MUX_IO_ADDR, I2C_MUX_IO_0, 1, &io, 1) < 0) {
+ /* IO1[7:3] is the field of board revision info. */
+ if (i2c_read(I2C_MUX_IO_ADDR, I2C_MUX_IO_1, 1, &io, 1) < 0) {
printf("Error reading i2c boot information!\n");
- return 0; /* Don't want to hang() on this error */
+ return 0;
}
- mux_sdhc2 = (io & 0x0c) >> 2;
- /* Enable SDHC2 only when use SDIO wifi and eMMC */
- if (mux_sdhc2 == 2 || mux_sdhc2 == 0)
+ /* hwconfig method is used for RevD and later versions. */
+ if ((io & SW_REV_MASK) <= SW_REV_D) {
+#ifdef CONFIG_HWCONFIG
+ if (hwconfig("esdhc1"))
+ sdhc2_en = true;
+#endif
+ } else {
+ /*
+ * The I2C IO-expander for mux select is used to control
+ * the muxing of various onboard interfaces.
+ *
+ * IO0[3:2] indicates SDHC2 interface demultiplexer
+ * select lines.
+ * 00 - SDIO wifi
+ * 01 - GPIO (to Arduino)
+ * 10 - eMMC Memory
+ * 11 - SPI
+ */
+ if (i2c_read(I2C_MUX_IO_ADDR, I2C_MUX_IO_0, 1, &io, 1) < 0) {
+ printf("Error reading i2c boot information!\n");
+ return 0;
+ }
+
+ mux_sdhc2 = (io & 0x0c) >> 2;
+ /* Enable SDHC2 only when use SDIO wifi and eMMC */
+ if (mux_sdhc2 == 2 || mux_sdhc2 == 0)
+ sdhc2_en = true;
+ }
+
+ if (sdhc2_en)
do_fixup_by_path(blob, esdhc1_path, "status", "okay",
sizeof("okay"), 1);
else